The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1988 - 1998 GMT400 Chevy & GMC Pickups Message Board > projects and builds 88-98

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 05-26-2010, 01:48 PM   #1
IndyAnne
Registered User
 
IndyAnne's Avatar
 
Join Date: Dec 2009
Location: indianapolis, IN
Posts: 81
Schematics on AC shroud removal?

I am stuck. I am trying to remove the upper section of the AC condenser shroud in my 88 K1500 extended cab with factory AC.

I have managed to remove some 7mm screws attaching the top piece to the middle piece. I have the bottom section off for replacement of the heater core (successful). I also got one 10mm screw out that bolts through the firewall. I see some other screw "tails" coming through the firewall in the vicinity of the condenser.

I have the Haynes and Chilton manuals that are general repair and maintenance info, but nothing specific about the AC. I understand it is dangerous to mess with the AC, but I don't want to remove any of the lines, just want to get to the condenser to clean it up.

I have the dash out, including all of the vents, so I can get to as much as possible.

Any advice with photos would be welcome. Thanks!

I will post photos next.
__________________
IndyAnne
Indianapolis, Southside
Project photos with comments: http://www.flickr.com/photos/indyanne1/
1988 Chevy K1500 Silverado, 2-door extended cab, long bed, 350 5.7 gas, automatic transmission, built in Canada
http://web.me.com/agm57/IndyAnnes_Bi...vy/Photos.html
Tow vehicle for 1968 Airstream Trade Wind
http://web.me.com/agm57/IndyAnnes_Ai...os/Photos.html
IndyAnne is offline   Reply With Quote
Old 05-26-2010, 02:17 PM   #2
IndyAnne
Registered User
 
IndyAnne's Avatar
 
Join Date: Dec 2009
Location: indianapolis, IN
Posts: 81
Re: Schematics on AC shroud removal?

Sorry, I am trying to present the photos in line with comments, but it's not working. Please click on the title of each photo at the tops of the photo windows to, I hope, go to the image stored on Flickr.com

Or, see the entire set with descriptions here:
http://www.flickr.com/photos/indyann...7624142079892/

Photos now:

I want to remove this upper section of the AC condenser shroud, to clean the condenser; the section with the arched top covers the condenser. This condenser is very dirty, coated with grime, and there are leaves and crud packed in. I can feel that the AC lines in the engine compartment are very cold, maybe not cold enough, but this condenser cleaning will help tremendously, if I could get to it!

This photo shows that the shroud does come apart, clamshell style, that should leave a middle section to hold the heater core in place:

This is the left end of the shroud showing the clamshell fit around a semi-circular section of the central vent assembly:

underneath, looking up at the heater core segment of the shroud:

right end, showing the fan motor shroud, minus the fan and motor:

Locations of a couple of several 7mm screws holding the shroud sections together:

Top top of the condenser shroud, and the location (empty hole) where a 10mm screw bolts through the firewall:

The engine compartment, showing the nut attached to the firewall, I removed the top one, that appears on the left of the photo, but there is a second screw below that is not accessible from inside the cab:

The AC accumulator and the inlet/outlet lines; heater core line into the engine block has a bend/kink in the line:

Quote:
Originally Posted by IndyAnne View Post
I am stuck. I am trying to remove the upper section of the AC condenser shroud in my 88 K1500 extended cab with factory AC.

I have managed to remove some 7mm screws attaching the top piece to the middle piece. I have the bottom section off for replacement of the heater core (successful). I also got one 10mm screw out that bolts through the firewall. I see some other screw "tails" coming through the firewall in the vicinity of the condenser.

I have the Haynes and Chilton manuals that are general repair and maintenance info, but nothing specific about the AC. I understand it is dangerous to mess with the AC, but I don't want to remove any of the lines, just want to get to the condenser to clean it up.

I have the dash out, including all of the vents, so I can get to as much as possible.

Any advice with photos would be welcome. Thanks!

I will post photos next.
__________________
IndyAnne
Indianapolis, Southside
Project photos with comments: http://www.flickr.com/photos/indyanne1/
1988 Chevy K1500 Silverado, 2-door extended cab, long bed, 350 5.7 gas, automatic transmission, built in Canada
http://web.me.com/agm57/IndyAnnes_Bi...vy/Photos.html
Tow vehicle for 1968 Airstream Trade Wind
http://web.me.com/agm57/IndyAnnes_Ai...os/Photos.html

Last edited by IndyAnne; 05-26-2010 at 02:49 PM.
IndyAnne is offline   Reply With Quote
Old 05-26-2010, 03:00 PM   #3
TennesseeZ
Countdown Survivor
 
TennesseeZ's Avatar
 
Join Date: Aug 2007
Location: Bean Station, East Tennessee
Posts: 9,676
Re: Schematics on AC shroud removal?

Off subject but here's some info on creating albums and uploading photos here.

And you can upload directly from your hard drive to a thread by clicking "go advanced" at the bottom of the post window, scroll down to Additional Options, Attach Files, Manage Attachments, and then upload them.

Then you can give a running commentary with each pic, and the pics are stored and never leave the post.
__________________
93 Yukon
89 Silverado Z71 SWB Sport
91 K 2500 Silverado "Lobuk-Worktruk"

A MAN OF HONOR DOES NOT LIE, CHEAT, OR STEAL, NOR TOLERATE THOSE WHO DO.

Gettin' old ain't for sissies.

Last edited by TennesseeZ; 05-26-2010 at 10:41 PM.
TennesseeZ is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:14 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com