WTB 67-68 Driveline Seattle/Portland area - The 1947 - Present Chevrolet & GMC Truck Message Board Network

WinDancer · 02-07-2007, 09:55 PM

for a turbo 400 shortshaft, SWB, 2wd with leaf-spring rear end
Thanks,
Dave

**67sss** · 02-07-2007, 10:23 PM

what length? are you needing the 400 yoke also?

WinDancer · 02-08-2007, 12:02 AM

I haven't one that fits to measure- my original one is too short. Converted from 350/350 long-shaft to 396 and a 400 trans with short shaft-.
I do want the front yoke, also.

Thanks,
Dave

**67sss** · 02-08-2007, 07:49 PM

go lay under the truck and measure from center of cups on the rearend to the tail of the tranny and then subtract 2 or 3 inches, that'll be the center of the tranny yoke. I have 2 or 3 laying around here, but to be honest, you can get the measurement and go to the junkyard and find the right length. The one in my 67 shorty is out of a dodge van. Let me know, one of these might be the right length.

WinDancer · 02-11-2007, 02:54 PM

ttt

WinDancer · 02-27-2007, 11:52 PM

Got the new length measured- 60.25 end to end. If you have one would there be a way to get it near Olympia?
Thanks,

cabinetguy · 02-28-2007, 12:58 AM

do you have the top mount or bottom mount carrier bearing? If you want a direct bolt up this matters, right?

02-07-2007, 09:55 PM	#1
WinDancer The Original HotRod KnifeMaker Join Date: Jan 2007 Location: Tenino, Washington Posts: 811	WTB 67-68 Driveline Seattle/Portland area for a turbo 400 shortshaft, SWB, 2wd with leaf-spring rear end Thanks, Dave

02-07-2007, 10:23 PM	#2
67sss Registered User Join Date: Nov 2002 Location: Mt. Vernon, WA.. Posts: 2,325	Re: WTB 67-68 Driveline Seattle/Portland area what length? are you needing the 400 yoke also?

02-08-2007, 12:02 AM	#3
WinDancer The Original HotRod KnifeMaker Join Date: Jan 2007 Location: Tenino, Washington Posts: 811	Re: WTB 67-68 Driveline Seattle/Portland area I haven't one that fits to measure- my original one is too short. Converted from 350/350 long-shaft to 396 and a 400 trans with short shaft-. I do want the front yoke, also. Thanks, Dave

02-08-2007, 07:49 PM	#4
67sss Registered User Join Date: Nov 2002 Location: Mt. Vernon, WA.. Posts: 2,325	Re: WTB 67-68 Driveline Seattle/Portland area go lay under the truck and measure from center of cups on the rearend to the tail of the tranny and then subtract 2 or 3 inches, that'll be the center of the tranny yoke. I have 2 or 3 laying around here, but to be honest, you can get the measurement and go to the junkyard and find the right length. The one in my 67 shorty is out of a dodge van. Let me know, one of these might be the right length.

02-11-2007, 02:54 PM	#5
WinDancer The Original HotRod KnifeMaker Join Date: Jan 2007 Location: Tenino, Washington Posts: 811	Re: WTB 67-68 Driveline Seattle/Portland area ttt __________________ Dave 69 GMC SWB 2WD 454 Turbo 400

02-27-2007, 11:52 PM	#6
WinDancer The Original HotRod KnifeMaker Join Date: Jan 2007 Location: Tenino, Washington Posts: 811	Re: WTB 67-68 Driveline Seattle/Portland area Got the new length measured- 60.25 end to end. If you have one would there be a way to get it near Olympia? Thanks, __________________ Dave 69 GMC SWB 2WD 454 Turbo 400

02-28-2007, 12:58 AM	#7
cabinetguy 67 shorty Join Date: Feb 2007 Location: Graham,Wa. Posts: 190	Re: WTB 67-68 Driveline Seattle/Portland area do you have the top mount or bottom mount carrier bearing? If you want a direct bolt up this matters, right? __________________ 67 SWB with enough parts to build two



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.