Parting out my motor - The 1947 - Present Chevrolet & GMC Truck Message Board Network

5150 · 05-11-2009, 11:07 PM

I got a small knock in it and we think a bearing has spun. It has about 20 miles on it, but I found a smokin' deal on a ZZ4.

I'm going to pull it out this weekend.

Heads-stock 882 cast heads press in studs ....start to finish
stud towers milled off and tapped for 3/8 studs and push rod guides
Z valve springs, and positive valve seals ,1.5 ratio and 3/8" studs, and gm performance valves-$200 plus shipping

Chevrolet "Raised" Letter Valve Covers and breather-$100 plus shipping

Edelbrock Aluminum Intake-$75 plus shipping

.030 over Pistons and Rods-$75 plus shipping

Everything comes with the bolts, rings, or whatever is attached, you can have it also.

I'm not selling the serpentine stuff, I need it for my new motor.

Stuff is for sale locally also.

**thelonerife** · 05-11-2009, 11:33 PM

interested in your intake B. I need to check to see if it will fit my 1972 heads. Wheres Woody at when I need him?lol

5150 · 05-12-2009, 07:13 AM

I forgot to mention, NO PM's. If you are interested post in this thread. I always forget that because I think it's common sense, but....

5150 · 05-12-2009, 04:06 PM

ttt,

The pistons are forged .030 over

Tx Firefighter · 05-12-2009, 04:17 PM

I'd like the intake if it makes it to me. You include the bolts with it too right?

5150 · 05-12-2009, 04:17 PM

Yes, sir you can have them.

Tx Firefighter · 05-12-2009, 04:18 PM

And tell me about the pistons. What is their configuration...4 valve relief, dish with 4 reliefs, what ?

5150 · 05-12-2009, 04:26 PM

Tx,

They are like these:

http://cgi.ebay.com/ebaymotors/Chevy...ht_1637wt_1167

I had to buy one new one because I broke one. I'm trying to sell them with the block, pan, etc. locally. Didn't figure the block would go on the board for anything, but might go locally.

Tx Firefighter · 05-12-2009, 04:31 PM

Very good then. I want the intake unless the guy above me speaks for it. My zip is 76082. I understand you need to pull it out of the truck yet. Just let me know when you're ready to get it sent out and I will get the money over to you.

my67chevytruck · 05-12-2009, 04:35 PM

Bryan, are you selling the serp setup and the exhaust manifolds?

5150 · 05-12-2009, 04:37 PM

no, I need to keep those for the ZZ4

my67chevytruck · 05-12-2009, 04:44 PM

sorry think my network connection blipped on me the 1st time as i did not see you text with pricing, or i would not have asked..... BTTT

5150 · 05-12-2009, 04:46 PM

no problem

70rs/ss · 05-12-2009, 06:26 PM

I like the valve covers, not sure if I can justify the $$$ (price is great, but $$$ is tight here), but I'll see and get back w/ya?

**thelonerife** · 05-13-2009, 09:02 PM

I'll take the intake. Bryan. Bolts too since their included. I'll pick it up.

5150 · 05-13-2009, 10:04 PM

It's yours Chuck

5150 · 05-18-2009, 05:19 PM

txfirefighter, were you interested in the pistons?

Tx Firefighter · 05-18-2009, 08:16 PM

No sir, I've decided to build a stroker instead.

STOCKISH · 05-18-2009, 08:37 PM

How old is the distributor? How much shipped to 27587

sgrier · 05-19-2009, 11:05 AM

How much for shipping on the pistons to 36092.

5150 · 05-19-2009, 11:56 AM

I decided to use the distributor on my ZZ4. It has a distributor with it, if you're interested, but it's not as new as the one I have.

sgrier-pm sent

5150 · 05-31-2009, 11:15 AM

Still have the Valve Covers and Heads

sold the Pistons and Block Parts

stealthy '69 · 06-01-2009, 12:10 AM

How much for the heads with shipping to 68127, probably too much but worth the price to ask.

05-11-2009, 11:07 PM	#1
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Parting out my motor I got a small knock in it and we think a bearing has spun. It has about 20 miles on it, but I found a smokin' deal on a ZZ4. I'm going to pull it out this weekend. Heads-stock 882 cast heads press in studs ....start to finish stud towers milled off and tapped for 3/8 studs and push rod guides Z valve springs, and positive valve seals ,1.5 ratio and 3/8" studs, and gm performance valves-$200 plus shipping Chevrolet "Raised" Letter Valve Covers and breather-$100 plus shipping Edelbrock Aluminum Intake-$75 plus shipping .030 over Pistons and Rods-$75 plus shipping Everything comes with the bolts, rings, or whatever is attached, you can have it also. I'm not selling the serpentine stuff, I need it for my new motor. Stuff is for sale locally also. __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4 Last edited by 5150; 05-11-2009 at 11:10 PM.

05-11-2009, 11:33 PM	#2
thelonerife Senior Member Join Date: Jul 2007 Location: Clarksville TN 37043 Posts: 8,702	Re: Parting out my motor interested in your intake B. I need to check to see if it will fit my 1972 heads. Wheres Woody at when I need him?lol __________________ Chuck 68swb Fleetside build ''Choncho'' http://67-72chevytrucks.com/vboard/s...d.php?t=374892 My trailer redo http://67-72chevytrucks.com/vboard/s...69#post5893869 Chuy my 59 bug http://67-72chevytrucks.com/vboard/s...d.php?t=653798 Putnam 87 GMC Shop truck http://67-72chevytrucks.com/vboard/s...d.php?t=707687 Last edited by thelonerife; 05-11-2009 at 11:36 PM.

05-12-2009, 07:13 AM	#3
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Parting out my motor I forgot to mention, NO PM's. If you are interested post in this thread. I always forget that because I think it's common sense, but.... __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

05-12-2009, 04:06 PM	#4
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Parting out my motor ttt, The pistons are forged .030 over __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

05-12-2009, 04:17 PM	#5
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: Parting out my motor I'd like the intake if it makes it to me. You include the bolts with it too right? __________________ I'm on the Instagram- @Gearhead_Kevin

05-12-2009, 04:17 PM	#6
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Parting out my motor Yes, sir you can have them. __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

05-12-2009, 04:18 PM	#7
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: Parting out my motor And tell me about the pistons. What is their configuration...4 valve relief, dish with 4 reliefs, what ? __________________ I'm on the Instagram- @Gearhead_Kevin

05-12-2009, 04:26 PM	#8
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Parting out my motor Tx, They are like these: http://cgi.ebay.com/ebaymotors/Chevy...ht_1637wt_1167 I had to buy one new one because I broke one. I'm trying to sell them with the block, pan, etc. locally. Didn't figure the block would go on the board for anything, but might go locally. __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

05-12-2009, 04:31 PM	#9
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: Parting out my motor Very good then. I want the intake unless the guy above me speaks for it. My zip is 76082. I understand you need to pull it out of the truck yet. Just let me know when you're ready to get it sent out and I will get the money over to you. __________________ I'm on the Instagram- @Gearhead_Kevin

05-12-2009, 04:35 PM	#10
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: Parting out my motor Bryan, are you selling the serp setup and the exhaust manifolds? __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470

05-12-2009, 04:37 PM	#11
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Parting out my motor no, I need to keep those for the ZZ4 __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

05-12-2009, 04:44 PM	#12
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: Parting out my motor sorry think my network connection blipped on me the 1st time as i did not see you text with pricing, or i would not have asked..... BTTT __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470 Last edited by my67chevytruck; 05-12-2009 at 04:45 PM.

05-12-2009, 04:46 PM	#13
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Parting out my motor no problem __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

05-12-2009, 06:26 PM	#14
70rs/ss Registered User Join Date: Dec 2004 Location: Northern AZ Posts: 7,270	Re: Parting out my motor I like the valve covers, not sure if I can justify the $$$ (price is great, but $$$ is tight here), but I'll see and get back w/ya?

05-13-2009, 09:02 PM	#15
thelonerife Senior Member Join Date: Jul 2007 Location: Clarksville TN 37043 Posts: 8,702	Re: Parting out my motor I'll take the intake. Bryan. Bolts too since their included. I'll pick it up. __________________ Chuck 68swb Fleetside build ''Choncho'' http://67-72chevytrucks.com/vboard/s...d.php?t=374892 My trailer redo http://67-72chevytrucks.com/vboard/s...69#post5893869 Chuy my 59 bug http://67-72chevytrucks.com/vboard/s...d.php?t=653798 Putnam 87 GMC Shop truck http://67-72chevytrucks.com/vboard/s...d.php?t=707687



Register or Log In To remove these advertisements.

05-13-2009, 10:04 PM	#16
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Parting out my motor It's yours Chuck __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

05-18-2009, 05:19 PM	#17
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Parting out my motor txfirefighter, were you interested in the pistons? __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

05-18-2009, 08:16 PM	#18
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: Parting out my motor No sir, I've decided to build a stroker instead. __________________ I'm on the Instagram- @Gearhead_Kevin

05-18-2009, 08:37 PM	#19
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: Parting out my motor How old is the distributor? How much shipped to 27587 __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

05-19-2009, 11:05 AM	#20
sgrier Registered User Join Date: Dec 2007 Location: wetumpka, alabama Posts: 141	Re: Parting out my motor How much for shipping on the pistons to 36092.

05-19-2009, 11:56 AM	#21
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Parting out my motor I decided to use the distributor on my ZZ4. It has a distributor with it, if you're interested, but it's not as new as the one I have. sgrier-pm sent __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

05-31-2009, 11:15 AM	#22
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Parting out my motor Still have the Valve Covers and Heads sold the Pistons and Block Parts __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

06-01-2009, 12:10 AM	#23
stealthy '69 '69 Chevy SWB Join Date: Feb 2009 Location: Surprise, Az Posts: 1,065	Re: Parting out my motor How much for the heads with shipping to 68127, probably too much but worth the price to ask.

Register or Log In To remove these advertisements.