TX mostly complete cab

[dammitmitchell]

69 c 20 cab
floor shifter 2wd

HERE WE GO!
list of parts i know are good (all worked when cab was pulled)


seat frame/ springs is 75 bucks plus shipping it's pretty dang new.. only a few years old.
the foam is useable but had some sun exposure. (free w seat and shipping or 20 bucks separate)

steering column $50
------------------------------------------each piece below 25 bucks!-----------------------
----------------------------------------------PLUS SHIPPING!-----------------------------
gauges and bezel(it's allright but complete..)
side vents driver and pass ( complete and operable)
steering column (floor shifter manual)
tranny/shifter hump (2WD)
UN MOLESTED dash board metal..
BOTH driver and passenger visors with retainer clips (they are in great shape!)
ignition and bezel(no key)
ash tray
glove box door (hinge needs cleaning but has button and works)
pedals (need cleaning)
gas pedal rubber (good condition) (5bucks)
inner door panels are useable, one had a rust hole BELOW the arm rest, it is not visible when arm rest is mounted
has all 4 knobs for the doors (window crank, and door handles)
right fender (outer) is rust free needs to be sandblasted and repainted of course.
pass door is complete W glass and vent window, driver quality rust free (50 bucks plus shipping)
hood hinges (surface rusted but operate well)
hood release (pin assys work well)
windshield washer bottle holder (great shape surface rust only)

heater only cab, engine bay box (great shape) interior boxes (need washing but in good shape)
front turn signal housings with 1 lens and both pigtails
DOOR hinges! all 4 all 4 are in good opertating order, i would definatley use these on my own driver if they needed it.
radiator retaining brackets (surface rust)
center grille bracket (surface rust)
corner fender to rad support brackets (surface rust)
have the wiring for the dome bulb assy complete, un nicked, original GM wire.

annnnd...
RAD support! (cancer free!!!!!!!)
the windshield cowl is PERFECT! the antenna hole is un molested, the wiper holes are great and the worst part is it's two layers of paint! (seriously ONLY 20 bucks!)


umm if there is anything NOT listed feel free to ask .. please save haggeling and barter options for PM.. thanks!

[dammitmitchell]

-----PICTURE TIME!!!!!!!!!!!!!!!!!!!!---------------------------------

[Leroy-B1]

whats the passenger inner fender like?

[frankenstein69]

Dibs on the grille pending price

[frankenstein69]

I see a grille, how much?

[dammitmitchell]

[jwgeorge]

Is that a three-on-the-tree steering column? If so, how much for it? How much do you want for the doors? I may be interested in the cab itself too, how much for the cab?

[dammitmitchell]

[dammitmitchell]

ttt

[WV72]

you going to cut up the cab any? I am looking for some of the floor next to rocker pannels. from the toe wall to the back of the cab.

[mac72]

Mitchell,Are both doors in good shape & for sale? or just the one?
Mac

[dammitmitchell]

only pass door is good shape the left has a hole in it from a pic axe or something..

[dammitmitchell]

more then willing to cut for you. and it'll e cut with a die grinder not a torch.
give me a picture and measurements and i'll send you a peice if it's good. also i can send pictures of the floor for the areas you want. they are not perfect.. they are patchable.

[WV72]

I will get some pics and up load them tonight and see what you want. Thanks

[68 IRON]

What is the condition of the fan shroud? If its good and the right price I'll take it.

[dammitmitchell]

heya fan shroud was broken off on the bottom half, so i tossed it sorry

[CaptRMW]

First up for the heater control without cables pending price shipped to 34689. Thanks, Roger

[dammitmitchell]

pm sent

[WV72]

Here is the pic of the floor I need. I borrowed the pic from Teeitup. the previous owner did a bad job at repairing the floor. So I need from the toe board to the back of the cab.

[dammitmitchell]

--------------------

[kellytheaker]

the outer door handles ? good shape i could possibly use the heater controls as well with the cables complete

[WV72]

I am good. thanks for looking.

[dammitmitchell]

Originally Posted by kellytheaker

the outer door handles ? good shape i could possibly use the heater controls as well with the cables complete

the heater controls have been paid for.
but i do still have the control cables etc.. and complete box.
outer door handles are good and working order. driver quality id have to calculate the shipping to canada (i heard they like to screw you guys over)

[bigbadchev72]

How much for these as patch panels. I need the drivers side as well cut the same way. The jimmy I just bought has a patch welded over the firewall So I just need the metal with the heater box holes.

[kellytheaker]

it is expensive . try a quote to N0B-2K0 for the handles and see where we get thanks its when you put down a value that taxes need met with .