67-72 steel floor in a 60-66 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

62 short step · 12-18-2009, 02:56 PM

Finally got one, it was a long bed but outlawc and I cut it down to a shortbed. Thanks for your help outlawc!! It fits very good, will have to redrill some holes to bolt it to the bed though. Here are some pics.

SCOTI · 12-18-2009, 03:26 PM

I have mine sitting in storage waiting for the swap. Looks good.... Anything of note that might prevent problems during the swap?

62 short step · 12-18-2009, 04:20 PM

The front bed panel will have to be modified. Since the wood was 3/4 thick, the flange will have to be cut and moved up then welded. I also had to trim this area (in pic) for the sides to fit right. Other than that it wasnt to bad.

joe231 · 12-18-2009, 04:48 PM

Nice work!!!!

62 short step · 12-18-2009, 05:36 PM

Thanks Joe! I need to get some these from mar-k so I can get it bolted up.

GM 58-66 FLEETSIDE INNER WALL REPAIR PANELS

SCOTI · 12-18-2009, 06:09 PM

I'm raising the floor so the front panel is getting modified regardless; I'll watch out for that rear corner now that I'm informed (Thanks!).

I did buy a MarK smooth front panel for the 68 so I might see if it would work as well.

62 short step · 12-18-2009, 06:33 PM

Quote:

Originally Posted by SCOTI

I'm raising the floor so the front panel is getting modified regardless; I'll watch out for that rear corner now that I'm informed (Thanks!).

I did buy a MarK smooth front panel for the 68 so I might see if it would work as well.

I have a 67-72 front panel here and its different at the top in the corners to the 60-66 panels. I thought about using it also.

64shortc10 · 12-18-2009, 06:39 PM

Did the 67-72 bed floor bolt right to the 60-66 frame stock locations?
Thanks
Tony from Norcal

62 short step · 12-18-2009, 06:53 PM

Quote:

Originally Posted by 64shortc10

Did the 67-72 bed floor bolt right to the 60-66 frame stock locations?
Thanks
Tony from Norcal

No it did not. I will have to drill some new holes.

62 short step · 12-18-2009, 11:05 PM

Yeah you should be good!

**Captainfab** · 12-19-2009, 01:47 AM

That looks good......now I just need to find one that isn't beat to crap.

62 short step · 12-19-2009, 09:37 AM

Quote:

Originally Posted by Captainfab

That looks good......now I just need to find one that isn't beat to crap.

Yeah i was lucky, mine wasnt too bad. In the back it was beat up, but after the 8 inches were taken out it took out most of the bad area.

**ChiefRocka** · 12-19-2009, 10:12 AM

Looks good man...thanks for share the info !!

62 short step · 12-19-2009, 11:10 AM

Quote:

Originally Posted by jonzcustomshop

looks nice, did the wheel tubs and sides bolt on , or did you have to drill?

Yes, they will bolt right up.

Quote:

Originally Posted by ChiefRocka

Looks good man...thanks for share the info !!

No problem Chief.

luvbowties · 12-07-2012, 05:42 AM

Quote:

Originally Posted by Captainfab

That looks good......now I just need to find one that isn't beat to crap.

Hey, Cap'n. My '66 is a short stepper & to find a bed floor that was nice, I had to use one from an '03 Silverado. Was obviously from a construction type longbed truck w/200K on it, but floor was still nice--go figure. It worked VERY nicely. Worst part was the holes I had to drill & then file square w/a 3-sided file.

Looking back, it may have been a bigger job of fitting had it been a fleetside or a longbed.
HTH,
sam

jonzcustomshop · 12-19-2009, 10:13 AM

looks nice, did the wheel tubs and sides bolt on , or did you have to drill?

62 short step · 12-30-2009, 07:01 PM

Here are a few pics. Enjoy!

joe231 · 12-30-2009, 07:06 PM

NICE!!
thanks for the pics!!

Auctioneerhere · 12-07-2012, 02:13 AM

I am going to do this with mine. Thanks for sharing.

62 short step · 12-07-2012, 08:31 AM

Quote:

Originally Posted by Auctioneerhere

I am going to do this with mine. Thanks for sharing.

No problem.

12-18-2009, 02:56 PM	#1
62 short step Senior Member Join Date: Aug 2005 Location: Greenwell Springs, Louisiana Posts: 2,882	67-72 steel floor in a 60-66 Finally got one, it was a long bed but outlawc and I cut it down to a shortbed. Thanks for your help outlawc!! It fits very good, will have to redrill some holes to bolt it to the bed though. Here are some pics. Attached Images __________________ www.louisianaclassictruckclub.com 1965 c-10 86 chevy c/k 20 Last edited by 62 short step; 12-18-2009 at 02:58 PM.

12-18-2009, 03:26 PM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,031	Re: 67-72 steel floor in a 60-66 I have mine sitting in storage waiting for the swap. Looks good.... Anything of note that might prevent problems during the swap? __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

12-18-2009, 04:20 PM	#3
62 short step Senior Member Join Date: Aug 2005 Location: Greenwell Springs, Louisiana Posts: 2,882	Re: 67-72 steel floor in a 60-66 The front bed panel will have to be modified. Since the wood was 3/4 thick, the flange will have to be cut and moved up then welded. I also had to trim this area (in pic) for the sides to fit right. Other than that it wasnt to bad. Attached Images __________________ www.louisianaclassictruckclub.com 1965 c-10 86 chevy c/k 20

12-18-2009, 04:48 PM	#4
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: 67-72 steel floor in a 60-66 Nice work!!!! __________________ *CHEVY ONLY*

12-18-2009, 05:36 PM	#5
62 short step Senior Member Join Date: Aug 2005 Location: Greenwell Springs, Louisiana Posts: 2,882	Re: 67-72 steel floor in a 60-66 Thanks Joe! I need to get some these from mar-k so I can get it bolted up. GM 58-66 FLEETSIDE INNER WALL REPAIR PANELS Attached Images __________________ www.louisianaclassictruckclub.com 1965 c-10 86 chevy c/k 20

12-18-2009, 06:09 PM	#6
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,031	Re: 67-72 steel floor in a 60-66 I'm raising the floor so the front panel is getting modified regardless; I'll watch out for that rear corner now that I'm informed (Thanks!). I did buy a MarK smooth front panel for the 68 so I might see if it would work as well. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.* Last edited by SCOTI; 12-18-2009 at 06:09 PM.

12-18-2009, 06:39 PM	#8
64shortc10 Registered User Join Date: Jan 2007 Location: Winters, Ca. Posts: 1,069	Re: 67-72 steel floor in a 60-66 Did the 67-72 bed floor bolt right to the 60-66 frame stock locations? Thanks Tony from Norcal

12-18-2009, 11:05 PM	#10
62 short step Senior Member Join Date: Aug 2005 Location: Greenwell Springs, Louisiana Posts: 2,882	Re: 67-72 steel floor in a 60-66 Yeah you should be good! __________________ www.louisianaclassictruckclub.com 1965 c-10 86 chevy c/k 20

12-19-2009, 01:47 AM	#11
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,250	Re: 67-72 steel floor in a 60-66 That looks good......now I just need to find one that isn't beat to crap. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

12-19-2009, 10:12 AM	#13
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: 67-72 steel floor in a 60-66 Looks good man...thanks for share the info !! __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

12-19-2009, 10:13 AM	#16
jonzcustomshop 1961 crewcab Join Date: Dec 2007 Location: missoula, mt Posts: 6,164	Re: 67-72 steel floor in a 60-66 looks nice, did the wheel tubs and sides bolt on , or did you have to drill? __________________ 60 build: http://67-72chevytrucks.com/vboard/s...d.php?t=280904 61 crew build: http://67-72chevytrucks.com/vboard/s...d.php?t=646830 63 build: http://67-72chevytrucks.com/vboard/s...d.php?t=336537 64 'burb build: http://67-72chevytrucks.com/vboard/s...d.php?t=448681 65 'burb build: http://67-72chevytrucks.com/vboard/s...d.php?t=590715 65 build: http://67-72chevytrucks.com/vboard/s...d.php?t=281955

12-30-2009, 07:01 PM	#17
62 short step Senior Member Join Date: Aug 2005 Location: Greenwell Springs, Louisiana Posts: 2,882	Re: 67-72 steel floor in a 60-66 Here are a few pics. Enjoy! __________________ www.louisianaclassictruckclub.com 1965 c-10 86 chevy c/k 20

12-30-2009, 07:06 PM	#18
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: 67-72 steel floor in a 60-66 NICE!! thanks for the pics!! __________________ *CHEVY ONLY*

12-07-2012, 02:13 AM	#19
Auctioneerhere Registered User Join Date: Nov 2012 Location: Miles City MT Posts: 241	Re: 67-72 steel floor in a 60-66 I am going to do this with mine. Thanks for sharing.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.