|
|
|
05-12-2007, 07:31 PM
|
#1 |
|
1972 Shorty Owner
Join Date: Feb 2007
Location: Stationed in Cali , born and raised in PHX Arizona.
Posts: 796
|
Engine Stand Question
This is probably a stupid question but i just bought this Engine Stand and i need to know what bolts i need. The damn thing didnt come with any ..... (i have never used one of these)
I am putting a 5.3L on the stand. The bolts i have are not long enough. Any help would be huge! -Hart
__________________
1972 Chevy Shorty C-10- Project In Work http://67-72chevytrucks.com/gallery/...ATT1721941.jpg- New Project |
|
|
|
05-12-2007, 07:34 PM
|
#2 |
|
Gone Fishing
Join Date: Aug 2005
Location: Fort Worth, Texas 76135
Posts: 12,361
|
Re: Engine Stand Question
I think the 5.3 is metric. Probably needs to be about 4 inches long
__________________
68 Chevy Short Fleetside LSX Swap Under Way 3.73 posi 2.5/4 drop  Frame of resto has been started2022 Hyundai Tucson Limited 2019 Chevy Traverse Redline Edition Wifes Ride Build Thread http://67-72chevytrucks.com/vboard/s...=1#post3483616 |
|
|
|
|
05-12-2007, 07:43 PM
|
#3 |
|
1972 Shorty Owner
Join Date: Feb 2007
Location: Stationed in Cali , born and raised in PHX Arizona.
Posts: 796
|
Re: Engine Stand Question
and i just tighten it right to the block?
__________________
1972 Chevy Shorty C-10- Project In Work http://67-72chevytrucks.com/gallery/...ATT1721941.jpg- New Project |
|
|
|
|
05-12-2007, 07:50 PM
|
#4 |
|
Gone Fishing
Join Date: Aug 2005
Location: Fort Worth, Texas 76135
Posts: 12,361
|
Re: Engine Stand Question
Yup thats what I've done in the past with some 350's
__________________
68 Chevy Short Fleetside LSX Swap Under Way 3.73 posi 2.5/4 drop Frame of resto has been started2022 Hyundai Tucson Limited 2019 Chevy Traverse Redline Edition Wifes Ride Build Thread http://67-72chevytrucks.com/vboard/s...=1#post3483616 |
|
|
|
|
05-12-2007, 08:22 PM
|
#5 |
|
Sierra Grande Club
Join Date: Jan 2007
Location: New Mexico USA
Posts: 2,433
|
Re: Engine Stand Question
You will also want to spread the load as wide as possible. If the picture is how its going to get mounted, it looks pretty good IMO.
s/t
__________________
1971 GMC Sierra Grande, 1/2 ton short wide, original 4 bolt 010 020 block & heads. (matching #'s). 383 stroker, SMI q jet 750 cfm, Lunati Voodoo 60102 cam, Scorpion roller rockers, Spin Tech pro street mufflers with X pipe. 
|
|
|
|
|
05-12-2007, 10:06 PM
|
#6 |
|
LS1 Lover
Join Date: Sep 2005
Location: Austin, TX
Posts: 474
|
Re: Engine Stand Question
They are metric bolts go to your local hardware store and pick up some. I can't think of the thread pitch off the top of my head but I have to use washers to space mine out the proper size.
__________________
USMC 
|
|
|
|
|
05-12-2007, 11:33 PM
|
#7 |
|
Too many projects!!!
Join Date: Jul 2000
Location: Jacksonville, Florida
Posts: 508
|
Re: Engine Stand Question
I know it's probably not needed...but I always use GRADE 8 bolts for holding up an engine on a stand.
The way I usally put an engine in a stand..is to pull the holder out of the stand and bolt it to the engine first (engine is hanging from hoist)..leaving all the bolts just snug, center the holder..and then tighten them down evenly...and then place the stand back onto the holder, and then lower the hoist...
__________________
Sean  1995 Buick Roadmaster Sedan 2004 Chevy Trailblazer 5.3L V8 1963 Chevy Biscayne 4D Sedan 1971 Chevy C10 (now have 70 cab & frame) 1968 Chevy C10 (parts for the 70) 1991 Oldsmobile Custom Cruiser (Chevy 355 motor) 1937 Pontiac 8 4D Touring Sedan (in pieces) Jacksonville, Florida |
|
|
|
|
05-13-2007, 12:57 AM
|
#8 |
|
Commander Taco Bello
Join Date: Sep 2006
Location: Des Moines, Iowa
Posts: 2,232
|
Re: Engine Stand Question
|
|
|
|
|
05-12-2007, 11:32 PM
|
#9 |
|
Senior Member
Join Date: May 2004
Location: johnstown, NY
Posts: 2,393
|
Re: Engine Stand Question
get grade 8
|
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
