Best way to raise the bed floor

[smashingchuck]

Alright guys, It's time to at least start thinking about the next phase of the truck, and that will be raising the bed floor. I'm not sure how to do it really. My original thought was to leave the stock crossmembers in, and space it up with 3"x1" x1/16 wall square tubing, but I really don't like that idea now too much. My major concerns are strength and form. The body work on my outer skins is already done so I hope I don't have to weld on those or atleast keep it to a minimum.

Here are my goals:
*I would like to run stock wheel tubs.
*I would like to do a flat floor, and have the inner bedsides run straight down on the inside. I know I will have to make a skeleton out of 1x1 but I'm just not sure what to attatch it to on the outside peremeter???
*I'm not sure exactly how high I want to raise it, but I was thinking 3". I would still have to run a separate raised "notch cover" if this was the case.

I cannot, for the life of me, figure out what to do for a fuel tank. I cant put it where the factory saddle bombs go cause thats where my air tanks are, my exhaust runs all the way out the back so theres no room where a blazer tank would go, and I really would like to conceal it somewhere rather than mount it to the inside of the bed. Any ideas on this??

any pictures, ideas on fuel cells/tanks, and ideas on how to attatch this new floor to the existing skins would be great. Right now the bed is assembled but all the floor/inner fenders have been cut out. The factory crossmembers are still in place.

[maxxxy]

ive been thinking about this too. i think for a gas tak you are probably going to have to modify your exhaust and do a blazer tank or a fuel cell. check out this link on the raised bed floor

http://67-72chevytrucks.com/vboard/s...d.php?t=409466

[smashingchuck]

That is just not an option.
Posted via Mobile Device

[N2TRUX]

Originally Posted by smashingchuck

That is just not an option.]

Unfortunately your going to have to consider some sort of compromise. With you set on a full length exhuast out the back, a custom built tank is in your future
Posted via Mobile Device

[smashingchuck]

Originally Posted by N2TRUX

Unfortunately your going to have to consider some sort of compromise. With you set on a full length exhuast out the back, a custom built tank is in your future
Posted via Mobile Device

I've already given in to the custom tank, just got to find a place to put it....
Posted via Mobile Device

[4x4fab]

put it between the rails, in the front part of your bed. Just build it to have clearence for the driveshaft. I think that's my plans on my 64'.

[smashingchuck]

Originally Posted by 4x4fab

put it between the rails, in the front part of your bed. Just build it to have clearance for the drive shaft. I think that's my plans on my 64'.

Kinda what I'm leaning twoards but I don't want my drive shaft any where near it. Glad I've already got the hoop.

[smashingchuck]

I just don't consider that a safe place to mount a gas tank on a bagged truck. Too close to the ground and too much danger of something puncturing it or even dragging it. Maybe I can have one made that fits between the frame rails in the front of the bed, under the raised bed floor? To me that's the safest place to put it.
Posted via Mobile Device

[smashingchuck]

Hers what my bed looks like now....

Posted via Mobile Device

[N2TRUX]

Post your frame pics from the rear again. That will give us an idea of what your working with. Take a look at what Keith (n2billet) is doing on Hazel.

[smashingchuck]

Originally Posted by N2TRUX

Post your frame pics from the rear again. That will give us an idea of what your working with. Take a look at what Keith (n2billet) is doing on Hazel.

these are the only ones I have handy.

[smashingchuck]

thanks for the pics that looks really nice. I found another pic...

[67cheby]

now i see your exhaust dilema, how about hanging a round gas tank like my air tank

[smashingchuck]

Originally Posted by 67cheby

now i see your exhaust dilema, how about hanging a round gas tank like my air tank

That location, to me is ideal. I could probably fit one in where you mounted your fuel cell if I raise the bed floor higher. Which brings me to another decesion... My initial plan was to raise the floor only 3", and have a cover over the notch and bridge. Do you fellas think it would look better with a floor thats raised more, and is completely flat, or a floor that is a little deeper but has a cover over the notch. The more I raise the floor, the easier its going to be to get a fuel cell mounted under there. Also, does anbody agree with me that mounting the tank near the back is safetly concern? I see a lot of people doing it.

[jasonhall]

My tank is going to be in the rear but raised up quite a bit. I like the look of a raised bed floor with no notch. looks cleaner to me

[smashingchuck]

Originally Posted by jasonhall

My tank is going to be in the rear but raised up quite a bit. I like the look of a raised bed floor with no notch. looks cleaner to me

I like it too, what I dont like is when the floor is too high. So I guess the question should be how high is too high?

[jlaird]

heres some pictures I've saved over the years that might give you some ideas.

[jlaird]

couple more

[smashingchuck]

wow nate that looks really nice. I've already determined I'm not going to be able to do this part of my build without getting a bead roller.
Posted via Mobile Device

[54Caddy]

nate how did you guys mount the bed. did you build an understrructure or what?

[jasonhall]

thats slick!