Fuel filler neck grommet - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Daddy'O · 01-25-2012, 09:54 AM

Holly cow! – that grommet for the cab and fuel filler neck is a pain to install. I got it done but there has to be a secret to an easier installation. I used a soapy water solution and some dental pick style tools to pull the grommet in from the back side. It turned out good but man it was more difficult than I expected. Anyone care to share their installation secrets?

chopnchaneled · 01-25-2012, 10:17 AM

Subcribed !

**RenoKeene** · 01-25-2012, 10:28 AM

I put mine in from the outside, soaped it up, and taped up a flat blade screwdriver. After I got it started I took a prybar wrapped in a towel and a baggie, slipped it down the neck and slowly, carefully wiggled the neck around as I pushed on the grommet with the screwdriver. Worked like a charm and only took a couple of minutes.

68gmsee · 01-25-2012, 10:43 AM

I've replaced mine at least 3-4 times in my two trucks. First couple of times it was a pain but basically did it like everyone by lubing it with silicone oil and pushing it in from the outside.

I also did it a couple of times from the inside while I had the tank out for cleaning. It seemed easier that way. First time I pushed it outward from the inside and the second time I installed it in the opening and lubed the neck of the tank and pushed it through.

Bottom line, take your time, use plenty of lube and don't use sharp objects.

Indyuke · 01-25-2012, 01:35 PM

I'm not trying to be dirty and this is the only picture I could find, but I just recently put the fuel tank back into my truck and I used this stuff. I put the fuel tank in first, then put the grommet in. The filler neck was slightly off center, and I had a hard time with the tighter side, but all in all it only took about 5 minutes. It's been raining good lately, and it doesn't seem to leak.

**Classic Heartbeat** · 01-25-2012, 01:41 PM

I remove the tank, install the grommet, lube the gas filler neck and then push the tank back through the installed grommet. I have also heard of some guys roping it in like a windshield. WES

pat 70/71 · 01-25-2012, 02:15 PM

I have only done one. I put I put the collar in a pot with water and boiled it. I slipped it right on the neck with gloves on, And it didn't take to much effort as I recall. (that was twenty years ago!) And it was an oem collar. cheers, Pat

Brian LI · 01-26-2012, 03:02 PM

Quote:

Originally Posted by pat 70/71

I have only done one. I put I put the collar in a pot with water and boiled it. I slipped it right on the neck with gloves on, And it didn't take to much effort as I recall.

I recently did mine using the dish soap and force it with a screwdriver described by many folks above.

If I ever have to do it again I'll definitely try this!

AirSpeed · 01-25-2012, 05:06 PM

Quote:

Originally Posted by Indyuke

I'm not trying to be dirty and this is the only picture I could find, but I just recently put the fuel tank back into my truck and I used this stuff. I put the fuel tank in first, then put the grommet in. The filler neck was slightly off center, and I had a hard time with the tighter side, but all in all it only took about 5 minutes. It's been raining good lately, and it doesn't seem to leak.

I use similar stuff! It is way more slippery than soap and it rinses right off. Just stay away from the flavored stuff, you don't want people licking your filler neck! (well maybe some of you do but I don't judge!)
Posted via Mobile Device

68gmsee · 01-25-2012, 08:10 PM

Quote:

Originally Posted by Indyuke

..........The filler neck was slightly off center, and I had a hard time with the tighter side...

Mine was also and I used a long 2" dowel to straighten it. I shoved it and gently pushed on it to center the neck.

black_sheep454 · 01-25-2012, 02:13 PM

I've had good luck with soaking it in warm soapy water when putting it on from the outside.
Posted via Mobile Device

AirSpeed · 01-25-2012, 05:11 PM

I have changed mine several times because they keep cracking after a month or two, I don't mean to hijack but has anyone found a supplier that sells a good grommet for a 72GMC? I have bought them from Classic Parts, LMC and one more that escapes me right now. Each of them sent me a free replacement but they all cracked as well. It's getting kind of old replacing them all the time. The last one I installed leaves a black streak down the cab corner every time it rains or snows.
Posted via Mobile Device
Posted via Mobile Device

69sixpackbee · 01-25-2012, 07:53 PM

I used K-Y...don't laugh. I really did

Gotta use it on something!

68gmsee · 01-25-2012, 08:15 PM

Quote:

Originally Posted by AirSpeed

I have changed mine several times because they keep cracking after a month or two, I don't mean to hijack but has anyone found a supplier that sells a good grommet for a 72GMC? Posted via Mobile Device
Posted via Mobile Device

Try Classic Heartbeat. Mine has gone through a dry, hot Texas summer and still no cracks and black smudges.

eightbanger · 01-25-2012, 07:59 PM

Lube for "intimate contact"...it must be Truck love.

69sixpackbee · 01-25-2012, 08:24 PM

Quote:

Originally Posted by eightbanger

Lube for "intimate contact"...it must be Truck love.

That bugger was the dog's bollocks

eightbanger · 01-26-2012, 03:19 PM

Quote:

Originally Posted by 69 1/2 Six Pack Bee

That bugger was the dog's bollocks

Now there's an English saying...how'd that get over there.

I've often wanted to use it, but assumed nobody would get it, or would think I had an unhealthy interest K9 Testicles

I have used Vaseline/Petroleum Jelly, and with very little effort they slip right on.

68gmsee · 01-26-2012, 08:18 PM

[QUOTE=eightbanger;5147317]...I've often wanted to use it, but assumed nobody would get it, or would think I had an unhealthy interest K Testicles

...QUOTE]

I see your point. I googled the meaning.

69sixpackbee · 01-26-2012, 08:33 PM

Gotta love them Brits!

hayhauler71 · 01-25-2012, 09:09 PM

3m silicone paste on the grommet and push and twist 180 no problem. The silicone is also used to protect rubber and my grommet looks new after 7 years.

oldspowered67C10 · 01-26-2012, 03:16 AM

I bought a original GM one (came in a GM bag)from Wes a few weeks back, couldnt have been easier to install.

Daddy'O · 01-26-2012, 02:04 PM

Great feedback!

I never knew the slippery stuff or ky jelly had other uses – LMAO. I think I might have a difficult time explaining that one to my wife.

I will definitely keep these in mind when I do my next one. My 72 4x4 will need to be replaced (as well as many other items) when I start her restoration.

Thanks!

**Tom Vogel** · 01-27-2012, 10:55 AM

Take it to dinner first, then some Barry White.

01-25-2012, 09:54 AM	#1
Daddy'O Registered User Join Date: Jan 2012 Location: Whitesboro, Texas Posts: 932	Fuel filler neck grommet Holly cow! – that grommet for the cab and fuel filler neck is a pain to install. I got it done but there has to be a secret to an easier installation. I used a soapy water solution and some dental pick style tools to pull the grommet in from the back side. It turned out good but man it was more difficult than I expected. Anyone care to share their installation secrets? __________________ Cheers - Wayne Our Shop Build - http://67-72chevytrucks.com/vboard/s...d.php?t=620966 '55 Wagon Build - http://67-72chevytrucks.com/vboard/s...d.php?t=689157 1971 Cheyenne Super Ochre/White LWB 350 Auto - my son's truck "Nancy" 1972 GMC K2500 Custom 4X4 Olive LWB 400 SB 4-speed -"Greenie" - Restoration to begin after the '55 Nothing sucks more than that moment during an argument when you realize you're wrong.

01-25-2012, 10:17 AM	#2
chopnchaneled Registered User Join Date: Dec 2009 Location: Atlanta, Ga. Posts: 1,050	Re: Fuel filler neck grommet Subcribed ! __________________ I don't think we get smarter as we get older. We just run out of Stupid things to do.

01-25-2012, 10:28 AM	#3
RenoKeene Florida Edition Join Date: Oct 2010 Location: Fruitland Park, FL Posts: 4,028	Re: Fuel filler neck grommet I put mine in from the outside, soaped it up, and taped up a flat blade screwdriver. After I got it started I took a prybar wrapped in a towel and a baggie, slipped it down the neck and slowly, carefully wiggled the neck around as I pushed on the grommet with the screwdriver. Worked like a charm and only took a couple of minutes. __________________ 70 GMC Short Stepside "Rose"-An American Beauty: Factory 402/TH400, AM/FM, AC, Tilt, Tach, Buckets, Posi, PS, PB, 3-5 Drop, Complete Resto-Rod 67 C-20 Slant Back Wrecker "Mad Max" 67 C-10 Ratrod "Step-N-Wolf" 71 Serro Scotty Sportsman camper "Scotty" 97 LT1 Z28 "The Hornet" Link to more pics of "Rose" http://67-72chevytrucks.com/vboard/a...p?albumid=1684 Check out my "Cheap Tricks" thread and add to it if you can, lots of good info there. http://67-72chevytrucks.com/vboard/s...d.php?t=489394

01-25-2012, 10:43 AM	#4
68gmsee Active Member Join Date: Jul 2007 Location: Centrally located between Houston, Austin and Waco. BCS area. Posts: 7,947	Re: Fuel filler neck grommet I've replaced mine at least 3-4 times in my two trucks. First couple of times it was a pain but basically did it like everyone by lubing it with silicone oil and pushing it in from the outside. I also did it a couple of times from the inside while I had the tank out for cleaning. It seemed easier that way. First time I pushed it outward from the inside and the second time I installed it in the opening and lubed the neck of the tank and pushed it through. Bottom line, take your time, use plenty of lube and don't use sharp objects.

01-25-2012, 01:35 PM	#5
Indyuke Registered User Join Date: Feb 2008 Location: Lake Stevens, WA Posts: 623	Re: Fuel filler neck grommet I'm not trying to be dirty and this is the only picture I could find, but I just recently put the fuel tank back into my truck and I used this stuff. I put the fuel tank in first, then put the grommet in. The filler neck was slightly off center, and I had a hard time with the tighter side, but all in all it only took about 5 minutes. It's been raining good lately, and it doesn't seem to leak.

01-25-2012, 01:41 PM	#6
Classic Heartbeat Project Junkie! Fishing Poor!! Join Date: Dec 1999 Location: Olympia,Wa. 98512 Posts: 10,766	Re: Fuel filler neck grommet I remove the tank, install the grommet, lube the gas filler neck and then push the tank back through the installed grommet. I have also heard of some guys roping it in like a windshield. WES __________________ On-line catolog Classic Heartbeat Pickup Parts WEHEPP@comcast.net Call us Toll Free (888) 338-2502 Like Us on Facebook No appointment necessary. 72 BB Chevy Custom Deluxe / Custom Camper 67 I-6 (Soon to be 5.7 LS1) Panel 68 BB Chevy Short Bed 72 6.0 LQ9 Short Bed Chevy 4X4 Olympia's fastest growing truck parts supplier. Olympia's home for Wayward Chevys

01-25-2012, 02:15 PM	#7
pat 70/71 Registered User Join Date: Nov 2009 Location: newbury park california Posts: 1,038	Re: Fuel filler neck grommet I have only done one. I put I put the collar in a pot with water and boiled it. I slipped it right on the neck with gloves on, And it didn't take to much effort as I recall. (that was twenty years ago!) And it was an oem collar. cheers, Pat

01-25-2012, 02:13 PM	#11
black_sheep454 Registered User Join Date: May 2011 Location: Lebanon, Mo. Posts: 1,315	Re: Fuel filler neck grommet I've had good luck with soaking it in warm soapy water when putting it on from the outside. Posted via Mobile Device __________________ 1968 chevy lwb, getting ready to join forces with the 70 gmc 1970 gmc swb, getting ready to be a 68 chevy swb 1971 gmc lwb 2500 2wd Sierra Grande 1988 chevy 1-ton crew cab 2wd waiting for a 12v cummins

01-25-2012, 05:11 PM	#12
AirSpeed Registered User Join Date: Jul 2007 Location: Fall River California Posts: 2,026	Re: Fuel filler neck grommet I have changed mine several times because they keep cracking after a month or two, I don't mean to hijack but has anyone found a supplier that sells a good grommet for a 72GMC? I have bought them from Classic Parts, LMC and one more that escapes me right now. Each of them sent me a free replacement but they all cracked as well. It's getting kind of old replacing them all the time. The last one I installed leaves a black streak down the cab corner every time it rains or snows. Posted via Mobile Device Posted via Mobile Device

01-25-2012, 07:53 PM	#13
69sixpackbee Registered User Join Date: Jan 2001 Location: Sabinal, Texas Posts: 1,706	Re: Fuel filler neck grommet I used K-Y...don't laugh. I really did Gotta use it on something!

01-25-2012, 07:59 PM	#15
eightbanger 454 MAKES IT ROAR Join Date: Jan 2008 Location: Essex, U.K Posts: 2,701	Re: Fuel filler neck grommet Lube for "intimate contact"...it must be Truck love. __________________ Nigel. An American living in a British body. 1971 Chevy Cheyenne 10 454 "In a time of universal deceit, telling the truth becomes a revolutionary act." - George Orwell "When injustice becomes law, resistance becomes duty" - Thomas Jefferson No more pain. 03.12.60 -- 12.28.10 http://www.youtube.com/Eightbanger

01-26-2012, 08:18 PM	#18
68gmsee Active Member Join Date: Jul 2007 Location: Centrally located between Houston, Austin and Waco. BCS area. Posts: 7,947	Re: Fuel filler neck grommet [QUOTE=eightbanger;5147317]...I've often wanted to use it, but assumed nobody would get it, or would think I had an unhealthy interest K Testicles...QUOTE] I see your point. I googled the meaning.

01-26-2012, 08:33 PM	#19
69sixpackbee Registered User Join Date: Jan 2001 Location: Sabinal, Texas Posts: 1,706	Re: Fuel filler neck grommet Gotta love them Brits!

01-25-2012, 09:09 PM	#20
hayhauler71 Registered User Join Date: Aug 2009 Location: St. Paul MN. Posts: 1,996	Re: Fuel filler neck grommet 3m silicone paste on the grommet and push and twist 180 no problem. The silicone is also used to protect rubber and my grommet looks new after 7 years. __________________ Fuzzy

01-26-2012, 03:16 AM	#21
oldspowered67C10 Registered User Join Date: Jan 2006 Location: Cherry Valley,Ca Posts: 468	Re: Fuel filler neck grommet I bought a original GM one (came in a GM bag)from Wes a few weeks back, couldnt have been easier to install.



Register or Log In To remove these advertisements.

01-26-2012, 02:04 PM	#22
Daddy'O Registered User Join Date: Jan 2012 Location: Whitesboro, Texas Posts: 932	Re: Fuel filler neck grommet Great feedback! I never knew the slippery stuff or ky jelly had other uses – LMAO. I think I might have a difficult time explaining that one to my wife. I will definitely keep these in mind when I do my next one. My 72 4x4 will need to be replaced (as well as many other items) when I start her restoration. Thanks! __________________ Cheers - Wayne Our Shop Build - http://67-72chevytrucks.com/vboard/s...d.php?t=620966 '55 Wagon Build - http://67-72chevytrucks.com/vboard/s...d.php?t=689157 1971 Cheyenne Super Ochre/White LWB 350 Auto - my son's truck "Nancy" 1972 GMC K2500 Custom 4X4 Olive LWB 400 SB 4-speed -"Greenie" - Restoration to begin after the '55 Nothing sucks more than that moment during an argument when you realize you're wrong.

01-27-2012, 10:55 AM	#23
Tom Vogel 2WD Jimmy Join Date: Mar 2005 Location: Davis County, Utah Posts: 2,565	Re: Fuel filler neck grommet Take it to dinner first, then some Barry White.

Register or Log In To remove these advertisements.