The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


View Poll Results: which carb should i get for my 462 BB
edelbrock 850 qjet 14 56.00%
holly dual feed double pumper 10 40.00%
stop asking for advice so i can learn from my mistakes 1 4.00%
Voters: 25. You may not vote on this poll

Reply
 
Thread Tools Display Modes
Old 11-08-2002, 09:39 PM   #1
>X<
registered IWATA user
 
>X<'s Avatar
 
Join Date: Feb 2002
Location: Baton Rouge
Posts: 4,481
Poll: double pumper or qjet?

aaaarggggghhh!!!! everyone i ask that knows what there talking about says something different! 462 with 292 cam, dont care about gas mileage. i was so close to ordering a 850 qjet, then at work i was talkin gto a guy that builds the diesels for the trackmobiles that we build and he has built a couple 11 secind cars, his current an elcamino, and he says get a dual feeddouble pumper 850, volume is best for my motor??
__________________
-'63 Ford Fairlane 500 coupe, v8, auto, faded and rusty. awaiting built roller 302 and some flat black
-'99 Honda Prelude. vtech/5spd. no pipe, no intake, bone stock. awaiting new top end.
-01 GMC Yukon SLT 5.3 dented and scratched with a noisy tranny.

Take off that Von Dutch hat before i stab you with a 000 Mack.
>X< is offline   Reply With Quote
Old 11-08-2002, 09:49 PM   #2
crazy longhorn
Fabricate till you "puke"
 
Join Date: Jun 2002
Location: Ill
Posts: 9,402
For your combo, Id go with the Holley dp......I would think 800 cfm would be enough, unless you plan a strip only deal. good luck
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....
crazy longhorn is offline   Reply With Quote
Old 11-08-2002, 10:25 PM   #3
mooneyes
Registered User
 
mooneyes's Avatar
 
Join Date: Jan 2002
Location: Slippery Rock PA USA
Posts: 1,692
i agree with crazy longhorn..if performance is what u want go with the d.p.
__________________
Ken Lyons, Slippery rock pa
68 short step 327 t10 4 gear
72 2wd blazer project
70 lwb 305/700r driver
78 caprice project
02 cavalier D.D ( hate it!!)
mooneyes is offline   Reply With Quote
Old 11-08-2002, 11:40 PM   #4
>X<
registered IWATA user
 
>X<'s Avatar
 
Join Date: Feb 2002
Location: Baton Rouge
Posts: 4,481
thanks guys, i want the most possible hp so i'm gonna go with the 850. i dont know where i got "dual feed" from, what is the diff? is a double pumper a dual feed? so i should order the "classic double pumper, 850 CFM classic carb, 429.95"
one more question, which intake manifold do i get to go with this, i am going with the performer rpm, but do i get the spreadbore or oval port? is the dp a spreadbore? whats ths diff between the spreadbore intake and the oval? thanks, sean
__________________
-'63 Ford Fairlane 500 coupe, v8, auto, faded and rusty. awaiting built roller 302 and some flat black
-'99 Honda Prelude. vtech/5spd. no pipe, no intake, bone stock. awaiting new top end.
-01 GMC Yukon SLT 5.3 dented and scratched with a noisy tranny.

Take off that Von Dutch hat before i stab you with a 000 Mack.
>X< is offline   Reply With Quote
Old 11-08-2002, 11:51 PM   #5
flyin99
creator of kong
 
flyin99's Avatar
 
Join Date: Mar 2001
Location: Kentucky
Posts: 538
most double pumpers are dual feed......that means it has 2 fuel inlets..I know you have seen those chrome lines that go to the front and back bowls on the carbs.........that is dual feed........a quadrajet would be a single feed.......just has the one fuel inlet.........the Holley 6210 and a few other quad replacements are double pumpers, but have a single inlet, for ease of use and fit.........as for size.800 should be fine.........mine is a 750 and I have pretty much the same thing as you, except Merlin heads on mine ....hope this helps

As far as intakes....spread bore is the pattern for carbs, such as a quad..small primaries and large secondaries...........all you need is a square bore for a Dbl. pumper holley..........the oval/square port thing, depends on what heads you have.............

Last edited by flyin99; 11-08-2002 at 11:54 PM.
flyin99 is offline   Reply With Quote
Old 11-09-2002, 01:14 AM   #6
bigjimzlll
Senior Member
 
bigjimzlll's Avatar
 
Join Date: Dec 2001
Location: Redding,CA...USA
Posts: 4,736
Id do the double pumper...I used to have a 780...mechanical secondary..very nice..just a little tricky to fine tune
__________________
It's called "drag racing" if they called it "tic..tic..WHAM!..BANG! F*&K!!!", they'd have to keep the magazines under the counter with the other men's publications

click the clicky to join the site....
http://67-72chevytrucks.com/vboard/payments.php


67 lwb..first hotrod in 25 years..540 best ET is 9.45 @ 141.44
Anderson,CA
bigjimzlll is offline   Reply With Quote
Old 11-09-2002, 01:27 AM   #7
nate68
Registered User
 
Join Date: Jan 2000
Location: ca
Posts: 1,110
Holley Double Pumper if you really dont care about mileage. can i borrow it when i go to the track?
__________________
68 short step, 406/700r4, 9" w/discs.
nate68 is offline   Reply With Quote
Old 11-09-2002, 03:36 AM   #8
Hooter
My other Love
 
Hooter's Avatar
 
Join Date: Aug 2001
Location: Castlegar B.C. Canada
Posts: 4,085
holley double pumper is the way to go!
__________________




Castlegar B.C.The great white North (Canada Eh!)
Hooter_5@hotmail.com
First generation Monte Carlo club
pictures of my life
Hooter is offline   Reply With Quote
Old 11-09-2002, 09:48 AM   #9
Randy70C-10
Account Suspended
 
Randy70C-10's Avatar
 
Join Date: Mar 2001
Location: Virginia Beach, Va. U.S.A.
Posts: 15,320
Sorry, I voted for "Stop asking questions". There wasn't a "Dominator" option. It's the best carburetor I've ran by far.
Randy70C-10 is offline   Reply With Quote
Old 11-09-2002, 12:13 PM   #10
crazy longhorn
Fabricate till you "puke"
 
Join Date: Jun 2002
Location: Ill
Posts: 9,402
Randy, thats a cool "carb spacer" you have under that dominator
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....
crazy longhorn is offline   Reply With Quote
Old 11-11-2002, 07:58 PM   #11
Randy70C-10
Account Suspended
 
Randy70C-10's Avatar
 
Join Date: Mar 2001
Location: Virginia Beach, Va. U.S.A.
Posts: 15,320
Thanks! You won't see another one like it. Nobody makes a carb-to-blower plate for a single dominator. That one was milled by my friend "Bob Manning" of Bobs blower drives. He did the fuel lines and distribution block as well.
Randy70C-10 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:34 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com