Question about rims/tires and lowering setup

[ATrain707]

Hey guys first off I'm new here. I bought a 68 c10 long bed for 1000, with a straight six 4speed the body is fairly clean, the floor of the cab has some rust by the the doors which is common I hear. It runs great. My question is I bought a set of rims they are 20x8.5 the lug pattern is the same but I'm gonna have to use 1in adapters to get them to fit cuz the offset isn't right. The tires are 275x45x20 what size tires should I run and how low can I go? I don't want to have problems rubbing. I was thinking 2in in front and 3in in the rear but I would like to do 3in in front and 4in in the rear with air shocks in the rear but not sure what would be best with the size rims I bought, I bought the rims cuz I only got them 300. I'll post pics of the rims and truck later this evening
Posted via Mobile Device

[charx2]

I have bags on my 67 stepper and it really prevents me from getting wide rims. I been thinking about kind of tubbing out the inner fender to get some more room. Right now I have 15's on it and when I drop it to the ground, the RR tire rubs against the inner fender and the LR tire rubs against the out fender! FYI, when you drop these trucks it moves the rear end to the pass side if I remember correctly?

[VDOG]

Originally Posted by charx2

I have bags on my 67 stepper and it really prevents me from getting wide rims. I been thinking about kind of tubbing out the inner fender to get some more room. Right now I have 15's on it and when I drop it to the ground, the RR tire rubs against the inner fender and the LR tire rubs against the out fender! FYI, when you drop these trucks it moves the rear end to the pass side if I remember correctly?

I had the same problem when I lowered mine. I used ratchting straps, hook one in the top opening of the middle stake pocket, then took it down and under the truck to the other side of the rearend and hooked it up.
The only thing, you need to have the adjustable panhard bar.
The object is to center the bed over the rearend, that way your tires will be centerd under the wheel wells. I have 15x10.5 on the back. Once I did the above step I had no issues with rubbing.

[ATrain707]

i installed some aftermarket gauges in the cluster, of my brothers 71 and also installed some black housing projector headlights with 8000k HID headlights, ill take some pics and post them up

[ATrain707]

theres the pics of the gauges the are led and you can switch them 7 different colors.

[ATrain707]

can anyone tell me how to adjust a colum shifter? its way too sloppy

[ATrain707]

Is it hard to tub the inner fender? I would probably have to do it to the front and rear but not really sure til I get my wheel spacers in then I can go from there
Posted via Mobile Device

[ATrain707]

ok heres pics of my truck i got and the rims i bought for it is it hard to roll or flare the fender to make a bit more room for the tires? im goona put smaller tires the ones on the rims are 275x45 but im not sure what too run

[ATrain707]

well i started working on my truck again. i bought new lowering shocks up front and air shocks in the rear, also installed the new lowering coils 3in in front and 4in in the rear and put the rims on, the rims i bought were from a 2000 trail blazer they are 20x8.5 i had to buy 1.5 adapters for the rear and 1.0 adapters for the front. i still think the front needs to be lower. drop spindles? and from where? and how much of a drop?

[wwotr]

Originally Posted by ATrain707

well i started working on my truck again. i bought new lowering shocks up front and air shocks in the rear, also installed the new lowering coils 3in in front and 4in in the rear and put the rims on, the rims i bought were from a 2000 trail blazer they are 20x8.5 i had to buy 1.5 adapters for the rear and 1.0 adapters for the front. i still think the front needs to be lower. drop spindles? and from where? and how much of a drop?

Welcome to the Forum from Lake County!

Heres some pictures of my 72 GMC Short Fleet.
I'm running 15" Rally Wheels with a 5.5" Drop in Front and 6" in the rear.
Front lowering was accomplished using 2.5" Lowering Spindles and 3" lowering Springs.
Rear was done with 4" Lowering Springs and 2" Drop Blocks.

[steppside69]

Welcome to the site, Are you running drums all the way around? I think the only way you can get drop spindals is to convert the front drums to disks. I know that the FAQ suspension section is PRICELESS with info on this swap!!! Eric

[ATrain707]

so the drop spindles are only made for disk break? yea im running drums all the way around. nice truck.

[brans72]

if you wanna do dics brakes on a budget and know local guys and junkyards you could do a early 80's front end swap subframe and all. Will give you disc brakes and parts are cheaper! Brandon

[w3lfd]

Originally Posted by brans72

if you wanna do dics brakes on a budget and know local guys and junkyards you could do a early 80's front end swap subframe and all. Will give you disc brakes and parts are cheaper! Brandon

Only problem with that plan is that he would be going from 6 lug to 5 lug and need to get different wheels.

http://www.classicparts.com/1963-70-...info/71-977D6/

This is one of the routes you would need to go to keep the 6 lug.

[ATrain707]

do i need to do a c notch if i lower the rear 5 inches, or will i be ok?

[wwotr]

Originally Posted by ATrain707

do i need to do a c notch if i lower the rear 5 inches, or will i be ok?

Atrain707,
See my above post w/ pictures. I'm running a 6" Drop in the rear (without a C-Notch) and have no problems at all.

[ATrain707]

wwotr would these fit my truck? http://www.classicparts.com/1968-72-...ctinfo/51-505/

[wwotr]

Originally Posted by ATrain707

wwotr would these fit my truck? http://www.classicparts.com/1968-72-...ctinfo/51-505/

Yes they would and those are the same ones I used on my Truck.
I also ordered some LED #194 Red & Amber lights to go in them.
MUCH brighter than the regular #194 "Filiment" bulb.

[ATrain707]

these are the ones that are on the truck now http://www.classicparts.com/1968-72-...ctinfo/51-503/

also would these work on my 68? the stock headlights are 7in right? i wanna order these for my truck, anyone else running hids on there trucks without any problems? the one on ebay are also 7in
http://cgi.ebay.com/ebaymotors/7-Rou...Q5fAccessories

[ATrain707]

Ok. Thanx. My brother bought a 71 c10 from lake county n I'm lowering. For him
Posted via Mobile Device

[wwotr]

So where in Lake County are you and/or your Bother? I was in Cobb.
Posted via Mobile Device

[ATrain707]

i live in redwood valley and my brother lives in healdsburg

[ATrain707]

we also just finished this motor for my truck, now we just gotta put it in

[steelscout]

@wwotr, I love the stance of your truck hoping mine will be like that.
thats a nice engine..love to see pics when your done

[ATrain707]

Yea ill post pic when I'm done
Posted via Mobile Device