rally wheel spinners - The 1947 - Present Chevrolet & GMC Truck Message Board Network

1968aj · 10-09-2009, 11:51 PM

does anybody know where i can get the spinners for a six lug rally wheel? i dont know if anybody makes them if not how about bowtie stickers i can only find the stickers to fit five lug

jbristo67 · 10-09-2009, 11:56 PM

Where did you find the 5 lug stickers

1968aj · 10-10-2009, 12:01 AM

i have seen the 5 lug stickers on ebay i just searched chevy truck rally and found them

cdowns · 10-10-2009, 07:40 AM

to make stickers go to any graphic arts signmaker a good one can make them for reasonable price // just bring a picture or drawing of what you want with measurements//spinner bars you might try wheet vintiques

Longhorn Man · 10-10-2009, 10:18 AM

spinnrs seem to be hit or miss items.
Seems every swap meet I've been to (admitedly, only a few) you could find spinners everywhere dirt cheap. If you go to e bay they are either junk, or quite expensive, and the few catalogs I've seen them in were rather expensive.

SCOTI · 10-10-2009, 11:13 AM

You can use the same spinners that are used for 5-lug Ralleys. They will mount differently though. On 5-lug Ralleys, the spinner will slip over the snout of the cap (some require some clearancing/grinding).

For 6-lug Ralleys, the snout of the cap is a larger diameter than the spinner. You need 4 rear caps as these have the solid end vs. the open end front caps have because of the 4x4 front hubs. There is a centered hole under the sticker of the cap that will center the spinner. The spinner mounts flush to the end of the cap.

You'll also find the hole sizes for the spinner & the center cap are different as well. You can use a rubber grommet in the hole on the 6-lug cap. When you thread the bolt through for the spinner, it will compress the rubber grommet enough to keep the bolt centered (enough so that it's not wobbling all over the place).

Use Loc-Tite on the threads/hardware.

1968aj · 10-10-2009, 05:06 PM

thanks for the help idid not know the same spinners would work on 6 and 5 lug

10-09-2009, 11:51 PM	#1
1968aj Registered User Join Date: Apr 2009 Location: houston texas Posts: 1,438	rally wheel spinners does anybody know where i can get the spinners for a six lug rally wheel? i dont know if anybody makes them if not how about bowtie stickers i can only find the stickers to fit five lug

10-09-2009, 11:56 PM	#2
jbristo67 resident oilfield trash Join Date: Jan 2009 Location: Lubbock TX Posts: 1,465	Re: rally wheel spinners Where did you find the 5 lug stickers __________________ 1967 SWB C10 396/400 factory air factory tach (sadly had to send to a new home) 1986 Honda 70 Fourtrax 1991 Chevrolet K5 blazer 2wd 1982 Mastercraft Pro Star 190 Stars and Stripes 2002 Chevrolet Tahoe 2011 Nissan Armada

10-10-2009, 12:01 AM	#3
1968aj Registered User Join Date: Apr 2009 Location: houston texas Posts: 1,438	Re: rally wheel spinners i have seen the 5 lug stickers on ebay i just searched chevy truck rally and found them

10-10-2009, 07:40 AM	#4
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: rally wheel spinners to make stickers go to any graphic arts signmaker a good one can make them for reasonable price // just bring a picture or drawing of what you want with measurements//spinner bars you might try wheet vintiques __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

10-10-2009, 10:18 AM	#5
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	Re: rally wheel spinners spinnrs seem to be hit or miss items. Seems every swap meet I've been to (admitedly, only a few) you could find spinners everywhere dirt cheap. If you go to e bay they are either junk, or quite expensive, and the few catalogs I've seen them in were rather expensive.

10-10-2009, 11:13 AM	#6
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,943	Re: rally wheel spinners You can use the same spinners that are used for 5-lug Ralleys. They will mount differently though. On 5-lug Ralleys, the spinner will slip over the snout of the cap (some require some clearancing/grinding). For 6-lug Ralleys, the snout of the cap is a larger diameter than the spinner. You need 4 rear caps as these have the solid end vs. the open end front caps have because of the 4x4 front hubs. There is a centered hole under the sticker of the cap that will center the spinner. The spinner mounts flush to the end of the cap. You'll also find the hole sizes for the spinner & the center cap are different as well. You can use a rubber grommet in the hole on the 6-lug cap. When you thread the bolt through for the spinner, it will compress the rubber grommet enough to keep the bolt centered (enough so that it's not wobbling all over the place). Use Loc-Tite on the threads/hardware. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

10-10-2009, 05:06 PM	#7
1968aj Registered User Join Date: Apr 2009 Location: houston texas Posts: 1,438	Re: rally wheel spinners thanks for the help idid not know the same spinners would work on 6 and 5 lug



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.