20" Coys C-5's (grey) - The 1947 - Present Chevrolet & GMC Truck Message Board Network

SCOTI · 12-15-2008, 11:58 PM

I purchased these earlier in the year for my 68 Beaters rebuild but the city code enforcement crackdowns have caused me to dismantle the project.

They're called C-5's because they fit over Vette C5 rotors & calipers (unlike ARE TT2's). The front wheels are 20x8.5's, 5.25"bs w/255-40-20's. The rears are 20x10's, 5.50"bs w/295-40-20's & they are the 5 on 5 truck bolt pattern. Tires are Toyo Proxes ST's w/about 10-20 miles. They were installed on my 68's rolling chassis for some pics of a C5 big brake kit & then again on my 74 for additional pics & one trip to the local cruise spot & have been stored in my garage since.

I would prefer a local sale so you can personally inspect them which would eliminate any doubts . . ..... $1800 obo. SOLD!

SCOTI · 12-16-2008, 12:00 AM

Here's a pic of a 68 w/the same size tires so you get an idea of how low a truck will go w/them . . ....

**lolife99** · 12-16-2008, 12:09 AM

Good deal for someone close.
What's going to happen with your truck?

SCOTI · 12-16-2008, 12:37 AM

Quote:

Originally Posted by lolife99

Good deal for someone close.
What's going to happen with your truck?

Well.... Of course you already know the wheels/tires are for sale

.

The front fenders & swb bedsides have been bodyworked & primed so they'll get wrapped & stored for future use/bartering. The SBC Dropmember goes on a shelf until summertime & will eventually find its way under my 74 (the C5 brakes will join as well). The frame will get 'tweaked' a little more, my C4 Dropmember will get installed & I'll swap the body from my RestoRod project onto it.

The 350 (out of N2TRUXs' 77) that's mated to a 700r4 along w/the rear 12bolt, & the air aide system will find it's way to another 60's GM truck.

I'm basically forced to put my build in a shop vs. out in my driveway. I figured my RestoRod has been waiting for so long that if I have to pay for any truck getting built @ a shop, it's going to be that one & not a beater.

**lolife99** · 12-16-2008, 12:44 AM

I hate to see the death of your beater. I always liked that truck.

SCOTI · 12-16-2008, 01:42 AM

Quote:

Originally Posted by lolife99

I hate to see the death of your beater. I always liked that truck.

I hate to end the project as well but my other truck is the better investment (for what's left of my sanity @ least). I put the cab/parts in storage so there's always the future.

Quote:

Originally Posted by Spray-Bomb

Wish I had the money for em

They would look good on Killer!

yellowGT · 12-16-2008, 02:35 AM

Im in garland and my brother might be getting those from you.... I think. Just let me hear back from him so see if its a fo' sho thing.

Spray-Bomb · 12-16-2008, 02:42 PM

Quote:

Originally Posted by SCOTI

They would look good on Killer!

I know right

Not that you have the room, but would you be interested in trading for a 67 short step ???

Spray-Bomb · 12-16-2008, 12:59 AM

Wish I had the money for em

sixty8c10 · 12-16-2008, 08:14 AM

im interestested, if i can get my hands on a five lug axle w/ 3.73 gears, or just some five lug axle shafts

LUV2XCLR8 · 12-16-2008, 03:41 PM

Quote:

Originally Posted by sixty8c10

im interestested, if i can get my hands on some five lug axle shafts

I have a set, they came out of a 72 12 bolt rear, PM me.

72BlckButy · 12-16-2008, 09:06 AM

What a deal SCOTI... ttt!

STOCKISH · 12-16-2008, 09:09 AM

Trade ya a $4000 Snap-On plasma to use on your other projects...
It's listed in the classifides if you are interested.

SCOTI · 12-16-2008, 09:35 AM

Quote:

Originally Posted by 1972SuperCheyenne

Trade ya a $4000 Snap-On plasma to use on your other projects...
It's listed in the classifides if you are interested.

Thanks but I've already got a Hobart (Miller). Would be a good trade though

.

STOCKISH · 12-16-2008, 10:14 AM

Cool, thanks man. Let me know if you change your mind.

Chevy_Man · 12-16-2008, 12:20 PM

Well do you have anything in stone yet????? Did you have them on your 68 with the body on at anytime? I was wanting to see what they would look like with my drop....

Eric

SCOTI · 12-16-2008, 12:46 PM

Quote:

Originally Posted by Chevy_Man

Well do you have anything in stone yet????? Did you have them on your 68 with the body on at anytime? I was wanting to see what they would look like with my drop....

Eric

No commitments. I don't have any pics that would help though because when they were installed on the 68, it was just a cab/chassis.

The pics of N2Billets red truck above has the exact same front size (the rears were a little different). In those pics, the truck has 2.5" dropped spindles, air bags, & stock GM style a-arms.

Chevy_Man · 12-16-2008, 01:12 PM

Well what i have is 2 1/2 drop spindles and 2" drop springs in front and 4" springs and 1 1/2" drop blocks in the rear...fleet side bed i was just wondering if there would be any issues at my ride height....

Eric

SCOTI · 12-16-2008, 01:43 PM

Quote:

Originally Posted by Chevy_Man

Well what i have is 2 1/2 drop spindles and 2" drop springs in front and 4" springs and 1 1/2" drop blocks in the rear...fleet side bed i was just wondering if there would be any issues at my ride height....

Eric

Heights would work w/your set-up. I know they worked on the red truck & it was approx +6" drop up front @ ride height.

temogarza48 · 12-16-2008, 02:26 PM

what company makes these rims?

72BlckButy · 12-16-2008, 03:11 PM

Quote:

Originally Posted by temogarza48

what company makes these rims?

These are made by Coy's Wheels.

72BlckButy · 12-16-2008, 03:12 PM

Quote:

Originally Posted by Chevy_Man

Well what i have is 2 1/2 drop spindles and 2" drop springs in front and 4" springs and 1 1/2" drop blocks in the rear...fleet side bed i was just wondering if there would be any issues at my ride height....

Eric

As SCOTI stated, you shouldn't have any issues running these with that setup. Plus he already has the spacers for the caps. Buy them, mount them, and enjoy them...

Chevy_Man · 12-16-2008, 02:32 PM

I just may be interested in them... I sent you a pm with some more questions...

Eric

Chevy_Man · 12-16-2008, 03:23 PM

What do you mean by spacers for the caps?

Eric

71swb4x4 · 12-16-2008, 03:33 PM

Great Deal Scoti!

Quote:

Originally Posted by Chevy_Man

What do you mean by spacers for the caps?

Eric

Eric, he is referring to the spacer between the center cap and the wheel. You can see it on the close-up picture above. Many of Coys wheels have center cap issues on this era of trucks, the center cap on the wheel interferes with the bearing cap on the hub. The little spacer that you see in the picture pushes the wheel center cap out enough so the bearing cap on the rotor will clear.

12-15-2008, 11:58 PM	#1
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,943	20" Coys C-5's (grey) I purchased these earlier in the year for my 68 Beaters rebuild but the city code enforcement crackdowns have caused me to dismantle the project. They're called C-5's because they fit over Vette C5 rotors & calipers (unlike ARE TT2's). The front wheels are 20x8.5's, 5.25"bs w/255-40-20's. The rears are 20x10's, 5.50"bs w/295-40-20's & they are the 5 on 5 truck bolt pattern. Tires are Toyo Proxes ST's w/about 10-20 miles. They were installed on my 68's rolling chassis for some pics of a C5 big brake kit & then again on my 74 for additional pics & one trip to the local cruise spot & have been stored in my garage since. I would prefer a local sale so you can personally inspect them which would eliminate any doubts . . ..... $1800 obo. *SOLD!* Attached Images __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.* Last edited by SCOTI; 12-16-2008 at 11:30 PM.

12-16-2008, 12:00 AM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,943	Re: 20" Coys C-5's (grey) Here's a pic of a 68 w/the same size tires so you get an idea of how low a truck will go w/them . . .... Attached Images __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

12-16-2008, 12:09 AM	#3
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,691	Re: 20" Coys C-5's (grey) Good deal for someone close. What's going to happen with your truck? __________________ Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823

12-16-2008, 12:44 AM	#5
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,691	Re: 20" Coys C-5's (grey) I hate to see the death of your beater. I always liked that truck. __________________ Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823

12-16-2008, 02:35 AM	#7
yellowGT Registered User Join Date: Jan 2006 Location: Garland, TX Posts: 970	Re: 20" Coys C-5's (grey) Im in garland and my brother might be getting those from you.... I think. Just let me hear back from him so see if its a fo' sho thing. __________________ '84 swb chevy '69 swb chevy '68 swb chevy '95 Impala ss-sold '89 chevy crew cab dually 3+3

12-16-2008, 12:59 AM	#9
Spray-Bomb Texas Big Wig Join Date: Jan 2007 Location: Mineola, Texas Posts: 5,620	Re: 20" Coys C-5's (grey) Wish I had the money for em __________________ Just not low enough... ----------------------------- Sinister Killer

12-16-2008, 08:14 AM	#10
sixty8c10 MY EX DRIVES A BROOM Join Date: Nov 2003 Location: Herington, KS Posts: 869	Re: 20" Coys C-5's (grey) im interestested, if i can get my hands on a five lug axle w/ 3.73 gears, or just some five lug axle shafts __________________ They say nobody's perfect. I'm a nobody, so I must be perfect. Building Nemo -1968 C10 Long Bed FRED -1947 KB-2 International

12-16-2008, 09:06 AM	#12
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: 20" Coys C-5's (grey) What a deal SCOTI... ttt! __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

12-16-2008, 09:09 AM	#13
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: 20" Coys C-5's (grey) Trade ya a $4000 Snap-On plasma to use on your other projects... It's listed in the classifides if you are interested. __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

12-16-2008, 10:14 AM	#15
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: 20" Coys C-5's (grey) Cool, thanks man. Let me know if you change your mind. __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

12-16-2008, 12:20 PM	#16
Chevy_Man Tightwad Join Date: Jun 2005 Location: Louisiana Posts: 408	Re: 20" Coys C-5's (grey) Well do you have anything in stone yet????? Did you have them on your 68 with the body on at anytime? I was wanting to see what they would look like with my drop.... Eric __________________ 56 Chevy custom cab step side under construction 55 Chevy 210 68 SWB Stepside back burner under construction 72 Chevy LWB 84 CJ 7 05 Chevy 1500 Crew Cab 30X40 DOGHOUSE(shop) with many add ons

12-16-2008, 01:12 PM	#18
Chevy_Man Tightwad Join Date: Jun 2005 Location: Louisiana Posts: 408	Re: 20" Coys C-5's (grey) Well what i have is 2 1/2 drop spindles and 2" drop springs in front and 4" springs and 1 1/2" drop blocks in the rear...fleet side bed i was just wondering if there would be any issues at my ride height.... Eric __________________ 56 Chevy custom cab step side under construction 55 Chevy 210 68 SWB Stepside back burner under construction 72 Chevy LWB 84 CJ 7 05 Chevy 1500 Crew Cab 30X40 DOGHOUSE(shop) with many add ons

12-16-2008, 02:26 PM	#20
temogarza48 Registered User Join Date: Nov 2008 Location: houston, tx Posts: 64	Re: 20" Coys C-5's (grey) what company makes these rims?

12-16-2008, 02:32 PM	#23
Chevy_Man Tightwad Join Date: Jun 2005 Location: Louisiana Posts: 408	Re: 20" Coys C-5's (grey) I just may be interested in them... I sent you a pm with some more questions... Eric __________________ 56 Chevy custom cab step side under construction 55 Chevy 210 68 SWB Stepside back burner under construction 72 Chevy LWB 84 CJ 7 05 Chevy 1500 Crew Cab 30X40 DOGHOUSE(shop) with many add ons

12-16-2008, 03:23 PM	#24
Chevy_Man Tightwad Join Date: Jun 2005 Location: Louisiana Posts: 408	Re: 20" Coys C-5's (grey) What do you mean by spacers for the caps? Eric __________________ 56 Chevy custom cab step side under construction 55 Chevy 210 68 SWB Stepside back burner under construction 72 Chevy LWB 84 CJ 7 05 Chevy 1500 Crew Cab 30X40 DOGHOUSE(shop) with many add ons



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.