Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
01-13-2012, 07:20 PM | #1 |
Registered User
Join Date: Dec 2011
Location: Gilbert, Arizona
Posts: 47
|
HELP!!!! Torsion bar Removal
I have been working on my truck now for about 3 month now and making great progress but ran into a stand still on the torsion bars, I would like to remove them from the control arms but have not had any luck getting them to move at all, I assume they have never been off the truck due to the amout of grease and dirt that was welded on them.
I would like to know if anyone has removed them before, and if so do I need to press them out or should they come out just with brute force Im hoping someone will be able to help on this becouse I will be sending the parts out to be powdercoated next week and I would like to have it apart by then!!!!! Thanks for all you help guys and gals!!!!
__________________
1962 Chevrolet S/B Fleet side Engine: 283 Transmission: 3 speed manual 2 do list !!!!!! Frame off-2 1/2" front , 4" rear Rebuild engine (or find a 327), 700R4 Trans, relocate gas tank, Bed wood |
01-13-2012, 07:28 PM | #2 |
Senior Enthusiast
Join Date: Feb 2007
Location: Spokane Valley, WA
Posts: 8,356
|
Re: HELP!!!! Torsion bar Removal
Mine never did come out. After I pulled the suspension I gave them several good solid whacks with a sledge hammer just to see if I could remove them at all, and to make it easier to transport to the dumps. They never budged so eventually I gave up. Soaking with WD40 didn't help either. Maybe something like PB Blaster would have made a difference. A press may be the only solution.
|
01-13-2012, 07:33 PM | #3 |
Registered User
Join Date: Dec 2011
Location: Gilbert, Arizona
Posts: 47
|
Re: HELP!!!! Torsion bar Removal
I have been soaking them in liquid wrench for about the last 2 days and going to try again tonight, I hope I dont have to go to that extreme though, what did you do for the front end?
__________________
1962 Chevrolet S/B Fleet side Engine: 283 Transmission: 3 speed manual 2 do list !!!!!! Frame off-2 1/2" front , 4" rear Rebuild engine (or find a 327), 700R4 Trans, relocate gas tank, Bed wood |
01-13-2012, 08:16 PM | #4 | |
Senior Enthusiast
Join Date: Feb 2007
Location: Spokane Valley, WA
Posts: 8,356
|
Re: HELP!!!! Torsion bar Removal
Quote:
Here's a link showing what it took to do the conversion: http://67-72chevytrucks.com/vboard/s...d.php?t=366828 |
|
01-14-2012, 12:39 PM | #5 |
Registered User
Join Date: Sep 2009
Location: American Fork Utah
Posts: 119
|
Re: HELP!!!! Torsion bar Removal
Heat up the lower a arms where the torsion bars go into them with a torch...get them red hot and then hit them with an air hammer. They will slide right out.
|
01-13-2012, 07:57 PM | #6 |
100% gearhead
Join Date: Apr 2007
Location: Boise, Idaho
Posts: 313
|
Re: HELP!!!! Torsion bar Removal
I unbolted the rear of mine and then used heat, A LOT of penetrating lube, a length of pipe as a drift, and a gigantic hammer. It took a while and made me tired too.
__________________
Imperial Kustom LLC Meridian Idaho. I never stopped playing with cars, they just got bigger. |
Bookmarks |
|
|