Will 20x8 wheels bolt up without rubbing? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

72addict · 04-03-2003, 04:56 PM

Thinking of putting 20x8 Eagle 212's on my 1972 swb GMC 2wd that has coils. Will they clear without rubbing? Anybody have these wheels on there truck? Any pics out there? Thanks

Alexis · 04-03-2003, 05:58 PM

whats the back spacing on them? 20x8 should do it wihtout rubbing.

72addict · 04-06-2003, 03:36 PM

9/16" I think. Does that sound right?

Alexis · 04-06-2003, 03:43 PM

9/16?? are you sure... that wheel must really stick out. What you do is you measure from the where the hub would mount to the edge of the wheel. make sure the wheel is flat and measure going up. Hope that helps, but 9/16" would not be the back spacing unless someone realy messed up. With an 8inch wheel the back spacing should from my best guess 4 inches and the rear 4.5 inches.

If you want a picture on how to measure it i can post one.

72addict · 04-06-2003, 08:17 PM

Ok imadumba$$. Backspacing is 5".

Alexis · 04-06-2003, 08:23 PM

wait.......yeah they should tuck in the fender.....but i dont know how they will look. maybe they'll stick in a little too much.

Dreaminator · 04-06-2003, 08:43 PM

Goto www.wheelsforless.com as it has a great tech center that will help you with proper back spacing. If it is a normal 8" rim with 9/16 that translates to 4" plus 9/16 in most cases. Trust me, make sure. Because it is next to impossible to return rims once they have been mounted. Triple check back inside too.

mrchev · 04-07-2003, 03:47 AM

Yes, the wheels will work.

I have 20x10 on the rear, and 20x8 on the front.

You can see them on the truck at: myrodshop.com/blazer.html

NSANE68!!! · 04-07-2003, 02:41 PM

It has to be a min of 4.5" backspacing. TRUST ME!! I put my 20's on and they tuck but it is close 5" backspacing would be better and if it is a 9/16 with only 4" of backspace they WON'T tuck.

GREEN70-72 · 04-07-2003, 02:54 PM

I WOULD HAVE TO SAY YES

Josh292 · 04-27-2003, 04:19 AM

20X8 This is not my truck. But I am buying those rims for my 72.
Hope this helps

Dreaminator · 04-27-2003, 11:33 AM

Just make sure you turn them hard right and left to the stops with mounted rubber. Also, depending on how much you drop the front, be careful that fended well rim does not grab the tire tread when turning andbacking down a ramp. Mine did. Went to 17s instead.

casey · 04-27-2003, 02:22 PM

green70-72 got anymore pics love your trucks

imaindianoutlaw · 04-27-2003, 05:46 PM

doesnt it make a differance on what rear you have in your truck? my 69 is a few inches shorter than the 71 parts truck I have! and are the trucks all the same width in the front?

04-03-2003, 04:56 PM	#1
72addict Registered User Join Date: Mar 2000 Location: Mason MI, 48854 (strikezone of the mitten) Posts: 894	Will 20x8 wheels bolt up without rubbing? Thinking of putting 20x8 Eagle 212's on my 1972 swb GMC 2wd that has coils. Will they clear without rubbing? Anybody have these wheels on there truck? Any pics out there? Thanks __________________ 1957 Cameo

04-06-2003, 03:36 PM	#3
72addict Registered User Join Date: Mar 2000 Location: Mason MI, 48854 (strikezone of the mitten) Posts: 894	9/16" I think. Does that sound right? __________________ 1957 Cameo

04-06-2003, 08:17 PM	#5
72addict Registered User Join Date: Mar 2000 Location: Mason MI, 48854 (strikezone of the mitten) Posts: 894	Ok imadumba$$. Backspacing is 5". __________________ 1957 Cameo

04-06-2003, 08:43 PM	#7
Dreaminator Dreaminator Join Date: Feb 2003 Location: Broken Arrow, Oklahoma Posts: 156	Goto www.wheelsforless.com as it has a great tech center that will help you with proper back spacing. If it is a normal 8" rim with 9/16 that translates to 4" plus 9/16 in most cases. Trust me, make sure. Because it is next to impossible to return rims once they have been mounted. Triple check back inside too. __________________ The Dreaminator Daily Driver 1971 Cheyenne 10 Lwb Tilt/Tac 402 .030 TH400.

04-07-2003, 03:47 AM	#8
mrchev Registered User Join Date: Jan 2003 Location: fort worth, Texas Posts: 24	20x8 wheels Yes, the wheels will work. I have 20x10 on the rear, and 20x8 on the front. You can see them on the truck at: myrodshop.com/blazer.html

04-03-2003, 05:58 PM	#2
Alexis Member since 2000 Join Date: Dec 2000 Location: Mountain View Ca / Mexico Posts: 7,874	whats the back spacing on them? 20x8 should do it wihtout rubbing.

04-06-2003, 03:43 PM	#4
Alexis Member since 2000 Join Date: Dec 2000 Location: Mountain View Ca / Mexico Posts: 7,874	9/16?? are you sure... that wheel must really stick out. What you do is you measure from the where the hub would mount to the edge of the wheel. make sure the wheel is flat and measure going up. Hope that helps, but 9/16" would not be the back spacing unless someone realy messed up. With an 8inch wheel the back spacing should from my best guess 4 inches and the rear 4.5 inches. If you want a picture on how to measure it i can post one.

04-06-2003, 08:23 PM	#6
Alexis Member since 2000 Join Date: Dec 2000 Location: Mountain View Ca / Mexico Posts: 7,874	wait.......yeah they should tuck in the fender.....but i dont know how they will look. maybe they'll stick in a little too much.

04-07-2003, 02:41 PM	#9
NSANE68!!! SLICER AND DICIER Join Date: May 2001 Location: Quuen Creek Posts: 1,383	It has to be a min of 4.5" backspacing. TRUST ME!! I put my 20's on and they tuck but it is close 5" backspacing would be better and if it is a 9/16 with only 4" of backspace they WON'T tuck. Attached Images __________________ 01 Tahoe 22's 2/4 drop and tv's 68 chevy money pit 51 chevy belair 95 Honda 900RR 05 GMC Siearra (company truck)

04-07-2003, 02:54 PM	#10
GREEN70-72 Registered User Join Date: Feb 2002 Location: CRESTVIEW,FL,US Posts: 355	I WOULD HAVE TO SAY YES Attached Images __________________ 70 SWB, 4/6" DROP,20X8 & 20X9.5. BOYD TIMELESS 5,93 BURB POWER SEATS, BILLET SPECIALTIES STEERING WHEELS. SOON TO BE VOTECH AND TBI POWERED. O YEA AND WAL-MART IS THE DEVIL!!!

04-27-2003, 04:19 AM	#11
Josh292 Registered User Join Date: Apr 2003 Location: Faribault, Mn Posts: 97	20X8 20X8 This is not my truck. But I am buying those rims for my 72. Hope this helps Attached Images

04-27-2003, 11:33 AM	#12
Dreaminator Dreaminator Join Date: Feb 2003 Location: Broken Arrow, Oklahoma Posts: 156	Just make sure you turn them hard right and left to the stops with mounted rubber. Also, depending on how much you drop the front, be careful that fended well rim does not grab the tire tread when turning andbacking down a ramp. Mine did. Went to 17s instead. __________________ The Dreaminator Daily Driver 1971 Cheyenne 10 Lwb Tilt/Tac 402 .030 TH400.

04-27-2003, 02:22 PM	#13
casey Registered User Join Date: Jan 2003 Location: Kelowna B.C. Canada Posts: 2,048	green70-72 got anymore pics love your trucks Last edited by casey; 04-27-2003 at 02:53 PM.

04-27-2003, 05:46 PM	#14
imaindianoutlaw GMC SHORT FLEET F/S Join Date: Jun 2000 Location: SOUTH WILLIAMSPORT PENNSYLVANNIA Posts: 2,117	doesnt it make a differance on what rear you have in your truck? my 69 is a few inches shorter than the 71 parts truck I have! and are the trucks all the same width in the front? __________________ CHARLES WADE HEIN HVACR FOREMAN. LEWISBURG U.S.P.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.