motor pull on a 98 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

dammitmitchell · 07-11-2010, 07:24 PM

hey gents gotta pull and replace the motor on my 98 blazer.

question of the day is
pull motor tranny out as a whole?
pull motor seperate from tranny?

do i need to pull the radiatior support to get this little bugger out?

thanks!

any heads up is appreciated. I feel i need the hands of an oriental woman to work on this thing.

68C15 · 07-12-2010, 06:22 AM

leave the tranny and rad. support.
this is pretty straight forward aside from the 2 upper bolts on the driver's side of bell housing. I have found it easier to remove the steering intermediate shaft and lift body 2 or 3 inches.
another thing that makes it easier is to remove engine wiring harness from under the fuse block and lay it all over the pass. fender.

why the motor pull?

dammitmitchell · 07-12-2010, 04:35 PM

bad motor no compression.

lvschevytrucks · 07-20-2010, 12:48 AM

Check out the build on my 95, Blazer, its not to bad if you lift the body.

**truckdude239** · 07-20-2010, 12:02 PM

well if it is anything like the 2.8 i did in our company blazer (1988) i removed the front 6 mounts used the lif tot lift the body and put a 4x4 block under the 2 mounts at the doors. pulled the tranny then the motor

lvschevytrucks · 07-20-2010, 03:55 PM

Quote:

Originally Posted by truckdude239

well if it is anything like the 2.8 i did in our company blazer (1988) i removed the front 6 mounts used the lif tot lift the body and put a 4x4 block under the 2 mounts at the doors. pulled the tranny then the motor

I did the same thing but without removing the tranny

**truckdude239** · 07-21-2010, 06:52 AM

well we replaced the tranny and motor

Damien · 07-25-2010, 04:24 PM

I have found it easier to pull the trans with the engine on 2 wheel drive trucks atleast. The body can be left alone

07-11-2010, 07:24 PM	#1
dammitmitchell the pollock Join Date: May 2008 Location: abilene, texas Posts: 4,423	motor pull on a 98 hey gents gotta pull and replace the motor on my 98 blazer. question of the day is pull motor tranny out as a whole? pull motor seperate from tranny? do i need to pull the radiatior support to get this little bugger out? thanks! any heads up is appreciated. I feel i need the hands of an oriental woman to work on this thing. __________________ Jack of ALL trades, Master of none.. (but one... procrastination) Army vet 02-08 RIP El Jay! Miss you brother! http://67-72chevytrucks.com/vboard/s...d.php?t=343538 http://67-72chevytrucks.com/vboard/s...d.php?t=386042

07-12-2010, 06:22 AM	#2
68C15 blood type; Retumbo Join Date: Jan 2004 Location: next to my reloading bench Posts: 10,269	Re: motor pull on a 98 leave the tranny and rad. support. this is pretty straight forward aside from the 2 upper bolts on the driver's side of bell housing. I have found it easier to remove the steering intermediate shaft and lift body 2 or 3 inches. another thing that makes it easier is to remove engine wiring harness from under the fuse block and lay it all over the pass. fender. why the motor pull?

07-12-2010, 04:35 PM	#3
dammitmitchell the pollock Join Date: May 2008 Location: abilene, texas Posts: 4,423	Re: motor pull on a 98 bad motor no compression. __________________ Jack of ALL trades, Master of none.. (but one... procrastination) Army vet 02-08 RIP El Jay! Miss you brother! http://67-72chevytrucks.com/vboard/s...d.php?t=343538 http://67-72chevytrucks.com/vboard/s...d.php?t=386042

07-20-2010, 12:48 AM	#4
lvschevytrucks Unfinished Project Club Join Date: Jul 2005 Location: Florence S.C. Posts: 596	Re: motor pull on a 98 Check out the build on my 95, Blazer, its not to bad if you lift the body. __________________ Handle every Stressful situation like a dog. If you can't eat it or play with it, Pee on it and walk away. 1996 Dodge Intreped ES Nice car great on gas 1993 Jeep Cherokee. Looking for a swb chevy 73-87

07-20-2010, 12:02 PM	#5
truckdude239 Senior Member Join Date: Sep 2005 Location: Lewisville, Nc Posts: 10,237	Re: motor pull on a 98 well if it is anything like the 2.8 i did in our company blazer (1988) i removed the front 6 mounts used the lif tot lift the body and put a 4x4 block under the 2 mounts at the doors. pulled the tranny then the motor __________________ David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube

07-21-2010, 06:52 AM	#7
truckdude239 Senior Member Join Date: Sep 2005 Location: Lewisville, Nc Posts: 10,237	Re: motor pull on a 98 well we replaced the tranny and motor __________________ David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube

07-25-2010, 04:24 PM	#8
Damien Registered User Join Date: Mar 2007 Location: Farmington, MN Posts: 928	Re: motor pull on a 98 I have found it easier to pull the trans with the engine on 2 wheel drive trucks atleast. The body can be left alone __________________ I can still count my vehicles on two... wait three hands.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.