rear bumper question... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Moline_Puller · 12-10-2012, 02:26 PM

Hi Guys,

Every time I come on here, I am amazed at how much info is on here...I learn something new every time!

This might be a dumb question, I'm not sure. After looking through a lot of pics of '67-72's, I can't remember seeing another one with a rear bumper like the one on my truck...here is a pic.

Is this a GM bumper? Or did someone swap it out? I actually kinda like it, because it isn't as big as some of the step bumpers.

Thanks for the help! I'm just kinda curious as to what it is and if it is correct for the truck.

Chris

50bomb · 12-10-2012, 02:30 PM

I prefer the sports bumpers but I havent found one that I could paint. This is a heavy duty bumper I had on my truck but Junked the bumper a year ago. Now I have no bumper and regret junking it because I do not have a place to put my license plate. I could definatley live with a bumper like the ONE you have on your truck.

Moline_Puller · 12-10-2012, 02:34 PM

Hey 50bomb,

Yeah, I was kinda planning on putting a roll pan on it, but I kinda like this bumper...it isn't as big as a lot of the step bumpers.

yuccales · 12-10-2012, 02:59 PM

That bumper looks good, might even look good chrome!

**truckster** · 12-10-2012, 03:24 PM

That's not a factory bumper. It's aftermarket or dealer-installed. They weren't too rare way back when, but you don't see a lot of them anymore.

SS Tim · 12-10-2012, 03:31 PM

From the angles of the ends and general simplicity of it I would say it was homemade. Not that is a bad thing just saying it is probably fairly unique. A picture or two of the bottom side and brackets would probably confirm this.

If I were keeping this on a truck a little flattening on the ends,say an inch would keep it from hurting so much when you run into it.

Also when you need something identified a picture of the part in question is more helpful than the truck as a whole.

The stripes are they the factory D89 stripes? They would be on the SPID label if original.

Moline_Puller · 12-10-2012, 03:27 PM

Thanks truckster! That answers my question...I didn't think it was a GM bumper. I haven't seen any other ones like it.

*Mister-B* · 12-10-2012, 03:36 PM

Check out my bumper restoration thread. http://67-72chevytrucks.com/vboard/s...d.php?t=551823

For less than about 20 bucks, you can get that thing looking like new
Posted via Mobile Device

Moline_Puller · 12-10-2012, 03:45 PM

Hey Mister-B, Thanks for the advice. Did you prep your bumper (sandbalst, wire brush, etc?) before your primered it?

*Mister-B* · 12-10-2012, 04:23 PM

Quote:

Originally Posted by Moline_Puller

Hey Mister-B, Thanks for the advice. Did you prep your bumper (sandbalst, wire brush, etc?) before your primered it?

I really didn't do much. I believe I used a wire brush quickly, and then wiped it clean with a rag. That primer is good stuff. It soaked in really well and sealed it up
Posted via Mobile Device

Moline_Puller · 12-10-2012, 04:48 PM

Thanks again. I'll have to give that primer a try

*Mister-B* · 12-10-2012, 04:59 PM

Quote:

Originally Posted by Moline_Puller

Thanks again. I'll have to give that primer a try

May as well. You're looking at around several hundred bucks for a non sport replacement, when you figure in tax and shipping
Posted via Mobile Device

Seamus · 12-10-2012, 06:56 PM

Bumper looks after market - see similar on farm trucks. I have a similar one I took off of my '56 except it wraps around the back fenders a little. They are heavier than stock.

hugger6933 · 12-10-2012, 09:39 PM

They are aftermarket or dealer bumpers. Most dealers offered them as a courtesy to their new truck buyers back in the day. The price you had to pay for having the "free" bumper was the dealers name and town engraved and hilighted in another color in the bumper. I have some of these bumpers from the dealers from the towns around me . One of my 70's [the swb] has one. I also have two or three more on the ground at the shop. Years ago they were just scrap iron, now they are starting to become increasingly collectble. Jim

gcottingham · 12-12-2012, 10:37 PM

I have one that looks a lot like that on my 69 that I just started resto on. It's welded to the frame, so it's going to be a pain to get off. Probably a common aftermarket piece for the day. It's a very thick steel bumper.
Posted via Mobile Device

Seamus · 12-12-2012, 11:43 PM

Here's a pic - will fit '55 thru '66

Moline_Puller · 12-13-2012, 10:06 AM

Thanks Guys!

The more I look around, the more I think I'm going to stick with it. It is very well built and fits very nicely..but it is not welded on...that would suck!

I'm gld to hear that there is some interest in the older aftermarket stuff. I kinda want to keep it looking like an older, well-seasoned truck!

Chris

12-10-2012, 02:26 PM	#1
Moline_Puller Registered User Join Date: Dec 2012 Location: Sussex, NJ Posts: 202	rear bumper question... Hi Guys, Every time I come on here, I am amazed at how much info is on here...I learn something new every time! This might be a dumb question, I'm not sure. After looking through a lot of pics of '67-72's, I can't remember seeing another one with a rear bumper like the one on my truck...here is a pic. Is this a GM bumper? Or did someone swap it out? I actually kinda like it, because it isn't as big as some of the step bumpers. Thanks for the help! I'm just kinda curious as to what it is and if it is correct for the truck. Chris Attached Images

12-10-2012, 02:30 PM	#2
50bomb Registered User Join Date: Jul 2010 Location: Hemet,Ca Posts: 1,502	Re: rear bumper question... I prefer the sports bumpers but I havent found one that I could paint. This is a heavy duty bumper I had on my truck but Junked the bumper a year ago. Now I have no bumper and regret junking it because I do not have a place to put my license plate. I could definatley live with a bumper like the ONE you have on your truck. Attached Images __________________ Stovebolt-It is painted

12-10-2012, 02:34 PM	#3
Moline_Puller Registered User Join Date: Dec 2012 Location: Sussex, NJ Posts: 202	Re: rear bumper question... Hey 50bomb, Yeah, I was kinda planning on putting a roll pan on it, but I kinda like this bumper...it isn't as big as a lot of the step bumpers.

12-10-2012, 02:59 PM	#4
yuccales Registered User Join Date: May 2011 Location: Northern Calif. Posts: 3,771	Re: rear bumper question... That bumper looks good, might even look good chrome!

12-10-2012, 03:24 PM	#5
truckster Senior Member Join Date: Jan 2001 Location: Orem, Utah Posts: 7,976	Re: rear bumper question... That's not a factory bumper. It's aftermarket or dealer-installed. They weren't too rare way back when, but you don't see a lot of them anymore.

12-10-2012, 03:31 PM	#6
SS Tim Registered User Join Date: Aug 2010 Location: Edwards, CA Posts: 7,503	Re: rear bumper question... From the angles of the ends and general simplicity of it I would say it was homemade. Not that is a bad thing just saying it is probably fairly unique. A picture or two of the bottom side and brackets would probably confirm this. If I were keeping this on a truck a little flattening on the ends,say an inch would keep it from hurting so much when you run into it. Also when you need something identified a picture of the part in question is more helpful than the truck as a whole. The stripes are they the factory D89 stripes? They would be on the SPID label if original. Attached Images __________________ Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID Blazer SPID Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders Do you have a 1972 Plaid Pickup? Plaid Blazer ** Plaid Suburban

12-10-2012, 03:27 PM	#7
Moline_Puller Registered User Join Date: Dec 2012 Location: Sussex, NJ Posts: 202	Re: rear bumper question... Thanks truckster! That answers my question...I didn't think it was a GM bumper. I haven't seen any other ones like it.

12-10-2012, 03:36 PM	#8
Mister-B Account Suspended Join Date: Oct 2012 Location: Salt Lake City, Utah Posts: 3,331	Re: rear bumper question... Check out my bumper restoration thread. http://67-72chevytrucks.com/vboard/s...d.php?t=551823 For less than about 20 bucks, you can get that thing looking like new Posted via Mobile Device

12-10-2012, 03:45 PM	#9
Moline_Puller Registered User Join Date: Dec 2012 Location: Sussex, NJ Posts: 202	Re: rear bumper question... Hey Mister-B, Thanks for the advice. Did you prep your bumper (sandbalst, wire brush, etc?) before your primered it?

12-10-2012, 04:48 PM	#11
Moline_Puller Registered User Join Date: Dec 2012 Location: Sussex, NJ Posts: 202	Re: rear bumper question... Thanks again. I'll have to give that primer a try

12-10-2012, 06:56 PM	#13
Seamus Registered User Join Date: Mar 2011 Location: Raeford. NC Posts: 69	Re: rear bumper question... Bumper looks after market - see similar on farm trucks. I have a similar one I took off of my '56 except it wraps around the back fenders a little. They are heavier than stock.

12-10-2012, 09:39 PM	#14
hugger6933 Registered User Join Date: Oct 2008 Location: Marianna Arkansas Posts: 7,280	Re: rear bumper question... They are aftermarket or dealer bumpers. Most dealers offered them as a courtesy to their new truck buyers back in the day. The price you had to pay for having the "free" bumper was the dealers name and town engraved and hilighted in another color in the bumper. I have some of these bumpers from the dealers from the towns around me . One of my 70's [the swb] has one. I also have two or three more on the ground at the shop. Years ago they were just scrap iron, now they are starting to become increasingly collectble. Jim

12-12-2012, 10:37 PM	#15
gcottingham Registered User Join Date: Nov 2012 Location: Indianapolis Posts: 34	Re: rear bumper question... I have one that looks a lot like that on my 69 that I just started resto on. It's welded to the frame, so it's going to be a pain to get off. Probably a common aftermarket piece for the day. It's a very thick steel bumper. Posted via Mobile Device

12-12-2012, 11:43 PM	#16
Seamus Registered User Join Date: Mar 2011 Location: Raeford. NC Posts: 69	Re: rear bumper question... Here's a pic - will fit '55 thru '66 Attached Images

12-13-2012, 10:06 AM	#17
Moline_Puller Registered User Join Date: Dec 2012 Location: Sussex, NJ Posts: 202	Re: rear bumper question... Thanks Guys! The more I look around, the more I think I'm going to stick with it. It is very well built and fits very nicely..but it is not welded on...that would suck! I'm gld to hear that there is some interest in the older aftermarket stuff. I kinda want to keep it looking like an older, well-seasoned truck! Chris



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.