Shifter Handlle Question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Prathbun · 02-08-2009, 01:40 PM

I have a tilt column ('72) and I have added a Camaro style steering wheel. My shifter handle seems like its way out there. Is there any other options for a shorter shifter handle that would work? Thanks for the help.

66skylarkpost · 02-08-2009, 04:08 PM

i'm not sure .i have a 4 spoke camaro as well in my 70, some years ago i installed a late 70's van tilt and it has a much nicer shorter arm , i'm not sure if they will work in an older column

magsnubby · 02-08-2009, 06:13 PM

Could you shorten it up and rethread the end?

**leddzepp** · 02-08-2009, 06:14 PM

Use a shifter from a van tilt. They are shorter, and work perfectly with a smaller steering wheel.

463 · 02-08-2009, 08:42 PM

you can use a gm car shifter from the 70's and mayby as late as a 1990 caprice car. use a punch and bump the pin up and pull the shift lever out. you may want to grab the spring also.

Prathbun · 02-19-2009, 11:50 PM

Thanks for all the input. This is the type of lever I need. As you can see, this one is almost completely trashed!! I'm having a difficult time locating a van shifter (I think it would look best with my smaller camaro steering wheel). Will I'll need to go to a GM parts counter? Does anyone have any other suggestions??

Thanks for the help!!

Prathbun · 02-21-2009, 03:19 PM

ttt

low'n slow · 02-21-2009, 03:26 PM

Check out the Jeeps in the junkyard as well. They used alot of the same parts.

02-08-2009, 01:40 PM	#1
Prathbun Registered User Join Date: Jul 2007 Location: Poplar Bluff, MO 63901 Posts: 293	Shifter Handlle Question I have a tilt column ('72) and I have added a Camaro style steering wheel. My shifter handle seems like its way out there. Is there any other options for a shorter shifter handle that would work? Thanks for the help. __________________ It's Not Rust, It's Patina!! 1967 C 20 Large Window, 700R4, 283, Tilt, PS, PB.....A Rusty But Trusty Gas Hog 2008 Silverado LTZ 1500 4x4

02-08-2009, 04:08 PM	#2
66skylarkpost Registered User Join Date: Mar 2006 Location: kearney,nebraska Posts: 443	Re: Shifter Handlle Question i'm not sure .i have a 4 spoke camaro as well in my 70, some years ago i installed a late 70's van tilt and it has a much nicer shorter arm , i'm not sure if they will work in an older column __________________ '70 k-10 longbox- mid 70's drivetrain 350/350 487x heads 10.1:1 flowmasters ,35's 3.73's auburn posi ,rear shackle flip. '72 short stepside U.S. forestry truck, '73 455 buick,400 turbo,dropped 2"-4 1/4" ,3.07 posi,:'89 silverado 1500 ,OK truck ,5.7 holley tbi ,trick 700r4 3.07 auburn posi ,and my '66 skylark ,'73 centurion and my '84 monte carlo imca stock car

02-08-2009, 06:13 PM	#3
magsnubby Registered User Join Date: Jan 2007 Location: fresno,ca Posts: 448	Re: Shifter Handlle Question Could you shorten it up and rethread the end?

02-08-2009, 06:14 PM	#4
leddzepp Moderator Join Date: May 2007 Location: Southern Cal Posts: 20,036	Re: Shifter Handlle Question Use a shifter from a van tilt. They are shorter, and work perfectly with a smaller steering wheel.

02-08-2009, 08:42 PM	#5
463 Registered User Join Date: Nov 2007 Location: Sask Canada Posts: 1,666	Re: Shifter Handlle Question you can use a gm car shifter from the 70's and mayby as late as a 1990 caprice car. use a punch and bump the pin up and pull the shift lever out. you may want to grab the spring also. __________________ Trueman

02-19-2009, 11:50 PM	#6
Prathbun Registered User Join Date: Jul 2007 Location: Poplar Bluff, MO 63901 Posts: 293	Re: Shifter Handlle Question Thanks for all the input. This is the type of lever I need. As you can see, this one is almost completely trashed!! I'm having a difficult time locating a van shifter (I think it would look best with my smaller camaro steering wheel). Will I'll need to go to a GM parts counter? Does anyone have any other suggestions?? Thanks for the help!! Attached Images __________________ It's Not Rust, It's Patina!! 1967 C 20 Large Window, 700R4, 283, Tilt, PS, PB.....A Rusty But Trusty Gas Hog 2008 Silverado LTZ 1500 4x4

02-21-2009, 03:19 PM	#7
Prathbun Registered User Join Date: Jul 2007 Location: Poplar Bluff, MO 63901 Posts: 293	Re: Shifter Handlle Question ttt __________________ It's Not Rust, It's Patina!! 1967 C 20 Large Window, 700R4, 283, Tilt, PS, PB.....A Rusty But Trusty Gas Hog 2008 Silverado LTZ 1500 4x4

02-21-2009, 03:26 PM	#8
low'n slow Too Dumb To Know Better Join Date: Nov 2005 Location: Texas Posts: 883	Re: Shifter Handlle Question Check out the Jeeps in the junkyard as well. They used alot of the same parts.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.