Pre bent exhaust for our trucks? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

chevydog66 · 09-05-2007, 12:32 PM

Does anyone make a bolt on 2 1/2" exhaust system for our trucks? I prefer mandrel bent over the local exhaust shop bender. Names like Flowmaster, Magnaflow, Heartbeat, do they make em for our trucks? How well do they fit?

Jcentsr6 · 09-05-2007, 12:38 PM

I am going to the local Mandrel bend shop this week to get my header back system made. I am running hooker headers with flowmaster 44 mufflers attached...then the mandrel benmt stuff out to the side before the rear wheels. I can give you the info once im finished everything...($$ and where to get)

68 P.O.S. · 09-05-2007, 12:59 PM

Doesn't Magnaflow offer that exact setup?

70c10 · 09-05-2007, 01:06 PM

I thought Magnaflow's kit went over the axle- all stainless!

Jay, I can't wait to get the details/pics!

**Shock_Me** · 09-05-2007, 01:06 PM

Yes Magnaflow has a kit. LMC carries it. Once you get the part number, plug it into an Ebay search. It's sold by a few Ebay sellers.

It's made for longbeds, but can be cut down for shortbeds.

Pete

mrein3 · 09-05-2007, 01:11 PM

Quote:

Originally Posted by chevydog66

Does anyone make a bolt on 2 1/2" exhaust system for our trucks? I prefer mandrel bent over the local exhaust shop bender. Names like Flowmaster, Magnaflow, Heartbeat, do they make em for our trucks? How well do they fit?

I installed the kit LMC has in their catalog. The kit fit great.
The only piece I needed to buy that wasn't included in the kit was an exhaust hanger because my truck was NOT a factory dual exhaust truck.

The LMC kit was made by Heartbeat here in Minnesota.

JameslovesJammie · 09-05-2007, 01:36 PM

The Magnaflow setup is for coil spring only, but I don't remember why. I'll look in old emails from them and find out. IMHO, it's one heck of a deal. It sells for ~$500 through Summit. Their Dyno showed a 10 HP and 22 lb/ft gain in torque. It's an all stainless, mandrel bent kit. Great product!

http://www.magnaflow.com/02product/dynos/c1020.jpg

http://www.magnaflow.com/02product/s...e=Trucks&id=76

70GMCer · 09-05-2007, 04:22 PM

From Summit.........and a about $150.00 cheaper

http://store.summitracing.com/partde...5&autoview=sku

72BlckButy · 09-05-2007, 08:22 PM

It looks like it would fit nice.

70c10, any pics yet? Can't wait to see them.

whatnow123 · 09-05-2007, 11:19 PM

Good thread, does anyone have photos of what this looks like on thier truck?

68Stepbed · 09-06-2007, 07:39 AM

Classic Trucks magazine did an article on the Magnaflow kit on a 72 they have been working on. Here is the article.

http://www.classictrucks.com/tech/06...ion/index.html

Alex Hayley · 09-06-2007, 11:46 AM

Are there any 3" systems sold?

chevydog66 · 09-06-2007, 03:24 PM

Kewl, I do have a GMC truck with rear leaf springs, but I am switching it all over to a 71 Chevy frame, when I decide to do the body off restoration.

bayer20 · 09-06-2007, 07:56 PM

im confused why people want to spent double the amount on pre-bend exhaust systems, just so they can say I have a borla or magnaflow systems. I wonder If Dale jr. buys his system out of a catalog as well? It doesn't matter who makes it, what matters is the diameter of the Pipe and what mufflers you install. A full custom 3in installed system will cost your at a reputable Muffler/Fab shop $250-300 plus Flowmasters. Now with the saved money you can buy yourself a nice camshaft for that extra 40 hp

Jim_PA · 09-06-2007, 10:29 PM

Quote:

Originally Posted by bayer20

im confused why people want to spent double the amount on pre-bend exhaust systems, just so they can say I have a borla or magnaflow systems. I wonder If Dale jr. buys his system out of a catalog as well? It doesn't matter who makes it, what matters is the diameter of the Pipe and what mufflers you install. A full custom 3in installed system will cost your at a reputable Muffler/Fab shop $250-300 plus Flowmasters. Now with the saved money you can buy yourself a nice camshaft for that extra 40 hp

The magnaflow stainless kit sells on ebay for 480 (or best offer on some of them!) and most offer free shipping. The polished stainless mufflers are included.

So... pay an exhaust shop 300 + buy your own mufflers = $400?

For an extra 80 you get a stainless exhaust system, an x-pipe, and an over-the-axle exhaust system. That seems like a pretty good deal to me.

1LoC10 · 09-06-2007, 07:58 PM

What would DaleJr. do, thats my motto

Sport/Truck · 09-06-2007, 10:53 PM

Quote:

Originally Posted by 1LoC10

What would DaleJr. do, thats my motto

WWDJD!

s/t

bayer20 · 09-09-2007, 12:32 PM

Quote:

The magnaflow stainless kit sells on ebay for 480 (or best offer on some of them!) and most offer free shipping. The polished stainless mufflers are included.

So... pay an exhaust shop 300 + buy your own mufflers = $400?

For an extra 80 you get a stainless exhaust system, an x-pipe, and an over-the-axle exhaust system. That seems like a pretty good deal to me.

You are comparing Ebay to Oranges? That is best case scenerio and you still need to eighter a pay someone to install it or b lay underneath your vehicle and try to bolt/weld it up! Im talking buying a system at a retail store at retail price not Ebay. My last system I had installed was custom fit to my headers with one chambers, 3in, H pipe, and cut out to one each out of the side of my body panel and I paid a total of $250 and it sounds so mean it will em-barres every Mustang. It also helps to know that the guys at TBI Fabricate anything from custom headers to rolling chassis 5sec drag cars. You just cant get this kinda stuff out of a cookie cutter exhaust system.

bayer20 · 09-09-2007, 12:40 PM

Quote:

Does anyone make a bolt on 2 1/2" exhaust system for our trucks? I prefer mandrel bent over the local exhaust shop bender.

Whats the difference? Does the local muffler shop use pliers to bend em?

Alex Hayley · 09-09-2007, 12:52 PM

Bayer, now you have me curious. What place did you get that job done? Was the pipe stainless steel, aluminized or something else?

Jim_PA · 09-10-2007, 07:50 PM

Quote:

Originally Posted by bayer20

You are comparing Ebay to Oranges? That is best case scenerio and you still need to eighter a pay someone to install it or b lay underneath your vehicle and try to bolt/weld it up! Im talking buying a system at a retail store at retail price not Ebay. My last system I had installed was custom fit to my headers with one chambers, 3in, H pipe, and cut out to one each out of the side of my body panel and I paid a total of $250 and it sounds so mean it will em-barres every Mustang. It also helps to know that the guys at TBI Fabricate anything from custom headers to rolling chassis 5sec drag cars. You just cant get this kinda stuff out of a cookie cutter exhaust system.

Ebay is the first place to go when shopping for anything, and yes, I work on my stuff myself. Last galvanized flowmaster kit I had lasted less than 3 years before it rusted through at the output of the muffler.

I'm sure for 250, it's not half the system the stainless magnaflow kit is.

jfalesi · 09-13-2007, 12:58 AM

Quote:

Originally Posted by Sport/Truck

WWDJD!

s/t

WWDJD for a Klondike bar? That's what I want to know.

chevydog66 · 09-06-2007, 10:23 PM

Because up here in Indiana they salt the roads in the winter, which make sh** rust. Even though I don't drive my truck in the winter, it still sits on a concrete floor and begins to oxidize. Plus it looks better and performs better and lasts longer. I like to do things right the first time.

Jcentsr6 · 09-09-2007, 01:03 PM

www.mandrelbend.com is doing mine this week.
Thank god I live about 10 mins away from this place. Not to many Mandrel benders around

c10crazy · 09-10-2007, 07:42 AM

Quote:

Originally Posted by Jcentsr6

www.mandrelbend.com is doing mine this week.
Thank god I live about 10 mins away from this place. Not to many Mandrel benders around

How much do they charge for a mandrel bent system if you don't mind me asking?. Please post pics.

09-05-2007, 12:32 PM	#1
chevydog66 GM ONLY BABY!!! Join Date: Oct 2003 Location: Fort Wayne, IN. Posts: 1,998	Pre bent exhaust for our trucks? Does anyone make a bolt on 2 1/2" exhaust system for our trucks? I prefer mandrel bent over the local exhaust shop bender. Names like Flowmaster, Magnaflow, Heartbeat, do they make em for our trucks? How well do they fit? __________________ 2 wrongs don't make a right, but 3 lefts do. 66 Chevelle Malibu 406ci, 573hp, 10.99@121mph 96 Chevy Silverado Z71 72 GMC 1500 Super Custom LS 6.0/4L65 on airride http://www.cardomain.com/ride/707879...mc-c-k-pick-up

09-05-2007, 12:38 PM	#2
Jcentsr6 Junior Member Join Date: Jul 2007 Location: Odenton, Md Posts: 552	Re: Pre bent exhaust for our trucks? I am going to the local Mandrel bend shop this week to get my header back system made. I am running hooker headers with flowmaster 44 mufflers attached...then the mandrel benmt stuff out to the side before the rear wheels. I can give you the info once im finished everything...($$ and where to get) __________________ going to sell this one...looking for a SWB project next.

09-05-2007, 12:59 PM	#3
68 P.O.S. Registered User Join Date: Jan 2007 Location: Puyallup, WA Posts: 1,662	Re: Pre bent exhaust for our trucks? Doesn't Magnaflow offer that exact setup? __________________ 72 C10 lwb fleetside -stock 350/350 combo

09-05-2007, 01:06 PM	#4
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,856	Re: Pre bent exhaust for our trucks? I thought Magnaflow's kit went over the axle- all stainless! Jay, I can't wait to get the details/pics! __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

09-05-2007, 01:06 PM	#5
Shock_Me Senior Member Join Date: May 2005 Location: New Brunswick, Canada Posts: 591	Re: Pre bent exhaust for our trucks? Yes Magnaflow has a kit. LMC carries it. Once you get the part number, plug it into an Ebay search. It's sold by a few Ebay sellers. It's made for longbeds, but can be cut down for shortbeds. Pete

09-05-2007, 01:36 PM	#7
JameslovesJammie God Bless Mr. T Join Date: Apr 2004 Location: Minot, ND Posts: 348	Re: Pre bent exhaust for our trucks? The Magnaflow setup is for coil spring only, but I don't remember why. I'll look in old emails from them and find out. IMHO, it's one heck of a deal. It sells for ~$500 through Summit. Their Dyno showed a 10 HP and 22 lb/ft gain in torque. It's an all stainless, mandrel bent kit. Great product! http://www.magnaflow.com/02product/dynos/c1020.jpg http://www.magnaflow.com/02product/s...e=Trucks&id=76 __________________ Like a midget at a urinal...sometimes you must stay on your toes.

09-05-2007, 04:22 PM	#8
70GMCer Senior Member Join Date: Apr 2005 Location: Joppa, Maryland Posts: 4,408	Re: Pre bent exhaust for our trucks? From Summit.........and a about $150.00 cheaper http://store.summitracing.com/partde...5&autoview=sku __________________ 1997 GMC Sierra Ext 1965 Mustang Last edited by 70GMCer; 09-05-2007 at 04:23 PM.

09-05-2007, 08:22 PM	#9
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: Pre bent exhaust for our trucks? It looks like it would fit nice. 70c10, any pics yet? Can't wait to see them. __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

09-05-2007, 11:19 PM	#10
whatnow123 Registered User Join Date: Oct 2006 Location: Arizona Posts: 835	Re: Pre bent exhaust for our trucks? Good thread, does anyone have photos of what this looks like on thier truck? __________________ 67 Short Step, 355, 700R 4.11 posi rear, 4/6 drop Discs on all 4 corners. Build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=219094

09-06-2007, 07:39 AM	#11
68Stepbed Registered User Join Date: Mar 2005 Location: 10-Uh-See Posts: 5,609	Re: Pre bent exhaust for our trucks? Classic Trucks magazine did an article on the Magnaflow kit on a 72 they have been working on. Here is the article. http://www.classictrucks.com/tech/06...ion/index.html __________________ Matt 68 C10 stepside, LS1/700R4, TCI Engineering suspension system Last edited by 68Stepbed; 09-06-2007 at 07:42 AM.

09-06-2007, 11:46 AM	#12
Alex Hayley Registered User Join Date: Jul 2000 Location: NC Posts: 987	Re: Pre bent exhaust for our trucks? Are there any 3" systems sold?

09-06-2007, 03:24 PM	#13
chevydog66 GM ONLY BABY!!! Join Date: Oct 2003 Location: Fort Wayne, IN. Posts: 1,998	Re: Pre bent exhaust for our trucks? Kewl, I do have a GMC truck with rear leaf springs, but I am switching it all over to a 71 Chevy frame, when I decide to do the body off restoration. __________________ 2 wrongs don't make a right, but 3 lefts do. 66 Chevelle Malibu 406ci, 573hp, 10.99@121mph 96 Chevy Silverado Z71 72 GMC 1500 Super Custom LS 6.0/4L65 on airride http://www.cardomain.com/ride/707879...mc-c-k-pick-up

09-06-2007, 07:56 PM	#14
bayer20 Registered User Join Date: Apr 2007 Location: Fayetteville, NC Posts: 83	Re: Pre bent exhaust for our trucks? im confused why people want to spent double the amount on pre-bend exhaust systems, just so they can say I have a borla or magnaflow systems. I wonder If Dale jr. buys his system out of a catalog as well? It doesn't matter who makes it, what matters is the diameter of the Pipe and what mufflers you install. A full custom 3in installed system will cost your at a reputable Muffler/Fab shop $250-300 plus Flowmasters. Now with the saved money you can buy yourself a nice camshaft for that extra 40 hp __________________ There is no replacement for displacement!

09-06-2007, 07:58 PM	#16
1LoC10 Insert Title Here Join Date: Feb 2006 Location: Dyer, Indiana Posts: 5,679	Re: Pre bent exhaust for our trucks? What would DaleJr. do, thats my motto __________________ BOBBY _69 SWB_ 1000 pics of 67-72's>> http://s193.photobucket.com/albums/z...-72/?start=all <<

09-09-2007, 12:52 PM	#20
Alex Hayley Registered User Join Date: Jul 2000 Location: NC Posts: 987	Re: Pre bent exhaust for our trucks? Bayer, now you have me curious. What place did you get that job done? Was the pipe stainless steel, aluminized or something else?



Register or Log In To remove these advertisements.

09-06-2007, 10:23 PM	#23
chevydog66 GM ONLY BABY!!! Join Date: Oct 2003 Location: Fort Wayne, IN. Posts: 1,998	Re: Pre bent exhaust for our trucks? Because up here in Indiana they salt the roads in the winter, which make sh** rust. Even though I don't drive my truck in the winter, it still sits on a concrete floor and begins to oxidize. Plus it looks better and performs better and lasts longer. I like to do things right the first time. __________________ 2 wrongs don't make a right, but 3 lefts do. 66 Chevelle Malibu 406ci, 573hp, 10.99@121mph 96 Chevy Silverado Z71 72 GMC 1500 Super Custom LS 6.0/4L65 on airride http://www.cardomain.com/ride/707879...mc-c-k-pick-up Last edited by chevydog66; 09-06-2007 at 10:25 PM.

09-09-2007, 01:03 PM	#24
Jcentsr6 Junior Member Join Date: Jul 2007 Location: Odenton, Md Posts: 552	Re: Pre bent exhaust for our trucks? www.mandrelbend.com is doing mine this week. Thank god I live about 10 mins away from this place. Not to many Mandrel benders around __________________ going to sell this one...looking for a SWB project next. Last edited by Jcentsr6; 09-09-2007 at 01:04 PM.

Register or Log In To remove these advertisements.