235 Engine Removal Question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Apollo 62C20 · 08-09-2010, 11:01 PM

Is it possible to pull out a straight 6 (235) without pulling the bell housing and tranny? My truck is a 1962 C20 if that makes a difference... The parking brake is the kind with the (leather?) strap around the drum.

It looks like I am going to have to unbolt the tranny and pull the block and bell housing together. Is there a better way?

Thanks--This is surely in the manual but I haven't gotten it yet and I have searched the forums for a while and haven't found any conclusive threads...

**Captainfab** · 08-10-2010, 12:54 AM

Yes you can pull just the engine if that's what you want to do. Personally I find it easier for reinstallation to have the bellhousing, flywheel and clutch installed onto the engine. For me it's easier to install the trans onto the bellhousing, than to try and get the engine lined up with the trans , bellhousing and clutch all at the same time.

Apollo 62C20 · 08-10-2010, 08:07 AM

Thanks for the quick response CAPTAINFAB. Engine and Bell it is! Dad and I are gonna pull it today... I'll post some feedback and some pics if I can.

Malibob · 08-10-2010, 12:53 PM

Send it to me when you get it out. I love the 235 and straight 6'ers.

Apollo 62C20 · 08-10-2010, 04:49 PM

UPDATE:

Following Captainfab (and my pops) advice we pulled the 4 bolts attaching the bell housing to the tranny. I believe the bolts were 3/4". Two are on top of the tranny and two are inside the bell. Once those were out we just raised the engine hoist until the front mount cleared the cross member and pulled forward to separate the bell from the tranny. I put a jack on the clutch assembly to help keep it off the rear cross member and level the motor as we slid it out of the tunnel. From then on it was pretty much a straight shot into the garage.... hope that helps...

Unfortunately I discovered that the Exhaust manifold was fatally cracked and then the radiator guy called me back to tell me mine was not repairable unless I had $400...
Otherwise motor looks pretty good...pics soon.

Malibob - I'm fond of this motor too and am only pulling it to do a gasket/freeze plug/seal update and replace the throw out (release) bearing.

Anyone got an exhaust manifold for sale?

raycow · 08-10-2010, 06:58 PM

In case you do need to pull the bellhousing for some reason, the flywheel has to come off first. 4 of the bellhousing bolts are behind the flywheel.

Ray

Malibob · 08-11-2010, 07:02 AM

Glad to hear you are keeping the 6. Too many of them are being scrapped in my opinion. They were good motors.

Apollo 62C20 · 08-11-2010, 09:22 AM

Thanks Ray...I did a bit of head scratching before I got the bell off. Looks like the throw out bearing is definitely shot. Clutch looks good.

Mali- This motor runs strong and smooth, at least it did before I pulled it out. Dad is waiting for the day I decide to put a 350 in it....it may be a while!

08-09-2010, 11:01 PM	#1
Apollo 62C20 Registered User Join Date: Aug 2010 Location: Tallahassee, Fl Posts: 20	235 Engine Removal Question Is it possible to pull out a straight 6 (235) without pulling the bell housing and tranny? My truck is a 1962 C20 if that makes a difference... The parking brake is the kind with the (leather?) strap around the drum. It looks like I am going to have to unbolt the tranny and pull the block and bell housing together. Is there a better way? Thanks--This is surely in the manual but I haven't gotten it yet and I have searched the forums for a while and haven't found any conclusive threads...

08-10-2010, 12:54 AM	#2
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: 235 Engine Removal Question Yes you can pull just the engine if that's what you want to do. Personally I find it easier for reinstallation to have the bellhousing, flywheel and clutch installed onto the engine. For me it's easier to install the trans onto the bellhousing, than to try and get the engine lined up with the trans , bellhousing and clutch all at the same time. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

08-10-2010, 08:07 AM	#3
Apollo 62C20 Registered User Join Date: Aug 2010 Location: Tallahassee, Fl Posts: 20	Re: 235 Engine Removal Question Thanks for the quick response CAPTAINFAB. Engine and Bell it is! Dad and I are gonna pull it today... I'll post some feedback and some pics if I can.

08-10-2010, 12:53 PM	#4
Malibob Registered User Join Date: May 2009 Location: Pittsburgh Posts: 392	Re: 235 Engine Removal Question Send it to me when you get it out. I love the 235 and straight 6'ers. __________________ This statement was made possible by a grant from this station and continued support from viewers like you. Flickr Last edited by Malibob; 08-10-2010 at 12:53 PM. Reason: y in you

08-10-2010, 04:49 PM	#5
Apollo 62C20 Registered User Join Date: Aug 2010 Location: Tallahassee, Fl Posts: 20	Re: 235 Engine Removal Question UPDATE: Following Captainfab (and my pops) advice we pulled the 4 bolts attaching the bell housing to the tranny. I believe the bolts were 3/4". Two are on top of the tranny and two are inside the bell. Once those were out we just raised the engine hoist until the front mount cleared the cross member and pulled forward to separate the bell from the tranny. I put a jack on the clutch assembly to help keep it off the rear cross member and level the motor as we slid it out of the tunnel. From then on it was pretty much a straight shot into the garage.... hope that helps... Unfortunately I discovered that the Exhaust manifold was fatally cracked and then the radiator guy called me back to tell me mine was not repairable unless I had $400... Otherwise motor looks pretty good...pics soon. Malibob - I'm fond of this motor too and am only pulling it to do a gasket/freeze plug/seal update and replace the throw out (release) bearing. Anyone got an exhaust manifold for sale?

08-10-2010, 06:58 PM	#6
raycow Registered User Join Date: Mar 2003 Location: San Francisco, CA USA Posts: 2,454	Re: 235 Engine Removal Question In case you do need to pull the bellhousing for some reason, the flywheel has to come off first. 4 of the bellhousing bolts are behind the flywheel. Ray

08-11-2010, 07:02 AM	#7
Malibob Registered User Join Date: May 2009 Location: Pittsburgh Posts: 392	Re: 235 Engine Removal Question Glad to hear you are keeping the 6. Too many of them are being scrapped in my opinion. They were good motors. __________________ This statement was made possible by a grant from this station and continued support from viewers like you. Flickr

08-11-2010, 09:22 AM	#8
Apollo 62C20 Registered User Join Date: Aug 2010 Location: Tallahassee, Fl Posts: 20	Re: 235 Engine Removal Question Thanks Ray...I did a bit of head scratching before I got the bell off. Looks like the throw out bearing is definitely shot. Clutch looks good. Mali- This motor runs strong and smooth, at least it did before I pulled it out. Dad is waiting for the day I decide to put a 350 in it....it may be a while!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.