TX Dana 60 Rear W/ Power Loc Posi - The 1947 - Present Chevrolet & GMC Truck Message Board Network

lynnfield · 11-27-2012, 04:53 PM

Dana 60 rear end, two piece power loc posi (the rebuildable one) good clutches, 4.10 gears, everything looks good inside $400. Pick up only. IMO, it looks to have been rebuilt not long ago, clutches feel real good, and they went to a lot of trouble to paint the entire housing. I have this for sale locally as well. Greg

KrashMan454 · 11-27-2012, 08:39 PM

Wow ! Why couldn't this be for a coil spring truck and with 3.73or 3.42 gears? I would be all over it.

**special-K** · 11-27-2012, 09:54 PM

Is this a 6 or 8-lug rear?

**w314speed** · 11-27-2012, 11:04 PM

Greg is this for a 2wd or 4wd? The perches look like 2wd. Thanks, Dan

lynnfield · 11-27-2012, 11:34 PM

It's from an 8 lug 3/4 ton 2wd truck, the one I'm currently parting in another thread. Am I way off on the price? This is the first one I've had, so I had to do some searching to figure out some kind of value. This would work in a 4wd?

Thanks, Greg

**leddzepp** · 11-28-2012, 12:36 AM

I think that is a great price!
Posted via Mobile Device

bronze 72 super · 11-28-2012, 01:35 AM

Your price is very reasonable. Too bad no shipping, oh well!!

**special-K** · 11-28-2012, 06:58 AM

That's a decent complete/bolt-in posi axle price for someone needing just that (or even moving spring perches for 4wd). For someone wanted it just for the posi or another ratio it wouldn't be worth it,especially considering the labor required. I was hoping for a 6-lug and really need a coil-type.

*BAT* · 11-28-2012, 09:04 AM

Quote:

Originally Posted by special-K

That's a decent complete/bolt-in posi axle price for someone needing just that (or even moving spring perches for 4wd). For someone wanted it just for the posi or another ratio it wouldn't be worth it,especially considering the labor required. I was hoping for a 6-lug and really need a coil-type.

Here is a nice article about putting a leaf spring rear end in a coil spring truck: http://www.earlyclassic.com/tech.aspx?category=Swappin'%20And%20Droppin'

And a bump for a nice rear end

Hertzdaddy · 11-28-2012, 10:38 AM

Dang. Don't you have relatives in VA you need to visit soon?

lynnfield · 11-28-2012, 04:51 PM

Sorry about the shipping everyone. I can get it banded to a pallet if someone want's to work out their own shipping and pick up. We can probably arrange it to be picked up from my work where there will be a fork lift available for loading. Best I can do. Greg

eagleuh1 · 11-29-2012, 01:34 AM

Engine hoist and chanins work for loading also. Thats how I loaded mine. Also good price for this. Jim

lynnfield · 12-01-2012, 12:34 PM

I can include the drive shaft if that helps anyone. From a LWB with a th400 trans. Greg

lynnfield · 12-07-2012, 07:00 PM

Ttt

nobolt · 12-07-2012, 11:27 PM

i will check next next week with a shop i deal with. pretty sure i could get it dropped there. but the shipping costs may kill that.

if you decide to split it i am interested in the locker

lynnfield · 12-12-2012, 11:20 PM

Bump

lynnfield · 12-15-2012, 09:49 PM

Ttt

lynnfield · 01-06-2013, 11:10 PM

Ttt

coops714x4 · 01-07-2013, 12:09 AM

Greg, I'm pretty interested, just don't know when I could get down there to pick it up. Coop

lynnfield · 01-07-2013, 01:24 AM

Coop, if you want to work something out, I have no problem hanging on to it til you can get down here. Greg

coops714x4 · 01-07-2013, 11:37 PM

PM sent

lynnfield · 01-08-2013, 12:53 AM

The drive shaft was sold and is no longer available. Greg

Black71Shorty · 01-08-2013, 09:39 PM

Hey Greg,...looking at the pictures on the ring gear what you have is a 3.73 ratio. Meaning 41 teeth on the ring gear and 10 teeth on the pinion gear. A 4.11 ratio has 37 and 9. Hope this helps and good luck with the sale!

**leddzepp** · 01-08-2013, 09:57 PM

Quote:

Originally Posted by Black71Shorty

Hey Greg,...looking at the pictures on the ring gear what you have is a 3.73 ratio. Meaning 41 teeth on the ring gear and 10 teeth on the pinion gear. A 4.11 ratio has 37 and 9. Hope this helps and good luck with the sale!

41/10 = 4.10
37/9 = 4.11

He has a 4.10 rear end...
Posted via Mobile Device

Black71Shorty · 01-08-2013, 10:13 PM

Sorry Greg,.. I looked at it wrong.

You do have a 4.11 gear. My eyes and math aren't what they use to be! I'm getting over the flu so that may have had a little to do with also. A 37 ring gear and 9 pinion is also a 4.11 ratio. Anyway...goodluck with it!!

11-27-2012, 04:53 PM	#1
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Dana 60 Rear W/ Power Loc Posi Dana 60 rear end, two piece power loc posi (the rebuildable one) good clutches, 4.10 gears, everything looks good inside $400. Pick up only. IMO, it looks to have been rebuilt not long ago, clutches feel real good, and they went to a lot of trouble to paint the entire housing. I have this for sale locally as well. Greg Attached Images

11-27-2012, 08:39 PM	#2
KrashMan454 Registered User Join Date: Jan 2009 Location: Terry, Mississippi. Posts: 225	Re: Dana 60 Rear W/ Power Loc Posi Wow ! Why couldn't this be for a coil spring truck and with 3.73or 3.42 gears? I would be all over it.

11-27-2012, 09:54 PM	#3
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Dana 60 Rear W/ Power Loc Posi Is this a 6 or 8-lug rear? __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

11-27-2012, 11:04 PM	#4
w314speed Senior Member Join Date: Jun 2005 Location: atlanta Posts: 2,315	Re: Dana 60 Rear W/ Power Loc Posi Greg is this for a 2wd or 4wd? The perches look like 2wd. Thanks, Dan

11-27-2012, 11:34 PM	#5
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: Dana 60 Rear W/ Power Loc Posi It's from an 8 lug 3/4 ton 2wd truck, the one I'm currently parting in another thread. Am I way off on the price? This is the first one I've had, so I had to do some searching to figure out some kind of value. This would work in a 4wd? Thanks, Greg

11-28-2012, 12:36 AM	#6
leddzepp Moderator Join Date: May 2007 Location: Southern Cal Posts: 20,031	Re: Dana 60 Rear W/ Power Loc Posi I think that is a great price! Posted via Mobile Device __________________ 1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man RIP FleetsidePaul

11-28-2012, 01:35 AM	#7
bronze 72 super Registered User Join Date: Sep 2007 Location: Rufus Oregon Posts: 1,186	Re: Dana 60 Rear W/ Power Loc Posi Your price is very reasonable. Too bad no shipping, oh well!!

11-28-2012, 06:58 AM	#8
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Dana 60 Rear W/ Power Loc Posi That's a decent complete/bolt-in posi axle price for someone needing just that (or even moving spring perches for 4wd). For someone wanted it just for the posi or another ratio it wouldn't be worth it,especially considering the labor required. I was hoping for a 6-lug and really need a coil-type. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

11-28-2012, 10:38 AM	#10
Hertzdaddy Registered User Join Date: Oct 2008 Location: Montpelier, VA Posts: 315	Re: Dana 60 Rear W/ Power Loc Posi Dang. Don't you have relatives in VA you need to visit soon?

11-28-2012, 04:51 PM	#11
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: Dana 60 Rear W/ Power Loc Posi Sorry about the shipping everyone. I can get it banded to a pallet if someone want's to work out their own shipping and pick up. We can probably arrange it to be picked up from my work where there will be a fork lift available for loading. Best I can do. Greg

11-29-2012, 01:34 AM	#12
eagleuh1 Registered User Join Date: Jul 2009 Location: Russellville, Arkansas Posts: 1,699	Re: Dana 60 Rear W/ Power Loc Posi Engine hoist and chanins work for loading also. Thats how I loaded mine. Also good price for this. Jim

12-01-2012, 12:34 PM	#13
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: Dana 60 Rear W/ Power Loc Posi I can include the drive shaft if that helps anyone. From a LWB with a th400 trans. Greg

12-07-2012, 07:00 PM	#14
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: Dana 60 Rear W/ Power Loc Posi Ttt

12-07-2012, 11:27 PM	#15
nobolt Registered User Join Date: Oct 2011 Location: Algonac, MI 48001 Posts: 1,848	Re: Dana 60 Rear W/ Power Loc Posi i will check next next week with a shop i deal with. pretty sure i could get it dropped there. but the shipping costs may kill that. if you decide to split it i am interested in the locker __________________ Dave "... government even in its best state is but a necessary evil. Thomas Paine "It wasn't a lie, it was ineptitude with insufficient cover." Donald Draper (Mad Men)

12-12-2012, 11:20 PM	#16
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: Dana 60 Rear W/ Power Loc Posi Bump



Register or Log In To remove these advertisements.

12-15-2012, 09:49 PM	#17
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: Dana 60 Rear W/ Power Loc Posi Ttt

01-06-2013, 11:10 PM	#18
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: Dana 60 Rear W/ Power Loc Posi Ttt

01-07-2013, 12:09 AM	#19
coops714x4 Registered User Join Date: Mar 2011 Location: Cement Oklahoma Posts: 916	Re: Dana 60 Rear W/ Power Loc Posi Greg, I'm pretty interested, just don't know when I could get down there to pick it up. Coop __________________ 1971 K20, Coop's beast (project) 1972 C30 wrecker, "Big Ernest" (SOLD) 1975 K5 Blazer (wife's toy) she got it in the divorce 2014 Street Glide Special 1983 K20 Big Block, auto (work horse)

01-07-2013, 01:24 AM	#20
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: Dana 60 Rear W/ Power Loc Posi Coop, if you want to work something out, I have no problem hanging on to it til you can get down here. Greg

01-07-2013, 11:37 PM	#21
coops714x4 Registered User Join Date: Mar 2011 Location: Cement Oklahoma Posts: 916	Re: Dana 60 Rear W/ Power Loc Posi PM sent __________________ 1971 K20, Coop's beast (project) 1972 C30 wrecker, "Big Ernest" (SOLD) 1975 K5 Blazer (wife's toy) she got it in the divorce 2014 Street Glide Special 1983 K20 Big Block, auto (work horse)

01-08-2013, 12:53 AM	#22
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: Dana 60 Rear W/ Power Loc Posi The drive shaft was sold and is no longer available. Greg

01-08-2013, 09:39 PM	#23
Black71Shorty Registered User Join Date: May 2009 Location: Ft. Worth, Texas...”Where the West begins” Posts: 424	Re: Dana 60 Rear W/ Power Loc Posi Hey Greg,...looking at the pictures on the ring gear what you have is a 3.73 ratio. Meaning 41 teeth on the ring gear and 10 teeth on the pinion gear. A 4.11 ratio has 37 and 9. Hope this helps and good luck with the sale!

01-08-2013, 10:13 PM	#25
Black71Shorty Registered User Join Date: May 2009 Location: Ft. Worth, Texas...”Where the West begins” Posts: 424	Re: Dana 60 Rear W/ Power Loc Posi Sorry Greg,.. I looked at it wrong. You do have a 4.11 gear. My eyes and math aren't what they use to be! I'm getting over the flu so that may have had a little to do with also. A 37 ring gear and 9 pinion is also a 4.11 ratio. Anyway...goodluck with it!!

Register or Log In To remove these advertisements.