|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
11-13-2009, 08:50 PM
|
#1 |
|
Registered User
Join Date: Nov 2006
Location: Sun City, Arizona
Posts: 430
|
Factory upper a arm washers, not the shims
Does anyone have a picture of the factory washers that went on before the shims for alignment. I can't remember if there were two for each side or just one. and if it was one, did it just go on the forward most bolt.
(by the way, 1972 c -10) thanks, dan |
|
|
|
11-13-2009, 08:59 PM
|
#2 |
|
Moderator
 
Join Date: May 2007
Location: Southern Cal
Posts: 20,037
|
Re: Factory upper a arm washers, not the shims
There is one on each bolt. i just re-built mine.
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul |
|
|
|
|
11-13-2009, 09:00 PM
|
#3 | |
|
Registered User
Join Date: Nov 2006
Location: Sun City, Arizona
Posts: 430
|
Re: Factory upper a arm washers, not the shims
Quote:
|
|
|
|
|
|
11-14-2009, 11:20 AM
|
#4 | |
|
Moderator
Join Date: May 2007
Location: Southern Cal
Posts: 20,037
|
Re: Factory upper a arm washers, not the shims
Quote:
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul Last edited by leddzepp; 11-14-2009 at 11:23 AM. |
|
|
|
|
|
11-15-2009, 01:16 PM
|
#5 | |
|
Registered User
Join Date: Nov 2006
Location: Sun City, Arizona
Posts: 430
|
Re: Factory upper a arm washers, not the shims
Quote:
|
|
|
|
|
|
11-15-2009, 01:33 PM
|
#6 | |
|
Moderator
Join Date: May 2007
Location: Southern Cal
Posts: 20,037
|
Re: Factory upper a arm washers, not the shims
Quote:
Its all good, hard to keep track of all the responses sometimes on here. Not to my knowledge. The washers first, then the shims, then the control arm shaft. Good luck!
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul Last edited by leddzepp; 11-15-2009 at 01:33 PM. |
|
|
|
|
|
11-13-2009, 10:22 PM
|
#7 |
|
Registered User
Join Date: Jul 2000
Location: NC
Posts: 987
|
Re: Factory upper a arm washers, not the shims
There are two washers per side. One washer on each bolt. The convex side will face the frame.
|
|
|
|
|
11-13-2009, 11:53 PM
|
#8 | |
|
Registered User
Join Date: Nov 2006
Location: Sun City, Arizona
Posts: 430
|
Re: Factory upper a arm washers, not the shims
Quote:
|
|
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
