Project X - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ironroad9c1 · 01-24-2011, 05:24 PM

YouTube - 1980 Custom deluxe

*87 chevy silverado* · 01-24-2011, 07:30 PM

looks good man both them look savable good luck on the projects

ironroad9c1 · 01-25-2011, 11:03 AM

the camper special sat in a field untouched for 17 years... biggest reason its so rusty.
Got the intake cleaned, Man it was nasty, Worked on it in the parts washer for 2 hours with dental tools getting all the crud off, got the back on, New side gaskets and couple of beads of right stuff sealant on the chinawalls to stop any end leaks and just waiting on the exhaust manifolds to get here today to finish it off so I can drop it in.

ironroad9c1 · 01-27-2011, 12:49 AM

Well engine is in and bolted up. Prolly be firing it over tomorrow. Pic in the AM

*87 chevy silverado* · 01-27-2011, 06:53 PM

Quote:

Originally Posted by ironroad9c1

ust waiting on the exhaust manifolds to get here today to finish it off so I can drop it in.

i got the exact same block as this where did u get that oil pan gasket cus mine has the spot where u can have the dipstick on eighter side...thanks in advance..... looks good btw

ironroad9c1 · 01-27-2011, 10:09 AM

Note the nice new China made exhaust manifolds... I was pissed cause the Ebay ad said they had the heat shield, and when I got it ...It didn't , so I tried chatting with a rep online and he kept telling me it never said that , even after I gave him the link AND quoted the exact phase from the ad, so I told him screw it, I'll wait 7 days and leave negative feedback. I really didn't care it was not on there , its just the fact that is stated it came with one.

Bell housing after a couple of hours with wire brushes and a dental pic. Painted with Cast Aluminum paint

Cast Iron paint

I like this cast Iron paint, It matches almost perfect with the brand new Manifolds

Just about ready to swing in

New clutch and pressure plate.

Nice clean bell housing

And she's in.. It was a pain trying to get the trans lined up with the bellhousing, So I'm back and forth under the truck trying the get everything line up Then I see the frigging transmission isn't even bolted to the crossmember...RRRRRR After a few choice words I got a bolt in the trans mount and lowered the jack from the front of the trans and it slipped right in....

*nbpro* · 01-27-2011, 03:01 PM

looking good keep da pics comeing

benoit454 · 01-27-2011, 08:29 PM

that's just the fel-pro one piece oil pan seals. You can buy them almost anywhere.

*87 chevy silverado* · 01-27-2011, 08:58 PM

Quote:

Originally Posted by benoit454

that's just the fel-pro one piece oil pan seals. You can buy them almost anywhere.

but if u look it has the dipstick on both sides

what year vehical did they come in??? i spent hour at the parts house looking for one and we ended up taking 2 cork ones and making it work but i need the info for later so i can get the right one

benoit454 · 01-27-2011, 09:32 PM

doesn't look lik ehis block has it for both though. my fel-pro kit where it has the cork ones has them setup for both sides, but I'm not sure on my 88 one piece gasket.

his block looks to me like DS dipstick only so that's pre 80.

*87 chevy silverado* · 01-27-2011, 09:36 PM

sorry i meant it has the holes for the dipstick on both sides

ironroad9c1 · 01-28-2011, 09:47 PM

Felpro Oil Pan Gasket Set

Part No. OS34510T

Advance auto, Set even comes with New bolts cause the original ones are prolly too short. Hold on to your wallet though its about 30 bucks. but order online, and chose to pick it up at the store and use DEALIO as the discount code, Pay online and just take your print out to the store and pick it up. That block is a 1978 target master 4 bolt. assembled in flint , not Mexico like the Newer 80 and up blocks. Fired her up today , Now I just have to put the rest of it back together.

*87 chevy silverado* · 01-28-2011, 09:52 PM

Thank u so much sept for some reason mine has mexico all over it.. sorry for taking up ur build thread...

ironroad9c1 · 01-29-2011, 10:01 AM

Is OK senior.....

*87 chevy silverado* · 01-29-2011, 10:05 AM

lol.. anyways wats next on the list?

ironroad9c1 · 01-31-2011, 09:08 AM

Git it fired up. Runs like a top, Now to swap out the core support and put a straight but rusty fender and fenderwell on for the timr being So I can drive it and bring the Special in So I can go over it .

ironroad9c1 · 02-07-2011, 11:02 PM

Its almost ready...

Punched the dent in the door out and got her washed up.

Before

After...

*87 chevy silverado* · 02-08-2011, 06:24 PM

like that u changed the gril

ironroad9c1 · 02-09-2011, 10:32 AM

Yea I'm gonna get some repop headlight bezels too.

ironroad9c1 · 02-23-2011, 05:22 PM

Well I had a old holley 650 DP someone had hacked the choke horn off of it ran good on the truck, but I see a guy on Craigslist with a holley 2 d projection system, asking for trades., Called him up and told him what I had , and he took the carb and 250 for the system ..lol In the process of installing it now.

he never even bothered to take it off the manifold..LMAO but its just a old cast iron EGR manifold., Nothing special.

75ChevyGuy · 02-23-2011, 06:58 PM

Trucks looking good!

Greenlee · 02-24-2011, 09:22 AM

Nice build! With your video it's kind of like a reality tv show.

Posted via Mobile Device

*87 chevy silverado* · 02-24-2011, 06:35 PM

Quote:

Originally Posted by Greenlee

Nice build! With your video it's kind of like a reality tv show.

Posted via Mobile Device

yea i thought that to

ironroad9c1 · 02-24-2011, 11:15 AM

Yea a bad one..lol

ironroad9c1 · 02-27-2011, 08:33 PM

Well. got the projection setup installed and running, All I can say is WOW.. I love fuel injection..lol I don't think I will ever own another carb. post a vid tomorrow if its not raining

01-24-2011, 07:30 PM	#2
87 chevy silverado Account Suspended Join Date: Apr 2009 Location: lexington South Carolina Posts: 2,124	Re: Project X looks good man both them look savable good luck on the projects

01-25-2011, 11:03 AM	#3
ironroad9c1 Master Hater Join Date: Apr 2006 Location: Temple,Tx. Posts: 402	Re: Project X the camper special sat in a field untouched for 17 years... biggest reason its so rusty. Got the intake cleaned, Man it was nasty, Worked on it in the parts washer for 2 hours with dental tools getting all the crud off, got the back on, New side gaskets and couple of beads of right stuff sealant on the chinawalls to stop any end leaks and just waiting on the exhaust manifolds to get here today to finish it off so I can drop it in. __________________ 1997 C1500 ECSB 4.3/NV3500 8.5 3.42 "This evening, all of you bleeding hearts... why don't just go ahead and hug yourself for the next 20 minutes or so, because there's a really good chance you're gonna be offended".- Captain Owen Honors Last edited by ironroad9c1; 01-25-2011 at 11:08 AM.

01-27-2011, 12:49 AM	#4
ironroad9c1 Master Hater Join Date: Apr 2006 Location: Temple,Tx. Posts: 402	Re: Project X Well engine is in and bolted up. Prolly be firing it over tomorrow. Pic in the AM __________________ 1997 C1500 ECSB 4.3/NV3500 8.5 3.42 "This evening, all of you bleeding hearts... why don't just go ahead and hug yourself for the next 20 minutes or so, because there's a really good chance you're gonna be offended".- Captain Owen Honors

01-27-2011, 10:09 AM	#6
ironroad9c1 Master Hater Join Date: Apr 2006 Location: Temple,Tx. Posts: 402	Re: Project X Note the nice new China made exhaust manifolds... I was pissed cause the Ebay ad said they had the heat shield, and when I got it ...It didn't , so I tried chatting with a rep online and he kept telling me it never said that , even after I gave him the link AND quoted the exact phase from the ad, so I told him screw it, I'll wait 7 days and leave negative feedback. I really didn't care it was not on there , its just the fact that is stated it came with one. Bell housing after a couple of hours with wire brushes and a dental pic. Painted with Cast Aluminum paint Cast Iron paint I like this cast Iron paint, It matches almost perfect with the brand new Manifolds Just about ready to swing in New clutch and pressure plate. Nice clean bell housing And she's in.. It was a pain trying to get the trans lined up with the bellhousing, So I'm back and forth under the truck trying the get everything line up Then I see the frigging transmission isn't even bolted to the crossmember...RRRRRR After a few choice words I got a bolt in the trans mount and lowered the jack from the front of the trans and it slipped right in.... __________________ 1997 C1500 ECSB 4.3/NV3500 8.5 3.42 "This evening, all of you bleeding hearts... why don't just go ahead and hug yourself for the next 20 minutes or so, because there's a really good chance you're gonna be offended".- Captain Owen Honors Last edited by ironroad9c1; 01-31-2011 at 09:09 AM.

01-27-2011, 03:01 PM	#7
nbpro Account Suspended Join Date: Dec 2008 Location: Huntsville,AL Posts: 2,119	Re: Project X looking good keep da pics comeing

01-27-2011, 08:29 PM	#8
benoit454 Chris Join Date: Nov 2004 Location: Monaville, WV Posts: 3,737	Re: Project X that's just the fel-pro one piece oil pan seals. You can buy them almost anywhere. __________________ Chris GIT R DONE!!!!!! Check out all our rides, http://www.cardomain.com/id/benwa454

01-27-2011, 09:32 PM	#10
benoit454 Chris Join Date: Nov 2004 Location: Monaville, WV Posts: 3,737	Re: Project X doesn't look lik ehis block has it for both though. my fel-pro kit where it has the cork ones has them setup for both sides, but I'm not sure on my 88 one piece gasket. his block looks to me like DS dipstick only so that's pre 80. __________________ Chris GIT R DONE!!!!!! Check out all our rides, http://www.cardomain.com/id/benwa454 Last edited by benoit454; 01-27-2011 at 09:33 PM.

01-27-2011, 09:36 PM	#11
87 chevy silverado Account Suspended Join Date: Apr 2009 Location: lexington South Carolina Posts: 2,124	Re: Project X sorry i meant it has the holes for the dipstick on both sides

01-28-2011, 09:47 PM	#12
ironroad9c1 Master Hater Join Date: Apr 2006 Location: Temple,Tx. Posts: 402	Re: Project X Felpro Oil Pan Gasket Set Part No. OS34510T Advance auto, Set even comes with New bolts cause the original ones are prolly too short. Hold on to your wallet though its about 30 bucks. but order online, and chose to pick it up at the store and use DEALIO as the discount code, Pay online and just take your print out to the store and pick it up. That block is a 1978 target master 4 bolt. assembled in flint , not Mexico like the Newer 80 and up blocks. Fired her up today , Now I just have to put the rest of it back together. __________________ 1997 C1500 ECSB 4.3/NV3500 8.5 3.42 "This evening, all of you bleeding hearts... why don't just go ahead and hug yourself for the next 20 minutes or so, because there's a really good chance you're gonna be offended".- Captain Owen Honors Last edited by ironroad9c1; 01-29-2011 at 10:01 AM.

01-28-2011, 09:52 PM	#13
87 chevy silverado Account Suspended Join Date: Apr 2009 Location: lexington South Carolina Posts: 2,124	Re: Project X Thank u so much sept for some reason mine has mexico all over it.. sorry for taking up ur build thread...

01-29-2011, 10:01 AM	#14
ironroad9c1 Master Hater Join Date: Apr 2006 Location: Temple,Tx. Posts: 402	Re: Project X Is OK senior..... __________________ 1997 C1500 ECSB 4.3/NV3500 8.5 3.42 "This evening, all of you bleeding hearts... why don't just go ahead and hug yourself for the next 20 minutes or so, because there's a really good chance you're gonna be offended".- Captain Owen Honors

01-29-2011, 10:05 AM	#15
87 chevy silverado Account Suspended Join Date: Apr 2009 Location: lexington South Carolina Posts: 2,124	Re: Project X lol.. anyways wats next on the list?

01-31-2011, 09:08 AM	#16
ironroad9c1 Master Hater Join Date: Apr 2006 Location: Temple,Tx. Posts: 402	Re: Project X Git it fired up. Runs like a top, Now to swap out the core support and put a straight but rusty fender and fenderwell on for the timr being So I can drive it and bring the Special in So I can go over it . __________________ 1997 C1500 ECSB 4.3/NV3500 8.5 3.42 "This evening, all of you bleeding hearts... why don't just go ahead and hug yourself for the next 20 minutes or so, because there's a really good chance you're gonna be offended".- Captain Owen Honors

02-07-2011, 11:02 PM	#17
ironroad9c1 Master Hater Join Date: Apr 2006 Location: Temple,Tx. Posts: 402	Re: Project X Its almost ready... Punched the dent in the door out and got her washed up. Before After... __________________ 1997 C1500 ECSB 4.3/NV3500 8.5 3.42 "This evening, all of you bleeding hearts... why don't just go ahead and hug yourself for the next 20 minutes or so, because there's a really good chance you're gonna be offended".- Captain Owen Honors

02-08-2011, 06:24 PM	#18
87 chevy silverado Account Suspended Join Date: Apr 2009 Location: lexington South Carolina Posts: 2,124	Re: Project X like that u changed the gril



Register or Log In To remove these advertisements.

02-09-2011, 10:32 AM	#19
ironroad9c1 Master Hater Join Date: Apr 2006 Location: Temple,Tx. Posts: 402	Re: Project X Yea I'm gonna get some repop headlight bezels too. __________________ 1997 C1500 ECSB 4.3/NV3500 8.5 3.42 "This evening, all of you bleeding hearts... why don't just go ahead and hug yourself for the next 20 minutes or so, because there's a really good chance you're gonna be offended".- Captain Owen Honors

02-23-2011, 05:22 PM	#20
ironroad9c1 Master Hater Join Date: Apr 2006 Location: Temple,Tx. Posts: 402	Re: Project X Well I had a old holley 650 DP someone had hacked the choke horn off of it ran good on the truck, but I see a guy on Craigslist with a holley 2 d projection system, asking for trades., Called him up and told him what I had , and he took the carb and 250 for the system ..lol In the process of installing it now. he never even bothered to take it off the manifold..LMAO but its just a old cast iron EGR manifold., Nothing special. __________________ 1997 C1500 ECSB 4.3/NV3500 8.5 3.42 "This evening, all of you bleeding hearts... why don't just go ahead and hug yourself for the next 20 minutes or so, because there's a really good chance you're gonna be offended".- Captain Owen Honors

02-23-2011, 06:58 PM	#21
75ChevyGuy GM Parts Guy Join Date: Jan 2011 Location: Attleboro MA Posts: 375	Re: Project X Trucks looking good! __________________ 1975 Chevrolet C-10 Custom Deluxe (DD/WIP) 1989 Chevrolet C1500 reg cab stepside (Winter Truck) 1977 Harley Davidson XLH 1000 (Summer Cruiser)

02-24-2011, 09:22 AM	#22
Greenlee Registered User Join Date: Jun 2004 Location: El Lago, TX Posts: 1,668	Re: Project X Nice build! With your video it's kind of like a reality tv show. Posted via Mobile Device

02-24-2011, 11:15 AM	#24
ironroad9c1 Master Hater Join Date: Apr 2006 Location: Temple,Tx. Posts: 402	Re: Project X Yea a bad one..lol __________________ 1997 C1500 ECSB 4.3/NV3500 8.5 3.42 "This evening, all of you bleeding hearts... why don't just go ahead and hug yourself for the next 20 minutes or so, because there's a really good chance you're gonna be offended".- Captain Owen Honors

02-27-2011, 08:33 PM	#25
ironroad9c1 Master Hater Join Date: Apr 2006 Location: Temple,Tx. Posts: 402	Re: Project X Well. got the projection setup installed and running, All I can say is WOW.. I love fuel injection..lol I don't think I will ever own another carb. post a vid tomorrow if its not raining __________________ 1997 C1500 ECSB 4.3/NV3500 8.5 3.42 "This evening, all of you bleeding hearts... why don't just go ahead and hug yourself for the next 20 minutes or so, because there's a really good chance you're gonna be offended".- Captain Owen Honors

Register or Log In To remove these advertisements.