If this rides a rocking don't comma knockin? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

AJLChase · 08-23-2009, 10:13 PM

Well, that's at least what my ride is sounding like right now...like there's some squeeky coils in the hand me down bed...if you get my drift. So, I was first thinking the squeeking sound...which in all honesty is louder then just a squeek was from my shocks. As I'm sure they're pretty old. I went to the part store and without looking at my truck the salesperson suggested it might also be my ball joints needed greased.

So, if it's my shocks...I am pretty sure I can change those on my own...as for the ball joints needing greased..I'm not sure what I would need to do. Are there any guides or tips? I looked in the FAQs and only found tips on removing the A arm and Ball joint.

71swb4x4 · 08-23-2009, 10:46 PM

Some ball joints have a grease zerk on them. Just put the grease gun on and give a couple squirts. Not too much though. While you are under there see if your U-jionts have grease zerks too. There is a whole slew of front end parts that are greaseable. Someone smarter than me will chime in soon.
As far as the squeak, can you have someone bounce the truck while you walk around it and listen?

AJLChase · 08-23-2009, 10:59 PM

Ok, i'm a novice so what is exactly a "zerk" if it's that easy then yes I'll go load up on grease and get a gun and do that tomorrow. I did also have somone rock the truck back and forth and it did sound like it was coming from in side the front left wheel well, but I couldn't narrow it down anymore then that.

Longhorn321 · 08-23-2009, 11:51 PM

Quote:

Originally Posted by AJLChase

Ok, i'm a novice so what is exactly a "zerk" if it's that easy then yes I'll go load up on grease and get a gun and do that tomorrow. I did also have somone rock the truck back and forth and it did sound like it was coming from in side the front left wheel well, but I couldn't narrow it down anymore then that.

A "zerk" is simply a fitting or a "nipple" that you snap the grease gun onto.

*Stitch* · 08-23-2009, 11:42 PM

if you get your oil changed at an oil change grease monkey place, they should grease the chassis and suspension while their down there...you could ask/tell them to do it to make sure...

Chuck.

**N2TRUX** · 08-23-2009, 11:55 PM

Pics are sooo much better for explainations. Look at the fitting on the bottom.

AJLChase · 08-23-2009, 11:58 PM

Quote:

Originally Posted by N2TRUX

Pics are sooo much better for explainations. Look at the fitting on the bottom.

Haha yes I totally agree. I should be able to handle that then. Pretty much just fill it up until it starts oozing out I assume?

**N2TRUX** · 08-24-2009, 12:02 AM

That is correct. You should have several of the located on your front suspension "pivot" points. Pump, ooze, and wipe. Pretty simple process.

AJLChase · 08-24-2009, 12:07 AM

Quote:

Originally Posted by N2TRUX

That is correct. You should have several of the located on your front suspension "pivot" points. Pump, ooze, and wipe. Pretty simple process.

I love you!

**N2TRUX** · 08-24-2009, 08:17 AM

Quote:

Originally Posted by AJLChase

I love you!

Thanks.....I think...

chevy_mike · 08-24-2009, 10:25 AM

Just so you know you got them all, there should be 19 fittings that need to be greased on the front end.

djw32 · 08-24-2009, 03:47 PM

Quote:

Originally Posted by chevy_mike

Just so you know you got them all, there should be 19 fittings that need to be greased on the front end.

19 fittings? Off the top of your head, can you provide a quick list of these? I'm coming up short on finding 19 fittings.

David

chevy_mike · 08-26-2009, 10:53 AM

Quote:

Originally Posted by djw32

19 fittings? Off the top of your head, can you provide a quick list of these? I'm coming up short on finding 19 fittings.

David

Upper and lower ball joints (2 x 2)
Upper and lower A-arm cross shafts (4 x 2)
Inner and outer tie rods (2 x 2)
Idler arm (2)
Pitman arm (1)

2x2+4x2+2x2+2+1=19

djw32 · 08-26-2009, 12:35 PM

Quote:

Originally Posted by chevy_mike

Upper and lower ball joints (2 x 2)
Upper and lower A-arm cross shafts (4 x 2)
Inner and outer tie rods (2 x 2)
Idler arm (2)
Pitman arm (1)

2x2+4x2+2x2+2+1=19

Good call. Thanks for the list.

djw32 · 08-24-2009, 03:49 PM

Quote:

Originally Posted by AJLChase

Well, that's at least what my ride is sounding like right now...like there's some squeeky coils in the hand me down bed...if you get my drift. So, I was first thinking the squeeking sound...which in all honesty is louder then just a squeek was from my shocks. As I'm sure they're pretty old. I went to the part store and without looking at my truck the salesperson suggested it might also be my ball joints needed greased.

So, if it's my shocks...I am pretty sure I can change those on my own...as for the ball joints needing greased..I'm not sure what I would need to do. Are there any guides or tips? I looked in the FAQs and only found tips on removing the A arm and Ball joint.

Is the noise coming from the driver or passenger side?

AJLChase · 08-24-2009, 03:59 PM

Quote:

Originally Posted by djw32

Is the noise coming from the driver or passenger side?

It's coming from the driver side....almost like a creaking. When I drive it keeps making the sound whether I hit big bumps or little bumps...but it is worse with bigger bumps

djw32 · 08-24-2009, 04:23 PM

I had a random tingy metal/pop noise come from the front passenger side suspension area this weekend. If you really push on the front passenger side fender/core support, you can make the noise repeat again and again. Damn this truck gets me frustrated!

I will also try to grease everything down...I hope it helps. Let me know if the grease helps you out.

David

Frizzle Fry · 08-24-2009, 07:20 PM

The sway bar and body mounts can squeak too...

AJLChase · 08-24-2009, 11:14 PM

Think greasing it down solved part of my problem. There's now only a creak when the truck moves side to side.....but that could be from just about anything I'm assuming...but the main problem seems to have gotten fixed..I wasn't able to get to all the zerks because the first grease gun I bought was broke and it had the flexible rubber hose, and the new one didn't.

AJLChase · 08-25-2009, 11:07 PM

Sadness....my truck is back to squeeking. Either I didn't fill it up with enough grease, or it's leaking out or that's just not the problem. But it sounded fine last night and this morning, but driving it home from work it was back to being annoying.

djw32 · 08-26-2009, 12:37 PM

Quote:

Originally Posted by AJLChase

Sadness....my truck is back to squeeking. Either I didn't fill it up with enough grease, or it's leaking out or that's just not the problem. But it sounded fine last night and this morning, but driving it home from work it was back to being annoying.

This sucks. What do you think it could be? When do you hear the noise? Is it on take off, driving at speed, or stopping at a light?

AJLChase · 08-26-2009, 11:58 PM

Quote:

Originally Posted by djw32

This sucks. What do you think it could be? When do you hear the noise? Is it on take off, driving at speed, or stopping at a light?

Yeah, I don't know. I got under there again and re greased the zerks and my best guess is it's a shock that's just had it. So, trial and error.

08-23-2009, 10:13 PM	#1
AJLChase Registered User Join Date: May 2009 Location: Lincoln, NE Posts: 322	If this rides a rocking don't comma knockin? Well, that's at least what my ride is sounding like right now...like there's some squeeky coils in the hand me down bed...if you get my drift. So, I was first thinking the squeeking sound...which in all honesty is louder then just a squeek was from my shocks. As I'm sure they're pretty old. I went to the part store and without looking at my truck the salesperson suggested it might also be my ball joints needed greased. So, if it's my shocks...I am pretty sure I can change those on my own...as for the ball joints needing greased..I'm not sure what I would need to do. Are there any guides or tips? I looked in the FAQs and only found tips on removing the A arm and Ball joint.

08-23-2009, 10:46 PM	#2
71swb4x4 Senior Member Join Date: Nov 2003 Location: Brookings, SD Posts: 10,497	Re: If this rides a rocking don't comma knockin? Some ball joints have a grease zerk on them. Just put the grease gun on and give a couple squirts. Not too much though. While you are under there see if your U-jionts have grease zerks too. There is a whole slew of front end parts that are greaseable. Someone smarter than me will chime in soon. As far as the squeak, can you have someone bounce the truck while you walk around it and listen? __________________ Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs.

08-23-2009, 10:59 PM	#3
AJLChase Registered User Join Date: May 2009 Location: Lincoln, NE Posts: 322	Re: If this rides a rocking don't comma knockin? Ok, i'm a novice so what is exactly a "zerk" if it's that easy then yes I'll go load up on grease and get a gun and do that tomorrow. I did also have somone rock the truck back and forth and it did sound like it was coming from in side the front left wheel well, but I couldn't narrow it down anymore then that.

08-23-2009, 11:42 PM	#5
Stitch Account Suspended Join Date: Jul 2008 Location: Where I come from, it's cornbread and chicken... Posts: 3,122	Re: If this rides a rocking don't comma knockin? if you get your oil changed at an oil change grease monkey place, they should grease the chassis and suspension while their down there...you could ask/tell them to do it to make sure... Chuck.

08-23-2009, 11:55 PM	#6
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: If this rides a rocking don't comma knockin? Pics are sooo much better for explainations. Look at the fitting on the bottom. __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

08-24-2009, 12:02 AM	#8
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: If this rides a rocking don't comma knockin? That is correct. You should have several of the located on your front suspension "pivot" points. Pump, ooze, and wipe. Pretty simple process. __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

08-24-2009, 10:25 AM	#11
chevy_mike Never Ending Projects Join Date: Jul 2006 Location: San Diego, CA Posts: 3,836	Re: If this rides a rocking don't comma knockin? Just so you know you got them all, there should be 19 fittings that need to be greased on the front end. __________________ . 1965 C10 Panel, Tiki Express http://www.67-72chevytrucks.com/vboa...d.php?t=506580 SOLD 1968 Chevy C10, Long, Fleetside, Hot Rod Hauler http://67-72chevytrucks.com/vboard/s...d.php?t=313233 SOLD 1965 Chevy C10, Long, Fleetside, Hot Rod C10 http://67-72chevytrucks.com/vboard/s...d.php?t=415702 SOLD We were given two ears and one mouth for a reason... listen twice as much and speak half as often...

08-24-2009, 04:23 PM	#17
djw32 Registered User Join Date: May 2006 Location: So.Cal Posts: 542	Re: If this rides a rocking don't comma knockin? I had a random tingy metal/pop noise come from the front passenger side suspension area this weekend. If you really push on the front passenger side fender/core support, you can make the noise repeat again and again. Damn this truck gets me frustrated! I will also try to grease everything down...I hope it helps. Let me know if the grease helps you out. David Last edited by djw32; 08-24-2009 at 04:25 PM.

08-24-2009, 07:20 PM	#18
Frizzle Fry Registered User Join Date: Aug 2005 Location: Hillsboro Oregon Posts: 6,449	Re: If this rides a rocking don't comma knockin? The sway bar and body mounts can squeak too...

08-24-2009, 11:14 PM	#19
AJLChase Registered User Join Date: May 2009 Location: Lincoln, NE Posts: 322	Re: If this rides a rocking don't comma knockin? Think greasing it down solved part of my problem. There's now only a creak when the truck moves side to side.....but that could be from just about anything I'm assuming...but the main problem seems to have gotten fixed..I wasn't able to get to all the zerks because the first grease gun I bought was broke and it had the flexible rubber hose, and the new one didn't.

08-25-2009, 11:07 PM	#20
AJLChase Registered User Join Date: May 2009 Location: Lincoln, NE Posts: 322	Re: If this rides a rocking don't comma knockin? Sadness....my truck is back to squeeking. Either I didn't fill it up with enough grease, or it's leaking out or that's just not the problem. But it sounded fine last night and this morning, but driving it home from work it was back to being annoying.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.