CO '72 8" lift and a pair of 454s

[ryanroo]

i have some stuff clogging up my garage and since my plans for the 72 don't involve any of this stuff i would like to get rid of it.

i have a set of Skyjacker 8" lift springs for a '72 K-20. i put these on my green truck probably 10-12 years ago. i drove it for maybe 500 miles over the year following and then it just sat. so, the springs are in very good condition as far as their service. they have some surface rust but the bushings are all in great shape. this both the front and rear springs.

$500 for the set.

i have a 3" correction block for a dana 60 and a 4 inch drop drag link that i will toss in for $50 as well.
i will do whatever i can on my end to help with shipping but the cost is on the buyer.



this is a 454 out of a 1986 K-30. it runs with no funny noises. i have no idea what the mileage is. i bought a truck for parts and this was the engine in it. it was in my jeep for a year when i decided to swap to TBI in the process i stumbled on a complete tbi 454 so i just swapped engines. i have the rochester carb and the HEI for it they are not installed in the pic.

$300 bucks



definately prefer pick-up


this is a GENV 454. one piece rear main. it was removed from a motorhome with 30k on it. the bore is factory and in great shape. it has speedpro hypereutectic pistons with a 9.6:1 w/110cc chamber compression ratio. factory crank and rods. no cam. ready for you to finish however fits your needs best.

$800.

again, prefer pick up



i also have a pull out 4x4 th400 that i will call a core. not sure on its history it was another parts truck thing.

$100

pick up preffered pictures on request, it is hiding in my garage.

SM465, adapter and ten spline np205 working condition but all could use a refurb, slimy and dirty with fixed 1350 rear output and the 1310 spicer yoke style front output

$150

pickup prefered. photos on request. looks like any other 465/205 combo.


thanks
Ryan

[junkcarguy]

Sign me up for the 86 carb motor what part of co are you in
Posted via Mobile Device

[ryanroo]

Sorry. I thought I had that in the listing. All of this is in bayfield Co. An hour and change west of wolf creek pass and fifteen miles east of Durango
Thanks
Posted via Mobile Device

[ryanroo]

ttt

[bigboi]

would you be interested in shipping the 86 454 shipping cost of course would be on me send me your zip if interested i am willing to pay you for your time and labor for pallet

[ryanroo]

i could ship it, but i would prefer not to have to deal with any of the logistics. paletizing it and getting it on the truck would not be an issue. it would be leaving from where i work zip is 81303 and there is a forklift to load it with there. junkcarguy said he wanted it, but i have PMed him and have not heard back from him. i will send him another message tomorrow and if he doesnt get back with me soon after i will assume he passed on it.

ryan

[bigboi]

ok kool i will check on a shipping quote and wait on your reply thanks

[ryanroo]

Originally Posted by bigboi

ok kool i will check on a shipping quote and wait on your reply thanks

i have heard nothing from junkcarguy, so as far as i am concerned it is yours if you still wish to go forward.

Ryan

[ryanroo]

i sent the message, but i didnt get it sent till today. sorry for the delay but i will let you know if i hear back in the next day or two.

Ryan

[72blazer_mud_bogger]

can I see a pic of the drag link please

[ryanroo]

Originally Posted by 72blazer_mud_bogger

can I see a pic of the drag link please

will try to get you a pic. it is in the parts section of my garage which is pretty disorganized. might be tomorrow.

ryan

[ryanroo]

i looked and looked for the drag link. i finally remembered that it was still attached to the steering arm.

pics

[mrdana60]

pm sent

[walkintall54]

Interested in the springs do you still have them?