![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Mar 2008
Location: Tullahoma, TN
Posts: 406
|
best procedure for door install
I'm fixin to put my doors back on. Never done it before.
My plan: Bolt hinges to door, setting them at the middle of the slots. Set door in cab (put a paint paddle under the bottom to hold it up off the rocker?) Hold it and get the gaps looking like I like, and then tighten the hinges up on the cab. I can see a million things going wrong with this process ![]() I don't know... what's the best procedure for putting a door on and getting it aligned? |
![]() |
![]() |
![]() |
#2 |
Active Member
![]() Join Date: Jul 2007
Location: Centrally located between Houston, Austin and Waco. BCS area.
Posts: 7,947
|
Re: best procedure for door install
My experience on doing this is limited but the few times I've done it I shimmed like you're planning on doing and the rest was strictly trial and error. Mostly move top or bottom one at a time until you get it the way you want it.
Might help if you can get a buddy to help you. |
![]() |
![]() |
![]() |
#3 |
Gone to greener pastures
![]() Join Date: May 2007
Location: Gateway to the Delta
Posts: 7,354
|
Re: best procedure for door install
Take the striker off the door jamb before you start so you don't accidentally get the door jammed tight & unable to open.
Replace the striker after you get the door adjusted to where you want it.
__________________
'69 Chevy 1/2 T LWB Stepper: Daily Beater '72 GMC 3/4 T Fleet: Another Daily Beater '72 Plymouth Gran Coupe: ? "Ah women. They make the highs higher and the lows more frequent." Friedrich Nietzsche "Never kick a fresh turd on a hot day." Harry S. Truman GUN CONTROL: Never having to say, "I missed you." Always fire two warning shots into your attacker's chest area before putting a bullet between his eyes. Paraphrased from Louis Awerbuck |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: best procedure for door install
i use engine hoist to hold door while i boltup hinges
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jun 2005
Location: Scottsdale, AZ
Posts: 615
|
Re: best procedure for door install
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Dec 2008
Location: Gastonia,NC
Posts: 137
|
Re: best procedure for door install
If they are painted, make sure you tape up the edges to help avoid dinging them up!
__________________
Tim |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Apr 2000
Location: Bonne Terre, Mo
Posts: 3,005
|
Re: best procedure for door install
I used a 14" 4 X 4 on a floor jack balanced it the best I could started those bolts in the door. These are doors are heavy even with a helper. Pay attn. to the fine threaded bolts in the hinges..They are easy to cross thread.
__________________
'69 Chevy Long Fleet & '71 GMC Short Step & Project "ODD BALL" "You can wash a pig, soak it in most expensive perfume. In the end it is still just a pig." ODD BALL build thread http://67-72chevytrucks.com/vboard/s...d.php?t=478629" |
![]() |
![]() |
![]() |
#8 |
Registered User
![]() Join Date: May 2007
Location: Rapid City South Dakota
Posts: 2,359
|
Re: best procedure for door install
I bolt the hinges to the post, then set the door on my knee and bolt it to the hinge. When empty, these doors are light as far as doors go. These trucks are about the easiest thing there is to hang a door onto. Don't make it harder than it needs to be. Make sure you clean the threads with a tap and die first. This alone will make things much easier.
__________________
Turp Mcspray New life for an old 2wd, farm blazer http://67-72chevytrucks.com/vboard/s...d.php?t=505987 My Blazer build http://67-72chevytrucks.com/vboard/s...d.php?t=342299 |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Dec 2009
Location: California, Maryland
Posts: 544
|
Re: best procedure for door install
1. Get it hung and to the point where it swings without binding.
2. Adjust up/down so the body crease lines matches in the up/down direction by adjusting the bolts on the body pillar. Also adjust for front/back clearance at this time. 3. Put the latch plate back in and adjust latch plate bolts so the the door is level to the body right at the latch plate. You may have to add/delete latch plate spacers. Use a straightedge to check for alignment. If don't have weatherstrip, pull out on the door when you measure. 4. You can then move the top and bottom hinges in and out until the door is parallel to the body. You do this by adjusting the bolts on the door. Also check alignment at the front roof pillar where it meets the door body at this time.
__________________
72 Fleet (died) 78 Step (sold) 55 Step named Fred (sold) 00 F150 68 Step (named El Scorcho by PO) Build thread for the new El Scorcho http://67-72chevytrucks.com/vboard/s...d.php?t=392932 |
![]() |
![]() |
![]() |
Bookmarks |
|
|