VIN # Issue - The 1947 - Present Chevrolet & GMC Truck Message Board Network

wtatters · 07-21-2010, 04:56 PM

Hello everyone, Ive been reading alot on the forums the last couple weeks and looking at the great pictures of all your trucks. I found a truck Id like to buy and I have been out to look it over. My problem is that I wrote down the VIN # off the drivers side door jam and Im having a hard time decoding it with the information I have found. The VIN was GM2590DZC2045B it is supposed to be a 1967 2wd swb chevrolet. Any help would be great. It also has the factory A/C on the bottom of the dash and power brakes.

RustWrangler · 07-21-2010, 05:04 PM

Scratch that, I posted a VIN decoder for you but your VIN does not match up. Not sure what you have there hopefully one of the other guys will.

Longhorn Man · 07-21-2010, 05:43 PM

can you get a photo of he VIN plate?
You sure it isn't a GMC?

**burb71** · 07-21-2010, 05:54 PM

FYI, the factory only installed in dash air, under dash is dealer installed or a aftermarket company.

bruceman1968 · 07-22-2010, 02:29 AM

Hello Wtatters and WELCOME to the board. I think you got a gmc vin there.
G= van/jimmy
m=v6
2=3/4 ton
59- cab to rear axel dimension (actualy 54 inches)
OD= wide side box
Z= fremont assy. plant
C= year 1967
2045=sequence number
B=GVW range 6001# to 10000#
If that first digit is a C instead of G then it's conv. cab 2wd.

wtatters · 07-22-2010, 08:25 AM

Thanks for the help everyone. Im going today to look at it again and Ill try to double check that VIN. here it is http://springfield.craigslist.org/cto/1849345671.html if anyone was interested.

gkesseru · 07-22-2010, 08:46 AM

Compare that $10K to what you can get at a used car lot. I would have guessed it to be more expensive.

**BIG ORANGE** · 07-22-2010, 08:55 AM

Doesnt look bad, small backglass wasnt rare,most all early 67 were small rear windows. Looks like it's missing carpet or matt in the floor, I would do some jewing down on him if your comfortable doing so!
Oyea welcome to the truck forum, hope you enjoy it, we do...........
Donnie

vectorit · 07-22-2010, 09:48 AM

Nice looking truck!
But the seller lost me, when I read "short wide"...
Or maybe I just need to finish my coffee.

**LockDoc** · 07-22-2010, 10:04 AM

-
If the seller has the paperwork to back up the "Newly rebuilt motor and tranny" statement there is no way you could duplicate that truck for 10 grand, even doing most of the work yourself.

LockDoc

wtatters · 07-22-2010, 12:33 PM

So does the 54" cab to axle dimension in VIN signify that it is truly a short bed pickup?

bruceman1968 · 07-22-2010, 01:43 PM

I'm not sure yet I'm checking I was thinking 42 was short and 54 is long but I'm still checking to be sure. Also I found a gmc chassis code that was G=light duty..... but I'm not sure what year so no worries if the first digit is in fact a G

07-21-2010, 04:56 PM	#1
wtatters Registered User Join Date: Jul 2010 Location: springfield missouri Posts: 3	VIN # Issue Hello everyone, Ive been reading alot on the forums the last couple weeks and looking at the great pictures of all your trucks. I found a truck Id like to buy and I have been out to look it over. My problem is that I wrote down the VIN # off the drivers side door jam and Im having a hard time decoding it with the information I have found. The VIN was GM2590DZC2045B it is supposed to be a 1967 2wd swb chevrolet. Any help would be great. It also has the factory A/C on the bottom of the dash and power brakes.

07-21-2010, 05:04 PM	#2
RustWrangler Registered User Join Date: Jun 2009 Location: Douglasville, GA Posts: 7	Re: VIN # Issue Scratch that, I posted a VIN decoder for you but your VIN does not match up. Not sure what you have there hopefully one of the other guys will. __________________ 1967 Stepper built and about to be rebuilt in Atlanta, GA Last edited by RustWrangler; 07-21-2010 at 05:14 PM.

07-21-2010, 05:43 PM	#3
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	Re: VIN # Issue can you get a photo of he VIN plate? You sure it isn't a GMC?

07-21-2010, 05:54 PM	#4
burb71 Active Member Join Date: Oct 2002 Location: Ft. Myers, Fl Posts: 1,716	Re: VIN # Issue FYI, the factory only installed in dash air, under dash is dealer installed or a aftermarket company.

07-22-2010, 02:29 AM	#5
bruceman1968 Registered User Join Date: Oct 2009 Location: Tampa Bay Posts: 1,549	Re: VIN # Issue Hello Wtatters and WELCOME to the board. I think you got a gmc vin there. G= van/jimmy m=v6 2=3/4 ton 59- cab to rear axel dimension (actualy 54 inches) OD= wide side box Z= fremont assy. plant C= year 1967 2045=sequence number B=GVW range 6001# to 10000# If that first digit is a C instead of G then it's conv. cab 2wd. __________________ CHEVY/GMC VIN DECODERS Last edited by bruceman1968; 07-22-2010 at 05:36 AM.

07-22-2010, 08:25 AM	#6
wtatters Registered User Join Date: Jul 2010 Location: springfield missouri Posts: 3	Re: VIN # Issue Thanks for the help everyone. Im going today to look at it again and Ill try to double check that VIN. here it is http://springfield.craigslist.org/cto/1849345671.html if anyone was interested.

07-22-2010, 08:46 AM	#7
gkesseru Registered User Join Date: Dec 2009 Location: California, Maryland Posts: 544	Re: VIN # Issue Compare that $10K to what you can get at a used car lot. I would have guessed it to be more expensive. __________________ 72 Fleet (died) 78 Step (sold) 55 Step named Fred (sold) 00 F150 68 Step (named El Scorcho by PO) Build thread for the new El Scorcho http://67-72chevytrucks.com/vboard/s...d.php?t=392932

07-22-2010, 08:55 AM	#8
BIG ORANGE Senior Member Join Date: Oct 2001 Location: Lancaster S.C. Posts: 4,754	Re: VIN # Issue Doesnt look bad, small backglass wasnt rare,most all early 67 were small rear windows. Looks like it's missing carpet or matt in the floor, I would do some jewing down on him if your comfortable doing so! Oyea welcome to the truck forum, hope you enjoy it, we do........... Donnie __________________ Things happen for a reason!

07-22-2010, 09:48 AM	#9
vectorit What? Join Date: Jun 2007 Location: Southern California Posts: 7,617	Re: VIN # Issue Nice looking truck! But the seller lost me, when I read "short wide"... Or maybe I just need to finish my coffee. __________________ Chris 1968 K20 Suburban 1972 K10 LWB PU

07-22-2010, 10:04 AM	#10
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,639	Re: VIN # Issue - If the seller has the paperwork to back up the "Newly rebuilt motor and tranny" statement there is no way you could duplicate that truck for 10 grand, even doing most of the work yourself. LockDoc __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

07-22-2010, 12:33 PM	#11
wtatters Registered User Join Date: Jul 2010 Location: springfield missouri Posts: 3	Re: VIN # Issue So does the 54" cab to axle dimension in VIN signify that it is truly a short bed pickup?

07-22-2010, 01:43 PM	#12
bruceman1968 Registered User Join Date: Oct 2009 Location: Tampa Bay Posts: 1,549	Re: VIN # Issue I'm not sure yet I'm checking I was thinking 42 was short and 54 is long but I'm still checking to be sure. Also I found a gmc chassis code that was G=light duty..... but I'm not sure what year so no worries if the first digit is in fact a G __________________ CHEVY/GMC VIN DECODERS



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.