|
|
|
12-29-2008, 07:25 PM
|
#1 |
|
Registered User
Join Date: Feb 2007
Location: knoxville tn
Posts: 1,013
|
? for dropmember guys
yes i,ve seached. does anyone have pics of there braklines on the front after the dropmember installed thanks
__________________
nickle and dime |
|
|
|
12-29-2008, 10:18 PM
|
#2 |
|
Registered User
Join Date: Aug 2008
Location: Mansfield, TX
Posts: 309
|
Re: ? for dropmember guys
Have you searched? HAHA j/k I'm sure someone will chime in here. I don't have anything on the subject.....
|
|
|
|
|
12-29-2008, 10:36 PM
|
#3 |
|
67-72 parts collector,…
 
Join Date: Nov 2002
Location: Mid-MO
Posts: 22,700
|
Re: ? for dropmember guys
I would imagine you're going to have to bend them up yourself. I don't think anything stock will work.
__________________
Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823 |
|
|
|
|
12-30-2008, 12:03 AM
|
#4 |
|
Registered User
Join Date: Feb 2008
Location: San Antonio, TX.
Posts: 121
|
Re: ? for dropmember guys
hey royo, I'll post some pics 2 morrow, it's kinda late, but if I remember right I didn't have to replace any lines just had to push and pull some.......
__________________
GROUND ZERO IS R LIMIT 
|
|
|
|
|
12-30-2008, 01:09 AM
|
#5 |
|
Senior Member
Join Date: Dec 2003
Location: Mesa,Az
Posts: 3,981
|
Re: ? for dropmember guys
I have bent them up a couple ways:
I have ran them across the Dropmember just like on a factory 63-72 crossmember set-up... and I have ran them across the factory crossmember in front of the Dropmember (that's how the 73-87 lines are ran). It's a bit easier and less hassle bending the lines if you go the 73-87 way.
__________________
www.PorterbuiltFabrication.com Phone: 480-297-2621 E-mail: sales@pbfab.com Find us on FaceBook under Porterbuilt Fabrication Specializing in Chassis and Suspension Components for your Classic Chevrolet Truck. We offer components from the following manufacturers: Porterbuilt Accuair Ridetech (Air Ride Technologies) Air Lift Wilwood Intro Unisteer ECE Gotta Show Air Lift Borgeson CPP Supporting this forum since 2003! |
|
|
|
|
12-30-2008, 02:50 AM
|
#6 |
|
Registered User
Join Date: Feb 2007
Location: knoxville tn
Posts: 1,013
|
Re: ? for dropmember guys
OK then thanks guys. I dont care to replace them I just want to do it one time and be done
__________________
nickle and dime |
|
|
|
|
12-30-2008, 01:06 PM
|
#7 |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,064
|
Re: ? for dropmember guys
I had the lines routed like the 73-87's as mentioned but the frame is now stripped of all that stuff so I can't help w/pics. It did require tweaking the lines on the pass side to route through the frame braces.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
