CST door emblem mounting hole location - The 1947 - Present Chevrolet & GMC Truck Message Board Network

shawno72 · 10-13-2011, 06:54 PM

Hello. I am looking to install a couple "custom" emblems on my 1968 doors and was wondering where to drill the holes. What size are the holes and how do they mount into the doors?
Name: $(KGrHqF,!k8E6Bp3oG4EBOklpTe7+!~~60_3.jpg
Views: 1970
Size: 45.9 KB

Name: $(KGrHqF,!k8E6Bp3oG4EBOklpTe7+!~~60_3.jpg
Views: 1970
Size: 45.9 KB

Here is one example
Name: IMG_2552.JPG
Views: 1276
Size: 38.4 KB

**chewychevy67** · 10-13-2011, 07:24 PM

They mount with speed nuts just like the chrome piece that goes over the tailgate handle.. If nobody posts before tomorrow or Saturday morning i will post pics of the hardware and measurements . Rod.

shawno72 · 10-13-2011, 07:38 PM

Ok Rod. Thank you. I kinda figured that they mounted the same way as the tailgate trim piece that goes over the handle. I just haven't been able to find the little hardware piece that pushes into the door.

67chevy1series · 10-13-2011, 08:20 PM

rod is half correct...... 68s use the same little nuts that you screw emblems on and in 67 they use the speed nuts that you just push in.... the cool thing is you can get 67 emblems take the speed nuts off and use the same nuts for emblems, and screw them on the back... it will be like brand new and very tight. and not loose from the wear of the pot metal. on my 67 the bottom of the emblem rides very close to the body line under the emblem, and has a taller gap from the top of them emblem to the body line above it.... it is also 14 inches from the back of the door to the front of the emblem. hope this helps.

shawno72 · 10-13-2011, 11:50 PM

Well the emblems I am expecting in the mail are off of a 68 so I guess I will need to fit my fingers or a wrench inside the door to install the speed nuts? Any tips to make it any easier? Thank you so much Rick for the measurements.
Posted via Mobile Device

67chevy1series · 10-14-2011, 12:06 AM

i wish i could have helped more.... well i just installed these in my dads doors yesterday! lol what i did was carefully put the nut on the 3/8s wrench and pushed the nuts on the studs really hard so they didnt fall off the i turned them righty tighty... remmember one at a time and do it very very delicatly..... also i did this by going in between the outer door skina dn the inner doors skin at the window sill.

shawno72 · 10-14-2011, 12:16 AM

That was my plan to go through the top and not remove the door panel. Sounds easy enough. I'll let you know the results.
Posted via Mobile Device

67chevy1series · 10-14-2011, 01:22 AM

ok let me know! get some pics to!

**too much stuff** · 10-14-2011, 09:20 PM

Should just be barrel clips for those emblems. (push ins) I don't think i have seen nuts on any of those emblems even through 72 on the blazers.

otsenre · 10-14-2011, 09:29 PM

Quote:

Originally Posted by too much stuff

Should just be barrel clips for those emblems. (push ins) I don't think i have seen nuts on any of those emblems even through 72 on the blazers.

Eric, I think you are right, just like the custom camper emblems by the way,thats my door you are using as sample LOL

**too much stuff** · 10-14-2011, 09:33 PM

Quote:

Originally Posted by otsenre

Eric, I think you are right, just like the custom camper emblems by the way,thats my door you are using as sample LOL

Actually, the upper door scrpits for "custom" and "camper" i have seen with barrel clips or smaller speed nuts.

shawno72 · 10-14-2011, 10:53 PM

Quote:

Originally Posted by otsenre

Eric, I think you are right, just like the custom camper emblems by the way,thats my door you are using as sample LOL

Would it be possible for your door to once again be a sample and could you pull a measurement for the location of the holes. Lol

Posted via Mobile Device

shawno72 · 10-14-2011, 10:22 PM

Ok. I got my custom emblems in the mail today and sure enough there was one barrel clip on one of the studs. So next question where can I get four of those barrel clips at? I'm at lowes right now and no luck. Also is there anyone who can give me the measurements of where to drill the holes? I guess I can eyeball it if I have to but would rather it be exact. Thanks guys.
Posted via Mobile Device

shawno72 · 10-15-2011, 09:59 AM

Ttt
Posted via Mobile Device

otsenre · 10-15-2011, 10:14 AM

Quote:

Originally Posted by shawno72

Ttt
Posted via Mobile Device

holing tape measure at style line (see pics) upside down pic is holding tape measre from other side of door, hope this helps Name: IMG_2566.JPG
Views: 1040
Size: 41.4 KB

Name: IMG_2566.JPG
Views: 1040
Size: 41.4 KB

Name: IMG_2567.JPG
Views: 1168
Size: 41.2 KB

Name: IMG_2568.JPG
Views: 1015
Size: 37.5 KB

Name: IMG_2569.JPG
Views: 997
Size: 40.8 KB

Name: IMG_2570.JPG
Views: 1058
Size: 44.5 KB

shawno72 · 10-15-2011, 10:46 AM

Quote:

Originally Posted by otsenre

holing tape measure at style line (see pics) upside down pic is holding tape measre from other side of door, hope this helps Attachment 814512

Attachment 814513

Attachment 814514

Attachment 814515

Attachment 814516

Thank you that does help, but I am still at a loss as to where to find these barrel clips. Also was hoping to get an excact location of the mounting holes so that I am not trying to eyeball where to drill.
Name: barrel1.jpg
Views: 907
Size: 41.0 KB

Name: barrel1.jpg
Views: 907
Size: 41.0 KB

Name: barrel2.jpg
Views: 912
Size: 37.9 KB

shawno72 · 10-15-2011, 11:31 AM

ttt

shawno72 · 10-15-2011, 02:21 PM

Ok so I found the clips at a place called Auto Industrial Paint right here in Lodi. Only $3 for a bag of six. Ready to drill just as soon as I can get the location of the holes.

shawno72 · 10-15-2011, 04:44 PM

Anyone have the hole measurements yet?? dying to install these. lol

**too much stuff** · 10-15-2011, 06:40 PM

I checked 5 doors i have here and they vary from 13 1/4" to 14 1/4" from the back of the door like in post 4 or the first pic from ernesto. Just decide on your measurement, hold the emblem up and figure your hole location.

bigbadchev72 · 10-15-2011, 06:44 PM

Quote:

Originally Posted by shawno72

Anyone have the hole measurements yet?? dying to install these. lol

Take a piece of cardboard trim it to the size of the emblem and push it on the backside so the studs go through the cardboard.

Take the cardboard with the holes in it, measure on the door like the pictures above.

Take a sharpie and press it against the holes in the cardboard, then drill out the sharpie marks on the door.

shawno72 · 10-15-2011, 06:50 PM

Quote:

Originally Posted by bigbadchev72

Take a piece of cardboard trim it to the size of the emblem and push it on the backside so the studs go through the cardboard.

Take the cardboard with the holes in it, measure on the door like the pictures above.

Take a sharpie and press it against the holes in the cardboard, then drill out the sharpie marks on the door.

Duh why didn't I think of that?? Will do tonight. Thank you guys for all your help.

smorg007 · 10-15-2011, 07:26 PM

This is in the assembly manual but not real helpful.

shawno72 · 10-15-2011, 08:34 PM

Success!!
Before with holes drilled.
Name: photo (2).jpg
Views: 940
Size: 33.2 KB

And after with emblem installed.
Name: photo.jpg
Views: 972
Size: 33.0 KB

Thank you guys for all your help.

shawno72 · 10-17-2011, 12:59 PM

Today I am replacing the P255/70r15 up front with some P245/60r15. That will give it a
1" drop up front.

10-13-2011, 06:54 PM	#1
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	CST door emblem mounting hole location Hello. I am looking to install a couple "custom" emblems on my 1968 doors and was wondering where to drill the holes. What size are the holes and how do they mount into the doors? Here is one example __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

10-13-2011, 07:24 PM	#2
chewychevy67 Senior Member Join Date: Jan 2010 Location: Here Posts: 5,551	Re: CST door emblem mounting hole location They mount with speed nuts just like the chrome piece that goes over the tailgate handle.. If nobody posts before tomorrow or Saturday morning i will post pics of the hardware and measurements . Rod.

10-13-2011, 07:38 PM	#3
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: CST door emblem mounting hole location Ok Rod. Thank you. I kinda figured that they mounted the same way as the tailgate trim piece that goes over the handle. I just haven't been able to find the little hardware piece that pushes into the door. __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

10-13-2011, 08:20 PM	#4
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: CST door emblem mounting hole location rod is half correct...... 68s use the same little nuts that you screw emblems on and in 67 they use the speed nuts that you just push in.... the cool thing is you can get 67 emblems take the speed nuts off and use the same nuts for emblems, and screw them on the back... it will be like brand new and very tight. and not loose from the wear of the pot metal. on my 67 the bottom of the emblem rides very close to the body line under the emblem, and has a taller gap from the top of them emblem to the body line above it.... it is also 14 inches from the back of the door to the front of the emblem. hope this helps. Attached Images

10-13-2011, 11:50 PM	#5
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: CST door emblem mounting hole location Well the emblems I am expecting in the mail are off of a 68 so I guess I will need to fit my fingers or a wrench inside the door to install the speed nuts? Any tips to make it any easier? Thank you so much Rick for the measurements. Posted via Mobile Device __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

10-14-2011, 12:06 AM	#6
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: CST door emblem mounting hole location i wish i could have helped more.... well i just installed these in my dads doors yesterday! lol what i did was carefully put the nut on the 3/8s wrench and pushed the nuts on the studs really hard so they didnt fall off the i turned them righty tighty... remmember one at a time and do it very very delicatly..... also i did this by going in between the outer door skina dn the inner doors skin at the window sill.

10-14-2011, 12:16 AM	#7
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: CST door emblem mounting hole location That was my plan to go through the top and not remove the door panel. Sounds easy enough. I'll let you know the results. Posted via Mobile Device __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

10-14-2011, 01:22 AM	#8
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: CST door emblem mounting hole location ok let me know! get some pics to!

10-14-2011, 09:20 PM	#9
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,787	Re: CST door emblem mounting hole location Should just be barrel clips for those emblems. (push ins) I don't think i have seen nuts on any of those emblems even through 72 on the blazers. __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto

10-14-2011, 10:22 PM	#13
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: CST door emblem mounting hole location Ok. I got my custom emblems in the mail today and sure enough there was one barrel clip on one of the studs. So next question where can I get four of those barrel clips at? I'm at lowes right now and no luck. Also is there anyone who can give me the measurements of where to drill the holes? I guess I can eyeball it if I have to but would rather it be exact. Thanks guys. Posted via Mobile Device __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

10-15-2011, 09:59 AM	#14
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: CST door emblem mounting hole location Ttt Posted via Mobile Device __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

10-15-2011, 11:31 AM	#17
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: CST door emblem mounting hole location ttt __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

10-15-2011, 02:21 PM	#18
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: CST door emblem mounting hole location Ok so I found the clips at a place called Auto Industrial Paint right here in Lodi. Only $3 for a bag of six. Ready to drill just as soon as I can get the location of the holes. __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

10-15-2011, 04:44 PM	#19
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: CST door emblem mounting hole location Anyone have the hole measurements yet?? dying to install these. lol __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

10-15-2011, 06:40 PM	#20
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,787	Re: CST door emblem mounting hole location I checked 5 doors i have here and they vary from 13 1/4" to 14 1/4" from the back of the door like in post 4 or the first pic from ernesto. Just decide on your measurement, hold the emblem up and figure your hole location. __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto



Register or Log In To remove these advertisements.

10-15-2011, 07:26 PM	#23
smorg007 Registered User Join Date: May 2010 Location: Redding, Ca Posts: 371	Re: CST door emblem mounting hole location This is in the assembly manual but not real helpful. Attached Images

10-15-2011, 08:34 PM	#24
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: CST door emblem mounting hole location Success!! Before with holes drilled. And after with emblem installed. Thank you guys for all your help. __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

10-17-2011, 12:59 PM	#25
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: CST door emblem mounting hole location Today I am replacing the P255/70r15 up front with some P245/60r15. That will give it a 1" drop up front. __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

Register or Log In To remove these advertisements.