The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 12-19-2008, 12:10 AM   #1
87Lowrider
Navy Radioman Veteran
 
87Lowrider's Avatar
 
Join Date: Jul 2007
Location: Western Kentucky
Posts: 1,356
Mating a '78 Camaro Front Clip on my '57 Stepside?

Hey guys,

I've been slowly rebuilding a '78 Camaro for the past 2 years.

I'm considering scraping the project and using the sub frame for my '57 Stepside.



It has been completely rebuilt with new Energy Suspension bushings, rotors, brakes, motor mounts and shocks. Can the clip be welded to the frame rails of the '57?

Thanks in advance!


Kenny

Last edited by 87Lowrider; 12-19-2008 at 12:13 AM.
87Lowrider is offline   Reply With Quote
Old 12-19-2008, 02:00 AM   #2
Kim57
Registered User
 
Kim57's Avatar
 
Join Date: Aug 2007
Location: Corona, California
Posts: 7,998
Re: Mating a '78 Camaro Front Clip on my '57 Stepside?

Hi Kenny
I'm not sure of the track width on the 78 camaro but if it is the same as or close to the 57 then it can be done. Guys have used the 1st gen sub frames without any problems.
Kim
Kim57 is offline   Reply With Quote
Old 12-19-2008, 12:56 PM   #3
OrrieG
Registered User
 
OrrieG's Avatar
 
Join Date: Jun 2006
Location: Idaho
Posts: 8,800
Re: Mating a '78 Camaro Front Clip on my '57 Stepside?

Yes, there is a guy around here that does it all the time to 57-59's. Uses the front clip and rear end. Do a search there is probably a thread on here showing it. The splice point is a little messy because the camaro frame is not straight and box shaped at the splice.
__________________
1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread
1964 Chevelle Malibu w/ 355-350TH (daily driver)
Helpful AD and TF Manual Site Old Car Manual Project
OrrieG is offline   Reply With Quote
Old 12-19-2008, 01:36 PM   #4
Longstep70
Junior Member
 
Join Date: Jan 2005
Location: San Jose , Ca
Posts: 235
Re: Mating a '78 Camaro Front Clip on my '57 Stepside?

The 2nd gen clip is the better choice over the 1st gen so yes you can do this:
I strongly suggest you read this tech article:

http://www.jalopyjournal.com/forum/s...ht=Camaro+clip

some great stuff in here. I haven't done this yet but Im planning to do this very soon to my 59.

-Andy
Longstep70 is offline   Reply With Quote
Old 12-20-2008, 01:04 PM   #5
87Lowrider
Navy Radioman Veteran
 
87Lowrider's Avatar
 
Join Date: Jul 2007
Location: Western Kentucky
Posts: 1,356
Re: Mating a '78 Camaro Front Clip on my '57 Stepside?

Quote:
Originally Posted by Longstep70 View Post
The 2nd gen clip is the better choice over the 1st gen so yes you can do this:
I strongly suggest you read this tech article:

http://www.jalopyjournal.com/forum/s...ht=Camaro+clip

some great stuff in here. I haven't done this yet but Im planning to do this very soon to my 59.

-Andy
Andy - What a thread!

Lots o info there. Gonna be a while till I get through it.

Thanks!!

Kenny
87Lowrider is offline   Reply With Quote
Old 12-19-2008, 02:03 PM   #6
56chevy1300
Registered User
 
56chevy1300's Avatar
 
Join Date: Dec 2006
Location: Edmonton, Alberta
Posts: 522
Re: Mating a '78 Camaro Front Clip on my '57 Stepside?

You can check out my thread, I installed a 74 Trans Am subframe, same as the 78 Camaro.

http://67-72chevytrucks.com/vboard/s...d.php?t=220256
56chevy1300 is offline   Reply With Quote
Old 12-19-2008, 07:16 PM   #7
87Lowrider
Navy Radioman Veteran
 
87Lowrider's Avatar
 
Join Date: Jul 2007
Location: Western Kentucky
Posts: 1,356
Re: Mating a '78 Camaro Front Clip on my '57 Stepside?

Thanks guys,

I have the rear also but am planning on using my '73 Jag XJ6 IRS for it instead.

Looks like I'm starting back on the truck a little quicker than I had planned. Might even have it on the road in '09.


Kenny
87Lowrider is offline   Reply With Quote
Old 12-20-2008, 01:11 PM   #8
87Lowrider
Navy Radioman Veteran
 
87Lowrider's Avatar
 
Join Date: Jul 2007
Location: Western Kentucky
Posts: 1,356
Re: Mating a '78 Camaro Front Clip on my '57 Stepside?

Quote:
Originally Posted by 56chevy1300 View Post
You can check out my thread, I installed a 74 Trans Am subframe, same as the 78 Camaro.

http://67-72chevytrucks.com/vboard/s...d.php?t=220256
That is one clean install!

ME LIKEY!



Kenny
87Lowrider is offline   Reply With Quote
Old 12-20-2008, 12:32 PM   #9
nuke1
Registered User
 
nuke1's Avatar
 
Join Date: Jun 2007
Location: Saskatoon, Saskatchewan,:
Posts: 2,901
Re: Mating a '78 Camaro Front Clip on my '57 Stepside?

i also installed one in the 58, check my sig, lowered it 7 inches over stock. used a 79 camaro
__________________
James
1968 GMC "HAVOC"
1986 GMC "Frank"
J.J.R.H. Design & Consulting

My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300
A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238
1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361
Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390
Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100
1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587
nuke1 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:07 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com