Not so new project 1970 K10

[Travis K]

I have been hanging around this site for a little over 3 years now, and have learned a lot from everyone. I have decided to finally start my own build thread. I actually started my build a few years ago, but progress was slow at best. Between getting married, going to military schools (I am active duty in the North Dakota National Guard), and being deployed, I haven't been able to make much progress. I get back from my current deployment soon, and I plan on really getting started on this project when I get home.

I have always wanted to do a frame off on a 67-72 Chevy truck. I had a '69 K10 that I started back in high school, but the parents didn't really care for the space it took in the garage. I had them sell it for me the summer that I went to basic training. Years later, I had a few extra bucks (and my own garage), so I decided it was time to get started. I couldn’t find a K10 in my area that was in decent shape, so I purchased a 1970 LWB C10. The body was in good shape, with minor rust in the floorpan, rockers, and cab corners. Then, through a friend, I found a cheap ’68 K10. The body on the K10 was in pretty rough shape, but the chassis was straight and in good condition. Here are some pictures of what I had to start out with:

[Travis K]

a few more:

[Travis K]

a couple of the '68. It came complete, but I didn't take any pictures of it that way.

and the '68 down to bare frame:

[Travis K]

My plan is to use the 4x4 chassis with the '70 body. The body did need some rust repair, and I had never welded before. I took an evening welding class at the local Votech Center, and read a lot of threads on this website before I jumped in. The first cut into the body of your truck can be nerve wracking, especially when you don't have experience welding. The members on this site were very inspirational and motivating, so I jumped right in. I started with replacing the driver's side floorpan, rockers, and cab corner. This build my confidence, so I decided to try smoothing my firewall next. Here are some pics of the firewall after the mod:

[Travis K]

After this mod, and a bunch of other welding projects around the garage, I decided to start on my custom dash. I cut the mid-section out of the dash, so I could work on it at the bench. I am using a Vintage Air control panel for their Gen IV system, I don't remember off hand where the vents came from, and I will be putting a double DIN DVD receiver in the dash. Here are some pictures of the progress on it.

[Travis K]

and more:

[Dieselwrencher]

Kick azz project!

[72BlckButy]

Is that a repop bed?

[Rodk65]

Great looking project. The 5.3 swap is something I want to do in my 4x4. Keep up the good work.

[Travis K]

Thanks for the compliments guys. It is definitely a learning experience. Being deployed for a year gives you a lot of time to plan your project, so hopefully progress will go fast. My goal is to have it finished by early summer. I am trying to get as much done while it is nice out though. Winter is coming fast. It actually snowed here after work last Friday!

Black Beauty, only the sides are repop. Unfortunately, they came with some pretty large dents in them. I will work on those after I weld in the fuel filler door. I actually stole the floor out of my wife's '71 because it was straighter than mine. I am not sure I will ever live that one down. I promised to get hers back together once there is room in the garage.

[silver7]

Looks good. I'm envious of how quick your getting things done. Keep it up and you'll be finished in no time.

[Travis K]

Haven't had a chance to work on the truck in almost a month, kind of frustrating. Winter is going to be here soon, and I have been helping my brother get his new yard together. The bad thing is that you only get about an hour or two to work outside since the sun goes down so early this time of year. That means projects that should take a night or two, take a week or so. I did have a couple hours to work on the truck today. I got the fuel filler door fitted into the bedside, powered up the welder, threw in a tack weld, and it looked like chicken poop. My tank was empty, figures. I must have a leak somewhere, because I haven't done that much welding since I have been home. Unfortunately, I probably won't get a chance to work on it for a few more weeks.

[swamp rat]

Originally Posted by Travis K

Haven't had a chance to work on the truck in almost a month, kind of frustrating. Winter is going to be here soon, and I have been helping my brother get his new yard together. The bad thing is that you only get about an hour or two to work outside since the sun goes down so early this time of year. That means projects that should take a night or two, take a week or so. I did have a couple hours to work on the truck today. I got the fuel filler door fitted into the bedside, powered up the welder, threw in a tack weld, and it looked like chicken poop. My tank was empty, figures. I must have a leak somewhere, because I haven't done that much welding since I have been home. Unfortunately, I probably won't get a chance to work on it for a few more weeks.

Hey at least you have a nice garage to work in! Your doing a flip door for the gas fill? Thats my plan also, i'd really like to see pic's of the install if you have them?

[silver7]

Really like your plan for the color of the truck with large newer style wheels. I have a similar thought for mine but I don't have photoshop to post it.

[Travis K]

Here are the pix I have of the filler door install. I think I bought it from Hagan Street Rods. If I had to do it again, I think I would cut one off of a salvaged newer Silverado. The filler door is only one thickness of metal on the edges. I am afraid of paint chipping. I don't know much about body work though. If someone can tell me different, please do. If not, I think I am going to add a strip on the back side. I did get some warping above the filler on the bedside. I hate welding on large panels. I even took my time (about 1 1/2 hours) to weld this thing in. I guess I will have to figure out how to fix it after I shave the marker lights. Again, if anyone has any tips on fixing the warpage, let me know. I am teaching myself metal work and body work, so tips from people with experience is always helpful.

On another note, I received my Doug Thorley LS swap headers tonight. I only held them up to the block, but if anyone needs to know, they fit beautifully. Can't wait to bolt them up, and route some exhaust. That will have to wait. I still have a couple weeks of helping my bro in his yard before I get more garage time.

Anyway, here are the pix of the fuel filler install:

Tack Welded:



All welded up:











Used cutoffs from shortening the bed, and my break to fab up an access panel/cover:

[swamp rat]

I cant thank you enough for posting the pic's! I was trying to figure out how to make a backing plate like you did with the bed material in the last pic, i have no excess bed material right now, guess i have to find some..

One question i have is if you flanged the bed cuttout with a flanger tool? or did you just cut the opening the same size as your flip door assy?

I talked to a guy i work with who does body work on the side, he recomended not using squair or rectangle pieces but rather oval shapes when spot welding in a door assy. he said it will help minimise warpage, he also recomended flanging the opening so the piece overlaps the bed, spot weld it in then use seam sealer on the back side..

I am still pretty petrafide of cutting my bed... even tho its just steel.. :p

[Travis K]

I didn't flange it, I prefer butt welds. Besides, it would be tough to reach seam sealer all the way around and make sure it is covering the seam well. I wonder how welding in an oval hole creates less warpage than a square hole? I may try it when I fill the side markers. The way I see it, heat is heat, and that is what warps the panel.

Even if you don't have any bed cutoff for the flange, it wouldn't take much to form a 1" strip to follow the contour. I think it would have taken less time to do that than cutting off the piece and removing all of the paint and undercoating. Plus, it is satisfying to make something like that from scratch.

[swamp rat]

I have absolutly no idea myself about the oval, just passing along what he said.. That does raise the question tho... How would you cut out an oval with any precision??

But i agree about trying to apply seam sealer may be an issue unless ya remove a large enough piece of the inner bed, but i like the way you did yours!