Round Cup holders for factory console - The 1947 - Present Chevrolet & GMC Truck Message Board Network

SCOOBYDOOBYDOO · 03-22-2010, 02:59 PM

I have been seeing a lot of factory consoles with round cup holder does anyone know where to get these ??

John H. · 03-22-2010, 03:19 PM

Not 100% positive, but they were used from 75 up to early 80's? Watch the board in the foresale section

bouncytruck · 03-22-2010, 03:27 PM

Round cup holders are second generation. You can post a wanted to buy on the board or possibly find them in junk yards. LMC may sell repops.

SCOOBYDOOBYDOO · 03-22-2010, 04:11 PM

Ok the consoles I have seen were 69-72 consoles with the seam down the middle

wildwood · 03-22-2010, 04:26 PM

Not completely sure about "seam down the middle", but I had a 79 Blazer that had the cup holders in the console. Looked the same as my 71 otherwise.

bouncytruck · 03-22-2010, 05:08 PM

The consoles are the same with the exception of the cup holders vs. seat belt holders. The consoles can be split in half horizontally, but the upper part is usually where most of the damage and wear is. I believe a few guys have cut the cup holder part out of a new console and put it in place of the seat belt holder part.

BLUE THUNDER · 03-22-2010, 07:59 PM

I bought a console from junkyard and it was out of a second gen. I think it was a '75 and it was exactly the same as my '72 with the exception of the cupholders. It bolted right in. Mario.

SCOOBYDOOBYDOO · 03-22-2010, 08:12 PM

sweet thanks

roachface42 · 03-23-2010, 10:48 AM

I just bought the reproduction console from classic industries for 129.00. It is from the 73-75 body but fits perfect in my 72. Looks sweet... Hope this helps

03-22-2010, 02:59 PM	#1
SCOOBYDOOBYDOO Registered User Join Date: Feb 2010 Location: DANA POINT CA Posts: 256	Round Cup holders for factory console I have been seeing a lot of factory consoles with round cup holder does anyone know where to get these ?? __________________ ScoobyDoobyDoo

03-22-2010, 03:19 PM	#2
John H. Registered User Join Date: Oct 2007 Location: Sammamish, WA Posts: 2,115	Re: Round Cup holders for factory console Not 100% positive, but they were used from 75 up to early 80's? Watch the board in the foresale section

03-22-2010, 03:27 PM	#3
bouncytruck SKINNY TIRES RULE! Join Date: Sep 2001 Location: Bothell, WA Posts: 11,038	Re: Round Cup holders for factory console Round cup holders are second generation. You can post a wanted to buy on the board or possibly find them in junk yards. LMC may sell repops. __________________ bouncytruck 1972 K5 The Hauler 1994 K1500 Suburban The Daily2010 Kia Soul Wife's Ride2014 Fiat 500L

03-22-2010, 04:11 PM	#4
SCOOBYDOOBYDOO Registered User Join Date: Feb 2010 Location: DANA POINT CA Posts: 256	Re: Round Cup holders for factory console Ok the consoles I have seen were 69-72 consoles with the seam down the middle __________________ ScoobyDoobyDoo

03-22-2010, 04:26 PM	#5
wildwood Registered User Join Date: Jun 2003 Location: Calgary AB Posts: 110	Re: Round Cup holders for factory console Not completely sure about "seam down the middle", but I had a 79 Blazer that had the cup holders in the console. Looked the same as my 71 otherwise. __________________ You can't get out if ya don't get in

03-22-2010, 05:08 PM	#6
bouncytruck SKINNY TIRES RULE! Join Date: Sep 2001 Location: Bothell, WA Posts: 11,038	Re: Round Cup holders for factory console The consoles are the same with the exception of the cup holders vs. seat belt holders. The consoles can be split in half horizontally, but the upper part is usually where most of the damage and wear is. I believe a few guys have cut the cup holder part out of a new console and put it in place of the seat belt holder part. __________________ bouncytruck 1972 K5 The Hauler 1994 K1500 Suburban The Daily2010 Kia Soul Wife's Ride2014 Fiat 500L

03-22-2010, 07:59 PM	#7
BLUE THUNDER Registered User Join Date: May 2007 Location: San Antonio Posts: 993	Re: Round Cup holders for factory console I bought a console from junkyard and it was out of a second gen. I think it was a '75 and it was exactly the same as my '72 with the exception of the cupholders. It bolted right in. Mario.

03-22-2010, 08:12 PM	#8
SCOOBYDOOBYDOO Registered User Join Date: Feb 2010 Location: DANA POINT CA Posts: 256	Re: Round Cup holders for factory console sweet thanks __________________ ScoobyDoobyDoo

03-23-2010, 10:48 AM	#9
roachface42 Registered User Join Date: Jan 2010 Location: CA Posts: 78	Re: Round Cup holders for factory console I just bought the reproduction console from classic industries for 129.00. It is from the 73-75 body but fits perfect in my 72. Looks sweet... Hope this helps



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.