67' Truck Build

[TYZ 67]

Just thought I would start a thread on my build. Bought my truck about a month ago. Have it mostly stripped down minus the cab, bed and suspension. I will be starting with some of the body work first (patches, welding, etc...). Wish I could start with the suspension first, just don't have the $$$ to do so yet. I will be bagging it with a triangulated 4 link in the rear and I really like the C4 dropmember Porterbuilt has. Not sure if I am going to do 20's or 22's, haven't found to many pics of these trucks with 22's. If anyone has good pics please post. I am probably going with the Coys C5 polished or gun metal. Speaking of posting pictures how do you post them. It asks for a URL to post the picture. It won't let me post from my computer. I will post some pictures when I figure it out.

[BurnoutNova]

you need to use a host for your pictures such as picturetrail... then post the url inside [img]....[/img]

[CrashEd]

If you go to the [go advanced] post theres a paper clip that will let you put pictures up from your computer.
Ed

[Spray-Bomb]

IMO, there is no reason to run 22's
You can't see the difference, cuz it's just an inch bigger across & you have just that much less tire

I have 20's & wish they were 18's, but it's all a personal choice

[bagged74]

Originally Posted by Spray-Bomb

IMO, there is no reason to run 22's
You can't see the difference, cuz it's just an inch bigger across & you have just that much less tire

actually its 2 inches, and you can still have the same sidewall ratio as long as there is room.
22s can look good , but like Spray-bomb said its personal preference

[TYZ 67]

I'll probably go with 20's. What is the best way to do the front inner fender wells when bagged. I want my truck to sit about an inch or so off the ground when fully deflated. Is there a way to raise the stock fender wells? I will be raising the rear fender wells and bed. I would like to keep a semi classic look. By the way this site is great. Everyone is helpful and has great ideas. Thanks!

[Spray-Bomb]

Originally Posted by bagged74

actually its 2 inches, and you can still have the same sidewall ratio as long as there is room.
22s can look good , but like Spray-bomb said its personal preference

I said Across the wheel, thats 1 inch less tire

Originally Posted by TYZ 67

I'll probably go with 20's. What is the best way to do the front inner fender wells when bagged. I want my truck to sit about an inch or so off the ground when fully deflated. Is there a way to raise the stock fender wells? I will be raising the rear fender wells and bed. I would like to keep a semi classic look. By the way this site is great. Everyone is helpful and has great ideas. Thanks!

I don't have mine bagged quite yet, so I can't help you here except for this link

http://67-72chevytrucks.com/vboard/s...d.php?t=250756

[Raguemoe]

Originally Posted by Spray-Bomb

IMO, there is no reason to run 22's
You can't see the difference, cuz it's just an inch bigger across & you have just that much less tire

I have 20's & wish they were 18's, but it's all a personal choice

What??? I can see a difference!

[bagged74]

Originally Posted by Raguemoe

What??? I can see a difference!

me too

[TYZ 67]

Those trucks look sweet. I'll might go staggered that looks good. 20's in front will probably eliminate some clearance issues. Here's some pic of mine so far.

Attachment 287136





Hopefully these show up.

[Frizzle Fry]

Originally Posted by bagged74

me too

Me too Nice project!

[72 Cheyenne402]

Originally Posted by Raguemoe

What??? I can see a difference!

This truck is sick man!!! I went with 18x8 and 20x9 in the rear. I almost went 20 & 22's I love your truck Raguemoe and can't wait to see more of it

[Spray-Bomb]

Never mind, Whatever, Blah Blah Blah

[TYZ 67]

Raguemoe- Your truck looks sweet, couple of questions. What front suspension set up are you using, Dropmember or stock? Does it lay completely on the ground or just above. I want to be about an inch or so off. I like how your front wheels are straight up and down. Are the rear bags on the link bars? If so are the bars strong enough? Thanks for all you input so far. Where is Highland California at by the way?

[Raguemoe]

Originally Posted by TYZ 67

Raguemoe- Your truck looks sweet, couple of questions. What front suspension set up are you using, Dropmember or stock? Does it lay completely on the ground or just above. I want to be about an inch or so off. I like how your front wheels are straight up and down. Are the rear bags on the link bars? If so are the bars strong enough? Thanks for all you input so far. Where is Highland California at by the way?

Stock front set-up w/Art control arms. Front crossmember is 1/2" off the ground (frame about 2 1/2"). I had a custom 3-link installed in the rear. Highland is 40 miles from Orange County. Just below Big Bear! More pics

[Joe67]

Originally Posted by TYZ 67

Just thought I would start a thread on my build. Bought my truck about a month ago. Have it mostly stripped down minus the cab, bed and suspension. I will be starting with some of the body work first (patches, welding, etc...). Wish I could start with the suspension first, just don't have the $$$ to do so yet. I will be bagging it with a triangulated 4 link in the rear and I really like the C4 dropmember Porterbuilt has. Not sure if I am going to do 20's or 22's, haven't found to many pics of these trucks with 22's. If anyone has good pics please post. I am probably going with the Coys C5 polished or gun metal. Speaking of posting pictures how do you post them. It asks for a URL to post the picture. It won't let me post from my computer. I will post some pictures when I figure it out.

Sounds like a sweet poject

I moved it to the BUILDS forum - run whatever wheel you like, that is what makes this hobby so great

[TYZ 67]

Well I decided not to go with the drop member, just to expensive for me. Plus I want to stay about an inch or so off the ground so there is no need for it. I might still try and incorporate a rack and pinion steering.

[N2TRUX]

Originally Posted by TYZ 67

Well I decided not to go with the drop member, just to expensive for me. Plus I want to stay about an inch or so off the ground so there is no need for it. I might still try and incorporate a rack and pinion steering.

When you say " stay about an inch or so off the ground " exactly what are you referring to? Are you talking about the frame, the rockers, or your crossmember?

In the event that you are not aware, the stock crossmember is the lowest point of your front suspension. If you lower your truck using bags and you modify the inner fenders the first thing to touch the ground will be your A-arm.


The pic below is my 82 Blazer, but it gives you an idea of what I mean....

[TYZ 67]

N2Trux- I want the lowest part of the truck about 1" off. I had a buddy who's truck layed frame but he also had a bag blow out while driving. I don't want it to slam on the ground(frame will be powder coated) if that were to ever happen. I am also going to use the ART arms.

Raguemoe- Thanks for the info. Like the firewall. Do you have to modify the inner front fenders or do the wheels not touch? I'll post some more pics when I get some more visible progress.

[Raguemoe]

Originally Posted by TYZ 67

N2Trux- I want the lowest part of the truck about 1" off. I had a buddy who's truck layed frame but he also had a bag blow out while driving. I don't want it to slam on the ground(frame will be powder coated) if that were to ever happen. I am also going to use the ART arms.

Raguemoe- Thanks for the info. Like the firewall. Do you have to modify the inner front fenders or do the wheels not touch? I'll post some more pics when I get some more visible progress.

Custom fender wells!

[TYZ 67]

Raguemoe you truck is sweet! Can't wait till mine is that far along. What hood hinges are those. Custom fenders look great. I may do custom but I think I might try and keep the original for a semi classic look.

[Raguemoe]

Originally Posted by TYZ 67

Raguemoe you truck is sweet! Can't wait till mine is that far along. What hood hinges are those. Custom fenders look great. I may do custom but I think I might try and keep the original for a semi classic look.

Fenders are made from trailer fenders and hinges are from a Mercedez car.

[PBFAB.COM]

When combining the Dropmember with a stock spindle and a 27" tall tire, the frame-rail will set just under 2" off the ground when fully deflated. The main advantages of the Dropmember are the crossmember to ground clearance, and rack and pinion steering. It's not in everybody's budget, but it also isn't just for the guys who want to "lay frame" on 22's.

[TYZ 67]

Got some patch panels today. Hope to get them in this weekend. I'll post some new pics when done.

[TYZ 67]

Well my plans for this truck changed quite a bit. I sold my frame and trashed my cab (way too rusted out). Now I am building my own frame and suspension (thanks to abadsvt and his work). I really like the pro touring theme but I havn't seen too many truck so I decided I'm going that route. here are a few progress pics, hopefully I will be getting the frame rails done in a week or so.

http://s262.photobucket.com/albums/i...av_album_album