![]() |
|
![]() |
#1 |
Senior Member
Join Date: Mar 2003
Location: St robert Mo
Posts: 2,001
|
thorley headers
Who is running the full tube tri-y? Do the nickle ones blue and look bad after a while I see they have ceramic coated ones as well is it worth the extra money?
Next How do they fit, do you have to notch the frame, do they clear motor mounts? Also how many inches below the frame do they hang? If you have any pics and part numbers that would rock. I am at a crossroad between the thorleys and the ECE sanderson 3/4 length? I have a 3 inch drop in front but am running some nasty poor fitting headmans now(PO) and they are full lengh and I have never bottomed them out yet. So I am thinking more power full length, better look and less hanging exhaust 3/4. Anyway I know the ECE ones fit nice and look really good. But still would like to run full tube for the low end pull and the thorleys look sick. thanks for any help
__________________
1968 c10 lowered 3" 4" 355/Th400 built by Hatfield racing in joplin MO |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Sep 2007
Location: laura, ohio
Posts: 935
|
Re: thorley headers
i know 70cst has em on his ride and they got very oxidized and started to rust a bit..i dont know what model # they are though so he can chime in and tell you
|
![]() |
![]() |
![]() |
#3 |
Senior Member
![]() Join Date: Feb 2001
Location: New Madison, Ohio
Posts: 21,365
|
Re: thorley headers
Hey 76bonanza ...
I have tri-y's on my 402BB. They are not ceramic which was a bad decision on my part. Fit was good as I called and talked to the Tech. department and they were very helpful and gave me the correct part number. The sound with flowmaster 40 series is a very deep throat sound. I hope this helps. ![]()
__________________
A husband can be right...or...A husband can be happy. ![]() 67-72 Chevy and GMC Trucks...The Classic Truck for the Classic Folk. ![]() 1970 CST Two tone green, 402BB, 400 Automatic, Tach, Buckets, AC, AM-FM, Tilt, GM CB, GM 8 Tract, LWB, etc ![]() ![]() JOHN 17:3...The better side of "LIFE" Remember: Everyday is a good day...Some are just gooder! Last edited by 70cst; 09-03-2007 at 08:24 PM. |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Mar 2007
Location: VANCOUVER ISLAND, B.C., Canada
Posts: 1,602
|
Re: thorley headers
Sanderson 3/4 length for me for all the same reasons that you stated and one more reason as well is I do bottom out from time to time with these full length Hedman headers and I can't take it anymore (IT'S EMBARRASSING AS ALL GET OUT!!). Ceramic coating is the only way to go. Sanderson coats theirs in and out, gauranteed not to leak 3/8 flange and made to fit our trucks. What more can a guy ask for. Ceramic coatings may grey right at where they bolt on to the engine but that kinda blends unlike a chrome finish that goes blue.
ECE is out of stock right now but I'm hoping their stock will be in wed. of this week. Bottom end tork or bottoming out .... trust me you will notice bottoming out more then the bottom end tork that might be lacking will ever be noticed. esll. ![]() These are sweet can hardly wait till their at my house .....
__________________
Tomorrow is for doing today's stuff. ![]() ************************************* This truck has just the right amount of energy for me! ![]() Author: Warren Lake .... (member) |
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: Mar 2003
Location: St robert Mo
Posts: 2,001
|
Re: thorley headers
Hey 70 cst can you see how low below the frame they are. the headers I have now the bottom of the header flange is about three inches below frame and I have no clearance problems so far. Can anyone comment on the cermic coated ones?
__________________
1968 c10 lowered 3" 4" 355/Th400 built by Hatfield racing in joplin MO |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Sep 2007
Location: laura, ohio
Posts: 935
|
Re: thorley headers
i can get that for you tomarow
|
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: Mar 2003
Location: St robert Mo
Posts: 2,001
|
Re: thorley headers
Thanks that would help a bunch I have a 3inch drop in front and really don't scrap nothing now. But would not want them to hang much lower.
__________________
1968 c10 lowered 3" 4" 355/Th400 built by Hatfield racing in joplin MO |
![]() |
![]() |
![]() |
#8 |
Senior Member
![]() Join Date: Feb 2001
Location: New Madison, Ohio
Posts: 21,365
|
Re: thorley headers
Hey 76bonanza ...
I think my truck has a 2"/4" drop w/o any issues. But to be honest the truck has been driven very little since the headers were installed. I plan on having all the mechanics done this fall/winter and I am going to see if I can get the tri-y's ceramic coated. As mentioned I did not pay the extra for the ceramic coating...that was real ![]() ![]() The truck is stored in the corn crib so 70cstjr can get the pics for you.
__________________
A husband can be right...or...A husband can be happy. ![]() 67-72 Chevy and GMC Trucks...The Classic Truck for the Classic Folk. ![]() 1970 CST Two tone green, 402BB, 400 Automatic, Tach, Buckets, AC, AM-FM, Tilt, GM CB, GM 8 Tract, LWB, etc ![]() ![]() JOHN 17:3...The better side of "LIFE" Remember: Everyday is a good day...Some are just gooder! |
![]() |
![]() |
![]() |
Bookmarks |
|
|