What wheel studs - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Super73 · 01-29-2008, 02:01 PM

I'm assuming I have a later truck rear as it's a 5x5 patern. Anyone know what rear wheels studs are needed? Snap one and want to replace with like ARP or something else legal.

djracer · 01-30-2008, 12:14 AM

I would go to a 1/2 inch long stud and open ended lug nut. Some of them screw in from the rear of the axle. Just check Jeg's or Summit.

Super73 · 01-30-2008, 02:21 AM

I was going to go with press in's. Any idea regards to the knurl size? I have 1/2-20's right now, but like you mentioned I want to go open shank style.

Outlaw72 · 01-30-2008, 05:47 AM

Super I am currently shopping for the same thing and here is what I have found so far. I am also 5x5 1/2x20 thread.

I knocked one of my wheel studs out just over the weekend and it measures .524 on the knurl. The smallest stud I can find has a .530 knurl and the length is the same as this one. I too am going to a longer stud. So, I'm gunna buy some studs that have a .560-.565 knurl and just trim the axle a bit if that knurl is too large to pop the cherry

djracer · 01-30-2008, 07:03 AM

go here and scope out the 8138's

http://www.moserengineering.com/Page...heelstuds.html

Outlaw72 · 01-30-2008, 09:23 AM

Quote:

Originally Posted by djracer

go here and scope out the 8138's

http://www.moserengineering.com/Page...heelstuds.html

Those may work for Super.

Me.....I'm looking for something that's 2" in length minimum.

71Dragtruck · 01-30-2008, 09:32 AM

If you guys are going to run Weld draglites your going to need 3" studs and the really long shank nuts.

71Dragtruck · 01-30-2008, 09:35 AM

Here's what I'm going to run in my new 9".

djracer · 01-30-2008, 12:50 PM

Quote:

Originally Posted by 71Dragtruck

Here's what I'm going to run in my new 9".

That's what I got in my junk!

Super73 · 01-30-2008, 12:03 PM

Might be able to get these in..

http://store.summitracing.com/partde...5&autoview=sku

Outlaw72 · 01-31-2008, 12:53 AM

Quote:

Originally Posted by Super73

Might be able to get these in..

http://store.summitracing.com/partde...5&autoview=sku

I think those are the ones I am going to buy also...

bigjimzlll · 01-31-2008, 06:46 AM

Those will need massaging. I actually ground a little off of the start of the knurl and forced them in. You will surprised hom much needs to be removed.

01-29-2008, 02:01 PM	#1
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	What wheel studs I'm assuming I have a later truck rear as it's a 5x5 patern. Anyone know what rear wheels studs are needed? Snap one and want to replace with like ARP or something else legal.

01-30-2008, 12:14 AM	#2
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: What wheel studs I would go to a 1/2 inch long stud and open ended lug nut. Some of them screw in from the rear of the axle. Just check Jeg's or Summit. __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

01-30-2008, 02:21 AM	#3
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: What wheel studs I was going to go with press in's. Any idea regards to the knurl size? I have 1/2-20's right now, but like you mentioned I want to go open shank style.

01-30-2008, 05:47 AM	#4
Outlaw72 Hay Team!! Join Date: Jun 2003 Location: Ft. Worth, TX, USA Posts: 366	Re: What wheel studs Super I am currently shopping for the same thing and here is what I have found so far. I am also 5x5 1/2x20 thread. I knocked one of my wheel studs out just over the weekend and it measures .524 on the knurl. The smallest stud I can find has a .530 knurl and the length is the same as this one. I too am going to a longer stud. So, I'm gunna buy some studs that have a .560-.565 knurl and just trim the axle a bit if that knurl is too large to pop the cherry __________________ 1972 Chevrolet Cheyenne LWB "Orange and White" 8) Last edited by Outlaw72; 01-30-2008 at 05:48 AM.

01-30-2008, 07:03 AM	#5
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: What wheel studs go here and scope out the 8138's http://www.moserengineering.com/Page...heelstuds.html __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

01-30-2008, 09:32 AM	#7
71Dragtruck Registered User Join Date: Jun 2004 Location: Saskatchewan, Canada Posts: 1,368	Re: What wheel studs If you guys are going to run Weld draglites your going to need 3" studs and the really long shank nuts. __________________ Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs

01-30-2008, 09:35 AM	#8
71Dragtruck Registered User Join Date: Jun 2004 Location: Saskatchewan, Canada Posts: 1,368	Re: What wheel studs Here's what I'm going to run in my new 9". Attached Images __________________ Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs

01-30-2008, 12:03 PM	#10
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: What wheel studs Might be able to get these in.. http://store.summitracing.com/partde...5&autoview=sku Last edited by Super73; 01-30-2008 at 12:04 PM.

01-31-2008, 06:46 AM	#12
bigjimzlll Senior Member Join Date: Dec 2001 Location: Redding,CA...USA Posts: 4,736	Re: What wheel studs Those will need massaging. I actually ground a little off of the start of the knurl and forced them in. You will surprised hom much needs to be removed. __________________ It's called "drag racing" if they called it "tic..tic..WHAM!..BANG! F*&K!!!", they'd have to keep the magazines under the counter with the other men's publications click the clicky to join the site.... http://67-72chevytrucks.com/vboard/payments.php 67 lwb..first hotrod in 25 years..540 best ET is 9.45 @ 141.44 Anderson,CA



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.