Aluminum 3 gage bezel - The 1947 - Present Chevrolet & GMC Truck Message Board Network

mekdad · 11-25-2008, 05:58 PM

$35.00 shipped to your door. These fit in the radio hole in a cut up dash.Yes you can cut your dash just to put these in

.They also come with mounting hard ware (8-32 screws and washers),and mount from the back so you cant see them.

They fit 2 inch gages, The holes are 2.065

**lks dcvn** · 11-25-2008, 06:32 PM

Wow - those are nice!

mekdad · 11-26-2008, 12:45 AM

Thanks ttt

Arad68 · 11-26-2008, 12:54 AM

Will it fit over a single DIN cutout?

mekdad · 11-26-2008, 12:58 AM

It is 9.75 wide 2.625 tall out side dimensions.

mekdad · 11-27-2008, 01:15 AM

ttt

NWD02 · 11-27-2008, 01:25 AM

PM being sent.

mekdad · 12-01-2008, 04:08 PM

ttt

NWD02 · 12-01-2008, 11:39 PM

Did you get the email i sent of the a/c control template?

mekdad · 12-01-2008, 11:55 PM

Yes I got it,and yes I can do that.Check your spam filter I thought I sent an e-mail back.

Arad68 · 12-02-2008, 02:35 AM

Might be a dumb question, but will 2 1/16" Autometer guages fit? I think they will, just want to be sure. I would like to put this bezel over the hole of my ashtray. I have no use for the ash tray.

mekdad · 12-02-2008, 10:23 AM

I will try to find out,and get back to you.

mekdad · 12-03-2008, 01:07 AM

ttt

mekdad · 12-05-2008, 03:54 PM

Friday bump

mike nutt · 12-21-2008, 09:29 AM

what is the size of the hole for the guages? how about the same piece that will fit the a/c -heater controls hole?

NWD02 · 12-21-2008, 10:07 AM

Mike, he's working on one for me to work with my vintage air servo 4 knob controls.

72BLUZ · 12-21-2008, 07:41 PM

i like it, will contact you shortly

Senator350 · 12-22-2008, 10:34 AM

anything you can do to put gauges where the heat controls are? PM me

mekdad · 12-22-2008, 03:02 PM

Quote:

Originally Posted by mike nutt

what is the size of the hole for the guages? how about the same piece that will fit the a/c -heater controls hole?

Quote:

Originally Posted by Senator350

anything you can do to put gauges where the heat controls are? PM me

Yes, I am working on a piece that will cover the ignition switch heater controls and cig lighter holes,that will have a new ignition bezel and plug for the lighter hole so you can use it or have it covered.The first one will have a hole for the Vinage air controls then I will make one that will hold 2 1/16gadges.

2 Many Toys · 12-29-2008, 03:56 PM

Quote:

Originally Posted by mekdad

Yes, I am working on a piece that will cover the ignition switch heater controls and cig lighter holes,that will have a new ignition bezel and plug for the lighter hole so you can use it or have it covered.The first one will have a hole for the Vinage air controls then I will make one that will hold 2 1/16gadges.

Any time frame on that piece?

mekdad · 12-29-2008, 04:15 PM

Quote:

Originally Posted by 2 Many Toys

Any time frame on that piece?

Not yet,I am hoping to get to it this week.I was asked about putting a radio hole in that same spot,But I got looking at it,and I don't think there is room,there is some ducting for the defrost vents that is in the way.

VA72C10 · 01-07-2009, 11:16 PM

Quote:

Originally Posted by mekdad

Not yet,I am hoping to get to it this week.I was asked about putting a radio hole in that same spot,But I got looking at it,and I don't think there is room,there is some ducting for the defrost vents that is in the way.

Any updates?

2 Many Toys · 02-03-2009, 04:02 PM

Quote:

Originally Posted by 2 Many Toys

Any time frame on that piece?

Any update on this particular piece?

mekdad · 02-03-2009, 04:26 PM

I have made some.The one for 67 is done,but I am still working out the details on the 68-72.That one is proving to be a PIA with the big ignition and cig lighter bezels.Here are some preview pics and the one I am doing for NWD02 and his a/c controls.

rustyg · 02-05-2009, 03:41 PM

I'll take one of the four that you have if there are any left.
let me know.

11-25-2008, 05:58 PM	#1
mekdad Registered User Join Date: May 2008 Location: Filer, Idaho Posts: 416	Aluminum 3 gage bezel $35.00 shipped to your door. These fit in the radio hole in a cut up dash.Yes you can cut your dash just to put these in .They also come with mounting hard ware (8-32 screws and washers),and mount from the back so you cant see them.They fit 2 inch gages, The holes are 2.065 Attached Images __________________ you never know what you can do until you have to undo something you have done! Last edited by mekdad; 11-25-2008 at 06:01 PM.

11-25-2008, 06:32 PM	#2
lks dcvn Registered User Join Date: Jan 2007 Location: Columbus, Ohio Posts: 4,348	Re: Aluminum 3 gage bezel Wow - those are nice!

11-26-2008, 12:45 AM	#3
mekdad Registered User Join Date: May 2008 Location: Filer, Idaho Posts: 416	Re: Aluminum 3 gage bezel Thanks ttt __________________ you never know what you can do until you have to undo something you have done!

11-26-2008, 12:54 AM	#4
Arad68 Trucks N Tranzams Join Date: Dec 2002 Location: North Las Vegas, Nevada Posts: 816	Re: Aluminum 3 gage bezel Will it fit over a single DIN cutout? __________________ Don '68 Chevy LB 383 TH400/GV/373 posi '56 Chevy 4WD SWB '64 Chevy short stepside '79 Trans Am 455/TH2004R/12blt/4whldisc 95 Kia (Wifes car) 2002 S-10 extended cab pickup "God punishes small sins immediately" Last edited by Arad68; 11-26-2008 at 12:54 AM. Reason: ?

11-26-2008, 12:58 AM	#5
mekdad Registered User Join Date: May 2008 Location: Filer, Idaho Posts: 416	Re: Aluminum 3 gage bezel It is 9.75 wide 2.625 tall out side dimensions. __________________ you never know what you can do until you have to undo something you have done!

11-27-2008, 01:15 AM	#6
mekdad Registered User Join Date: May 2008 Location: Filer, Idaho Posts: 416	Re: Aluminum 3 gage bezel ttt __________________ you never know what you can do until you have to undo something you have done!

11-27-2008, 01:25 AM	#7
NWD02 Registered User Join Date: Oct 2007 Location: Mont Belvieu, Texas Posts: 729	Re: Aluminum 3 gage bezel PM being sent.

12-01-2008, 04:08 PM	#8
mekdad Registered User Join Date: May 2008 Location: Filer, Idaho Posts: 416	Re: Aluminum 3 gage bezel ttt __________________ you never know what you can do until you have to undo something you have done!

12-01-2008, 11:39 PM	#9
NWD02 Registered User Join Date: Oct 2007 Location: Mont Belvieu, Texas Posts: 729	Re: Aluminum 3 gage bezel Did you get the email i sent of the a/c control template?

12-01-2008, 11:55 PM	#10
mekdad Registered User Join Date: May 2008 Location: Filer, Idaho Posts: 416	Re: Aluminum 3 gage bezel Yes I got it,and yes I can do that.Check your spam filter I thought I sent an e-mail back. __________________ you never know what you can do until you have to undo something you have done!

12-02-2008, 02:35 AM	#11
Arad68 Trucks N Tranzams Join Date: Dec 2002 Location: North Las Vegas, Nevada Posts: 816	Re: Aluminum 3 gage bezel Might be a dumb question, but will 2 1/16" Autometer guages fit? I think they will, just want to be sure. I would like to put this bezel over the hole of my ashtray. I have no use for the ash tray. __________________ Don '68 Chevy LB 383 TH400/GV/373 posi '56 Chevy 4WD SWB '64 Chevy short stepside '79 Trans Am 455/TH2004R/12blt/4whldisc 95 Kia (Wifes car) 2002 S-10 extended cab pickup "God punishes small sins immediately"

12-02-2008, 10:23 AM	#12
mekdad Registered User Join Date: May 2008 Location: Filer, Idaho Posts: 416	Re: Aluminum 3 gage bezel I will try to find out,and get back to you. __________________ you never know what you can do until you have to undo something you have done!

12-03-2008, 01:07 AM	#13
mekdad Registered User Join Date: May 2008 Location: Filer, Idaho Posts: 416	Re: Aluminum 3 gage bezel ttt __________________ you never know what you can do until you have to undo something you have done!

12-05-2008, 03:54 PM	#14
mekdad Registered User Join Date: May 2008 Location: Filer, Idaho Posts: 416	Re: Aluminum 3 gage bezel Friday bump __________________ you never know what you can do until you have to undo something you have done!

12-21-2008, 09:29 AM	#15
mike nutt 69fatmotor Join Date: Oct 2005 Location: bama Posts: 660	Re: Aluminum 3 gage bezel what is the size of the hole for the guages? how about the same piece that will fit the a/c -heater controls hole?



Register or Log In To remove these advertisements.

12-21-2008, 10:07 AM	#16
NWD02 Registered User Join Date: Oct 2007 Location: Mont Belvieu, Texas Posts: 729	Re: Aluminum 3 gage bezel Mike, he's working on one for me to work with my vintage air servo 4 knob controls.

12-21-2008, 07:41 PM	#17
72BLUZ Registered User Join Date: Nov 2006 Location: lafayette, ga. Posts: 832	Re: Aluminum 3 gage bezel i like it, will contact you shortly __________________ Freedom is never more than one generation away from extinction. We didn't pass it to our children in the bloodstream. It must be fought for, protected, and handed on for them to do the same.... Ronald Reagan

12-22-2008, 10:34 AM	#18
Senator350 Registered User Join Date: Feb 2004 Location: Albany, NY Posts: 522	Re: Aluminum 3 gage bezel anything you can do to put gauges where the heat controls are? PM me __________________ RN U OVR

02-03-2009, 04:26 PM	#24
mekdad Registered User Join Date: May 2008 Location: Filer, Idaho Posts: 416	Re: Aluminum 3 gage bezel I have made some.The one for 67 is done,but I am still working out the details on the 68-72.That one is proving to be a PIA with the big ignition and cig lighter bezels.Here are some preview pics and the one I am doing for NWD02 and his a/c controls. Attached Images __________________ you never know what you can do until you have to undo something you have done!

02-05-2009, 03:41 PM	#25
rustyg Registered User Join Date: Dec 2003 Location: Gap-Pa. Posts: 186	Re: Aluminum 3 gage bezel I'll take one of the four that you have if there are any left. let me know. __________________ 71 k10 swb 72 k5 72 Burb 4x4 72 GMC Burb 4x4

Register or Log In To remove these advertisements.