The "UnOfficial Rock-a-Chief" Thread.... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**ChiefRocka** · 09-22-2009, 05:30 AM

Well my truck has been sitting for days waiting its turn. I haven't torn into this thing as much as I would like, but I don't want this to turn into a diassembled project that can't be funded and properly put back together.

So, untill then, it will patiently wait its turn.

Everyday I walk past it (to build on the Vette) and look at it as if it was the first day I saw it:
-
-
"What the ?!?!!!!"
-
-
-

-
(photoshop at will...you have my permission)
-

-
-
Although, this past weekend (wife took both kids out of town to grandmas) I stayed home for a childhood buddy's bachelor party (whole nother wild story) and managed to work on the "Rock-a-Chief" (un-official part of thread...named by kids, what the heck ??) despite a day and a half hang-over (man I'm a light weight !)

-
-
So...let's start at the CARB, shall we ??
-
-

**ChiefRocka** · 09-22-2009, 05:47 AM

When I first got the truck to the shop...I did what most people would do and "Let's see how good she runs !!"

Jumped it, and with the old fuel...it did run, but very rich.
-
-
So I pulled the carb off, disassembled it and found this:
-
-

-
The main jet was sitting in the bowl..(talk about a smelly, rich-running on old gas situation) !!
-

-
So the rebuild begins...
-

-

-
I've had this bucket of Berrymans 'Chem-Dip' for years (ever since I can remember)...good stuff...that you can't get anymore (??)
-

-
-
After a few moments....It was pulled out and then pressure washed...
-

-

-
Paying close attention to certain parts that may need Loctite (like jets

) and the lower base to bowl screws...
-
-

**ChiefRocka** · 09-22-2009, 05:54 AM

-

-
All done..ready to go on...
-

-
-
I wrapped my air-blow gun with a rag, stuck it in the tank, and blew out as much old fuel as I could.....poured that into my 91 Beater Corolla (

)...then in the tank went 5 gallons of fresh fuel.

I cut back the chock cable housing a bit, and cut the cable a bit to clean up the years of ghetto rigging.

She fired right up, and ran pretty smooth..despite an occasional misfire/pop/stumble at idle. Next will be a compression check (yea, I know...remember what your old teacher said..."Check the compression first, to make sure the engine WILL benefit from a tune-up")...

Hey man...the carb needed help anyway !!!

I'm sure the plugs are 'done' anyway...

If all that checks out...next will be int & exh gaskets...and a new fuel line correctly bent and routed !!

62 short step · 09-22-2009, 08:03 AM

Cool! Glad to see you working on it.

rookierodbuilder · 09-22-2009, 08:11 AM

You can still buy chem dip in automotive stores, just not in California.

joe231 · 09-22-2009, 09:00 AM

Nice work John!!!

**Corts60** · 09-22-2009, 09:25 AM

Nice, you have the same thinking I do when it comes to starting a project......Rebuilding the carb is always the first thing I do for some reason.

**Chevy Fleetside** · 09-22-2009, 10:27 AM

I have a gal of chem dip and have had it for years. I wanted to get rid of it but can't just throw it in the garbage. I think I will just keep it around.

**ChiefRocka** · 09-22-2009, 07:05 PM

Just add it to mine !!

70clipped67 · 09-22-2009, 10:03 PM

The chemical dip is now usually known as Aircraft Stripper. Man it is some crazy smelling stuff!! You can't get away from the fumes quick enough. Congrats on the carb rebuild.

joe231 · 09-23-2009, 01:22 AM

Quote:

Originally Posted by 70clipped67

The chemical dip is now usually known as Aircraft Stripper. Man it is some crazy smelling stuff!! You can't get away from the fumes quick enough. Congrats on the carb rebuild.

Is it still acetone?

MacAttack · 09-23-2009, 11:12 AM

Great looking pics - nice detail.

shrunken66stroker · 09-22-2009, 10:20 PM

Those tape lines on the bed look familiar. That's what mine looked like before I CUT IT UP! You know you want to Rocka. Do it.

**ChiefRocka** · 09-22-2009, 10:47 PM

Quote:

Originally Posted by 62 short step

Cool! Glad to see you working on it.

Me too !

Quote:

Originally Posted by rookierodbuilder

You can still buy chem dip in automotive stores, just not in California.

I knew that...but since Cali is my 'world' we cant get it...You wanna ship me some ? I've had that 5 gallon can for years....still potent !!

Quote:

Originally Posted by joe231

Nice work John!!!

Quote:

Originally Posted by Corts60

Nice, you have the same thinking I do when it comes to starting a project......Rebuilding the carb is always the first thing I do for some reason.

Thanks....yeap thats always my first start....process of elimination

Quote:

Originally Posted by 70clipped67

The chemical dip is now usually known as Aircraft Stripper. Man it is some crazy smelling stuff!! You can't get away from the fumes quick enough. Congrats on the carb rebuild.

Really ? Same stuff, huh ?

Quote:

Originally Posted by shrunken66stroker

Those tape lines on the bed look familiar. That's what mine looked like before I CUT IT UP! You know you want to Rocka. Do it.

bubba327 · 09-22-2009, 10:58 PM

Hey Chief, I hear fumes from Berrymans is a cure-all. From S%its- coughs, colds, runny nose and what bit you on the night before.
Good to see progress being made on the "Rock-a-Chief". I think you should find another carb or two to rebuilt and then start looking for a Offenhauser intake. Get some more air and fuel to that Inline 6 so she can SING!! Keep on it.

**Captainfab** · 09-22-2009, 11:46 PM

Glad to see you working on the new ride. No matter how small of a project a carb rebuild may seem to some, it still feels good to make a little progress.

**ChiefRocka** · 09-22-2009, 11:54 PM

Quote:

Originally Posted by bubba327

Hey Chief, I hear fumes from Berrymans is a cure-all. From S%its- coughs, colds, runny nose and what bit you on the night before.
Good to see progress being made on the "Rock-a-Chief". I think you should find another carb or two to rebuilt and then start looking for a Offenhauser intake. Get some more air and fuel to that Inline 6 so she can SING!! Keep on it.

I'd love too....everybody keep there eyes open for me !!!

Frizzle Fry · 09-23-2009, 01:26 PM

Love where you're headed with the tape lines

4dranch · 09-23-2009, 01:55 PM

Nice detail John.
Just like on the Cheif.
Can't wait till you get to Rockin-n-Rollin on "The Replacement"

**ChiefRocka** · 09-23-2009, 11:24 PM

I got a little further on the Vette and had some time for an inspection

:
-
-
While the truck has been sitting, the tranny has been slowly leaking...so now even reverse was out....I sure dislike pushing vehicles.
-
-

-
-
Got it up on the lift for the first time look at the under side:
-

-
The floors directly under your feet need replacement...but the cab mounts, rockers, and the remainder of the floor is perfect !!
-
Here's another shot of the slick flowmaster split exhaust:
-

-
Really dark picture...but this here is a shot of the right rear brake-line...that was disconnected and plugged....Must of been all those one-wheel burnouts that smoked the tranny !!

-

-
More pics hopefully soon...

**ChiefRocka** · 10-05-2009, 06:04 PM

Had some time to work on it a few days ago. Was able to drop that greasy, nasty, leaky tranny.

Found a broken speedo cable, and some stretched e-brake cables.

Man this thing is majorly muddy/greasy underneith....Man, I really wanna drop this frame, but now is not the right time...unfortuneatly.

I've decided to yank the engine and go thru it, just like I did with the SB in the Chief. It seems to be running smooth, so a compresion check first, then a re-seal, then a 'Krylon' rebuild....

I have more pics coming, also going to do another write on a 700R4 behind the sixer. Decide why not, instead of rebuild the PG, I'll throw the overdrive in it.

Anyone know where to get some 'go' parts for this 292 ??

bubba327 · 10-05-2009, 06:48 PM

I have been watching the E-bay auctions, seems to be Offenhauser and Clifford Intakes on there most of the time. I have been told the Sixes will really run nice if dual or triple carbs are installed. And headers too. A local tranny shop told me it was not easy to hook a 700R4 to a multi carb set-up. Heck, anything is possible , some stuff just takes longer to do. Read Leo Santucci's book on building sixes. He does some crazy stuff with Sixes up in the 400-500 HP range. gets into turbos, blowers and nitrous too.

**slepysal** · 10-07-2009, 12:06 AM

chief I might have a line on a Offy intake. I ll keep you posted

*LILRED66* · 10-07-2009, 12:16 AM

Your play-by-play of the carb rebuild is the inspiration I need to do my first one. Thanks for sharing and keep us posted on your progress.

PrerunnerRob · 10-07-2009, 12:53 AM

Sweet! When is it going down about 18"?

09-22-2009, 05:30 AM	#1
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	The "UnOfficial Rock-a-Chief" Thread.... Well my truck has been sitting for days waiting its turn. I haven't torn into this thing as much as I would like, but I don't want this to turn into a diassembled project that can't be funded and properly put back together. So, untill then, it will patiently wait its turn. Everyday I walk past it (to build on the Vette) and look at it as if it was the first day I saw it: - - "What the ?!?!!!!" - - - - (photoshop at will...you have my permission) - - - Although, this past weekend (wife took both kids out of town to grandmas) I stayed home for a childhood buddy's bachelor party (whole nother wild story) and managed to work on the "Rock-a-Chief" (un-official part of thread...named by kids, what the heck ??) despite a day and a half hang-over (man I'm a light weight !) - - So...let's start at the CARB, shall we ?? - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!" Last edited by ChiefRocka; 09-22-2009 at 06:09 AM.

09-22-2009, 05:47 AM	#2
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: The "UnOfficial Rock-a-Chief" Build Thread.... When I first got the truck to the shop...I did what most people would do and "Let's see how good she runs !!" Jumped it, and with the old fuel...it did run, but very rich. - - So I pulled the carb off, disassembled it and found this: - - - The main jet was sitting in the bowl..(talk about a smelly, rich-running on old gas situation) !! - - So the rebuild begins... - - - I've had this bucket of Berrymans 'Chem-Dip' for years (ever since I can remember)...good stuff...that you can't get anymore (??) - - - After a few moments....It was pulled out and then pressure washed... - - - - - Paying close attention to certain parts that may need Loctite (like jets) and the lower base to bowl screws... - - __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!" Last edited by ChiefRocka; 09-22-2009 at 05:51 AM.

09-22-2009, 05:54 AM	#3
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: The "UnOfficial Rock-a-Chief" Build Thread.... - - - - All done..ready to go on... - - - I wrapped my air-blow gun with a rag, stuck it in the tank, and blew out as much old fuel as I could.....poured that into my 91 Beater Corolla ()...then in the tank went 5 gallons of fresh fuel. I cut back the chock cable housing a bit, and cut the cable a bit to clean up the years of ghetto rigging. She fired right up, and ran pretty smooth..despite an occasional misfire/pop/stumble at idle. Next will be a compression check (yea, I know...remember what your old teacher said..."Check the compression first, to make sure the engine WILL benefit from a tune-up")... Hey man...the carb needed help anyway !!! I'm sure the plugs are 'done' anyway... If all that checks out...next will be int & exh gaskets...and a new fuel line correctly bent and routed !! __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!" Last edited by ChiefRocka; 09-22-2009 at 06:13 AM.

09-22-2009, 08:03 AM	#4
62 short step Senior Member Join Date: Aug 2005 Location: Greenwell Springs, Louisiana Posts: 2,882	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Cool! Glad to see you working on it. __________________ www.louisianaclassictruckclub.com 1965 c-10 86 chevy c/k 20

09-22-2009, 08:11 AM	#5
rookierodbuilder Registered User Join Date: Jan 2009 Location: Sharpsburg, Ky. Posts: 110	Re: The "UnOfficial Rock-a-Chief" Build Thread.... You can still buy chem dip in automotive stores, just not in California.

09-22-2009, 09:00 AM	#6
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Nice work John!!! __________________ *CHEVY ONLY*

09-22-2009, 09:25 AM	#7
Corts60 Just here to tinker Join Date: Jun 2008 Location: Holland, MI Posts: 3,697	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Nice, you have the same thinking I do when it comes to starting a project......Rebuilding the carb is always the first thing I do for some reason. __________________ 78 C10 SWB Diesel #1 (wrecked)http://67-72chevytrucks.com/vboard/s...1978+silverado 78 C10 SWB Diesel #2 (sold)http://67-72chevytrucks.com/vboard/s...d.php?t=650751 60 GMC Suburban (sold)http://67-72chevytrucks.com/vboard/s...d.php?t=445526 60 GMC 1000 (sold)http://67-72chevytrucks.com/vboard/showthread.php?t=298235 67 GMC 1500 (sold) http://67-72chevytrucks.com/vboard/s...d.php?t=803695 73 Chevy C20(Daily)http://67-72chevytrucks.com/vboard/s...d.php?t=852767 86 Suburban(summer unit) http://67-72chevytrucks.com/vboard/s...d.php?t=810697 88 Suburban 4x4(sold)

09-22-2009, 10:27 AM	#8
Chevy Fleetside Registered User Join Date: Sep 2006 Location: San Francisco Posts: 4,782	Re: The "UnOfficial Rock-a-Chief" Build Thread.... I have a gal of chem dip and have had it for years. I wanted to get rid of it but can't just throw it in the garbage. I think I will just keep it around. __________________ "A man and his truck, what a beautiful thing" 65 Short Fleetside BBC 65 Long Fleetside 283 3 on the tree for now. my build thread http://www.67-72chevytrucks.com/vboa...d.php?t=259536

09-22-2009, 07:05 PM	#9
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Just add it to mine !! __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

09-22-2009, 10:03 PM	#10
70clipped67 Registered User Join Date: Jul 2009 Location: Evansville, IN Posts: 9	Re: The "UnOfficial Rock-a-Chief" Build Thread.... The chemical dip is now usually known as Aircraft Stripper. Man it is some crazy smelling stuff!! You can't get away from the fumes quick enough. Congrats on the carb rebuild.

09-23-2009, 11:12 AM	#12
MacAttack 283 Drama Queen Join Date: Dec 2004 Location: Surf City, CA Posts: 2,435	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Great looking pics - nice detail. __________________ For about 12 years of my adult life I had a severe speech impediment. My ex-wife never let me get a word in edgewise.

09-22-2009, 10:20 PM	#13
shrunken66stroker Registered User Join Date: Jan 2008 Location: Las Vegas, Nv Posts: 954	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Those tape lines on the bed look familiar. That's what mine looked like before I CUT IT UP! You know you want to Rocka. Do it. __________________ http://67-72chevytrucks.com/vboard/s...54#post3194654

09-22-2009, 10:58 PM	#15
bubba327 HOW long until spring?? Join Date: Mar 2009 Location: Star Idaho Posts: 1,413	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Hey Chief, I hear fumes from Berrymans is a cure-all. From S%its- coughs, colds, runny nose and what bit you on the night before. Good to see progress being made on the "Rock-a-Chief". I think you should find another carb or two to rebuilt and then start looking for a Offenhauser intake. Get some more air and fuel to that Inline 6 so she can SING!! Keep on it. __________________ 69 chevelle convertible 71-C-10 short-wide and low 64 C-10 custom shortbox "Bubba"s Recycling project" Last edited by ChiefRocka; 09-22-2009 at 11:53 PM.

09-22-2009, 11:46 PM	#16
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Glad to see you working on the new ride. No matter how small of a project a carb rebuild may seem to some, it still feels good to make a little progress. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

09-23-2009, 01:26 PM	#18
Frizzle Fry Registered User Join Date: Aug 2005 Location: Hillsboro Oregon Posts: 6,449	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Love where you're headed with the tape lines



Register or Log In To remove these advertisements.

09-23-2009, 01:55 PM	#19
4dranch Shloooooong bed member #2 Join Date: Aug 2008 Location: Millington Tn. Posts: 1,864	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Nice detail John. Just like on the Cheif. Can't wait till you get to Rockin-n-Rollin on "The Replacement" __________________ *David,* Daughters 66 truck: http://67-72chevytrucks.com/vboard/s...d.php?t=484601 Learning to drive a 3 on the tree: http://www.youtube.com/watch?v=CcCMvRgBo1Q

09-23-2009, 11:24 PM	#20
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: The "UnOfficial Rock-a-Chief" Build Thread.... I got a little further on the Vette and had some time for an inspection: - - While the truck has been sitting, the tranny has been slowly leaking...so now even reverse was out....I sure dislike pushing vehicles. - - - - Got it up on the lift for the first time look at the under side: - - The floors directly under your feet need replacement...but the cab mounts, rockers, and the remainder of the floor is perfect !! - Here's another shot of the slick flowmaster split exhaust: - - Really dark picture...but this here is a shot of the right rear brake-line...that was disconnected and plugged....Must of been all those one-wheel burnouts that smoked the tranny !! - - More pics hopefully soon... __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!" Last edited by ChiefRocka; 09-23-2009 at 11:25 PM.

10-05-2009, 06:04 PM	#21
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Had some time to work on it a few days ago. Was able to drop that greasy, nasty, leaky tranny. Found a broken speedo cable, and some stretched e-brake cables. Man this thing is majorly muddy/greasy underneith....Man, I really wanna drop this frame, but now is not the right time...unfortuneatly. I've decided to yank the engine and go thru it, just like I did with the SB in the Chief. It seems to be running smooth, so a compresion check first, then a re-seal, then a 'Krylon' rebuild.... I have more pics coming, also going to do another write on a 700R4 behind the sixer. Decide why not, instead of rebuild the PG, I'll throw the overdrive in it. Anyone know where to get some 'go' parts for this 292 ?? __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

10-05-2009, 06:48 PM	#22
bubba327 HOW long until spring?? Join Date: Mar 2009 Location: Star Idaho Posts: 1,413	Re: The "UnOfficial Rock-a-Chief" Build Thread.... I have been watching the E-bay auctions, seems to be Offenhauser and Clifford Intakes on there most of the time. I have been told the Sixes will really run nice if dual or triple carbs are installed. And headers too. A local tranny shop told me it was not easy to hook a 700R4 to a multi carb set-up. Heck, anything is possible , some stuff just takes longer to do. Read Leo Santucci's book on building sixes. He does some crazy stuff with Sixes up in the 400-500 HP range. gets into turbos, blowers and nitrous too. __________________ 69 chevelle convertible 71-C-10 short-wide and low 64 C-10 custom shortbox "Bubba"s Recycling project"

10-07-2009, 12:06 AM	#23
slepysal Registered User Join Date: Oct 2006 Location: San Jose NOR*CAL Posts: 3,080	Re: The "UnOfficial Rock-a-Chief" Build Thread.... chief I might have a line on a Offy intake. I ll keep you posted __________________ 1960 Apache long bed fleet L6 250 Clifford intake 2 bbl carb. Langdon cast headers with dual exhaust and bellflower tips. T-5 5 speed, power steering and power disc brakes. "Over, Around or through it... "

10-07-2009, 12:16 AM	#24
LILRED66 Account Suspended Join Date: May 2005 Location: Kansas City, KS Posts: 3,906	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Your play-by-play of the carb rebuild is the inspiration I need to do my first one. Thanks for sharing and keep us posted on your progress.

10-07-2009, 12:53 AM	#25
PrerunnerRob Registered User Join Date: Jan 2007 Location: San Jose Posts: 847	Re: The "UnOfficial Rock-a-Chief" Build Thread.... Sweet! When is it going down about 18"?

Register or Log In To remove these advertisements.