Building a 64 street strip truck, need advice

[Arekusu]

Hey all,

I am hopeing to run about a 12.5 in the 1/4, am I on the right path? I bought a 454 bbc to drop into the truck, I know I probally could have done it with my small block but I kind of wanted to build a big block , and it was the right price.

Specs : 454 .030 over

cam I'm planning to buy:
comp cam xtreme energy XE268H
224 / 230 duration @ .050
.515 / .520 lift
110 lobe seperation

heads: oval ports # 3964290
2.06 intake 1.72 exhaust
closed chamber
(would rather not chane the heads if I don't have to)

flat top pistons

Edelbrock preformer RPM intake

holley 750

-- What I "think" I know--

I need to make somewhere between 450-500 hp to run a 12.5 in the 1/4 and go somewhere near 115mph

Big blocks like compression, and most preformance cams require it. I'm guessing that with a compressed head gasket thickness of .041 I should have somewhere near 9:1 compression?

My stock crank and connecting rods should be good for up to 600 hp. So I don't feel like I should change anything except adding ARP main bolts (or studs?) and ARP wave loc connecting rod bolts. Should I balance the rotating assembly?

Anyone have a 168 tooth flywheel recomendation and clutch and pressure plate recomendation that will work well? I have a stock 168 tooth flywheel now, do I need a better one? More rotating mass (heavey flywheel) is better for drag racing correct?

I'm running a TKO 500 5 speed (still street driven, don't want an auto) but I was thinking I should use 3.55, or 3.40 to use more of the big blocks torque band for my cam choice.

Tire size - I was thinking about a 29'' tire by 10 - 10.5'' wide. Hopefully this will let it hook up? Are stamped steel rims ok to accompolish this?

Suspension - So far stock except for 4'' lowering springs in the back, adjustable panhard bar and new shocks,

rolling into the next topic

rear differential -

Planning on a Moser 9'' of some sort, with the new wave track locker. 35 spline axles.. hopefully I never break it.


So the goal is 12.5 in the 1/4. I still plan on driving this on the street a few times a week, rain or shine. So am I close? What should I change?

Alex

[KQQL IT]

Read up on super 73' post's
He has hooking up a trailing arm rear and needed mods to front suspension setup which is equally important to hooking a truck up.
Posted via Mobile Device

[Captainfab]

Your engine combo is identical to the 461 in my '66 Suburban, with the exception of the heads. IMO you're not going to get to 12.5 with that engine combo.

[Arekusu]

What would I need to change to get to 12.5? Is the cam not enough?

[Arekusu]

Bump


I'm looking at other builds others have done and they have a bit more cam. Is this why? Could my heads support more cam effeciently?

Should this be moved to the engine section?

Alex

[Captainfab]

I'm not an engine expert, but I would say you will need to upgrade your heads to 2.19/1.88 valves. I'm not sure what the 290 heads flow as compared to say the 049/781 heads, so I don't know if that would really help you or not. Then you will need to bump up the cam a bit, and at the same time the compression needs to come up to support the larger cam.

Or you could spray it as BR3W CITY mentioned.

And of course with the increased power comes the challenge of getting it to hook.

Originally Posted by Arekusu

Bump


I'm looking at other builds others have done and they have a bit more cam. Is this why? Could my heads support more cam effeciently?

Should this be moved to the engine section?

Alex

[BR3W CITY]

1. Are you sure about the compression? If the engine has been redone, are you sure the heads have not been altered, or that there were no modifications to the deck height or anything like that?

More cam might help, but you could spray a little on what you have and hit your time goals if you can hook. Seen plenty of cars go WAY faster on a 10.5" tire. Not sure about how a stamped wheel holds up, but I have welded steel wheels and they hold up just fine.

[BigDan3131]

If you need more weight in the rear put not only the tank behind the axle but also your battery/s too. If that ends up not being enough I would look for ballast bars/plates you can use or instead of a back bumper get a 3" x 6" or 2" x 4" box tubing that fits across the width of your truck. Weld two bungs, one on top the other on bottom and fill it with either lead shot or steel shot. You get a heavy duty bumper and ballast bar at the same time.

[Arekusu]

Ya, I think I'd use the ballest plates if I need too. We'll see.