Upgrade to power brakes didn't work

[LSUMurse]

I got a booster with everything from the rod to the pedal to the prop valve including all the brackets (it's off either a '67 or '71, I haven't gotten the info yet). I pulled my current master cylinder off the firewall (without disconnecting the lines) and installed the booster, bracket, and a vacuum line. I teed off the vacuum for the transmission (the one between the carb and distributor). Everything seems to be connected correctly.

The brakes barely work. The travel on the pedal is shorter, though it does not bottom out on the floorboard. I did the booster test (build up pressure and then turn the truck on and see if the pedal goes down further) and the pedal didn't move when I turned on the engine.

The booster came with a master cylinder of it's own (with equal sized reservoirs). Should I try using it in place of the stock one? Could it be an incorrect push rod between the booster and MC? I am using the one from the setup I bought. Should I just get a whole setup from Napa? The ones with the MC and booster connected.

Any help is appreciated.

[Stocker]

I'm confused -- you got a new prop. valve, and you re-used your old MC without disconnecting the lines? How is that possible? Can you post a pic or two to show your setup? Or did you just not use the prop valve? It's not needed with all drums.

Dunno what truck you have but I assume it's drum / drum. Your new MC has equal size reservoirs so it's from a '70 or older drum / drum. If it was from a '71 it would be for front discs.

[LockDoc]

Originally Posted by Stocker

I'm confused -- you got a new prop. valve, and you re-used your old MC without disconnecting the lines? How is that possible? Can you post a pic or two to show your setup? Or did you just not use the prop valve? It's not needed with all drums.

Dunno what truck you have but I assume it's drum / drum. Your new MC has equal size reservoirs so it's from a '70 or older drum / drum. If it was from a '71 it would be for front discs.

I upgraded my '67 drum/drum setup to power without unhooking the lines. There was enough slack in the lines to move it back and bolt it to the booster with no problem. He doesn't say he replaced the prop valve, the new setup just came with one.

LSUMurse: Your vacuum line needs to come from the intake manifold. There should be a fitting or plug in the intake manifold just behind the carb. You need to plumb it to that...

LockDoc

[LSUMurse]

Originally Posted by LockDoc

I upgraded my '67 drum/drum setup to power without unhooking the lines. There was enough slack in the lines to move it back and bolt it to the booster with no problem. He doesn't say he replaced the prop valve, the new setup just came with one.

LSUMurse: Your vacuum line needs to come from the intake manifold. There should be a fitting or plug in the intake manifold just behind the carb. You need to plumb it to that...

LockDoc

I have a vacuum line. There was a fitting with a single line coming off the intake that I believe goes down to the transmission. I turned that into a tee and used it for the vacuum. When I pull the vacuum line out of the booster, it seems to have a pretty good amount of vacuum. Also, it runs rough now. I'm thinking the booster may be shot.
It won't let me upload a pic from my phone, but there is definitely a vacuum line.
Posted via Mobile Device

[LockDoc]

Originally Posted by LSUMurse

I have a vacuum line. There was a fitting with a single line coming off the intake that I believe goes down to the transmission. I turned that into a tee and used it for the vacuum. When I pull the vacuum line out of the booster, it seems to have a pretty good amount of vacuum. Also, it runs rough now. I'm thinking the booster may be shot.
It won't let me upload a pic from my phone, but there is definitely a vacuum line.
Posted via Mobile Device

Yes, if the booster diaphragm has a hole in it that could cause the symptoms you are experiencing.

LockDoc

[LSUMurse]

Do you think it's safer to buy the whole setup (master cylinder and booster together)? I've read on some threads that not all MC's and boosters use the same pushrods.
Posted via Mobile Device

[PanelDeland]

Sounds like you have too little volume on the vacuum line.It shoud be a 3/8 IIRC.The rod is also slightly different.Longer I think for PB.Yours may be enough because it's a very minor difference.

[jocko]

I believe your issue is a non-power master cylinder mated to a power booster, i.e. incorrect inter-booster/mc pushrod.

Generally, manual brake master cylinders have the deep bore pistons while power brake master cylinders have the shallow bore pistons. So, although you have power assist, the powered pushrod in the booster isn't engaging the bottom of the master cylinder bore.

You asked whether you should buy the master+booster together? Yes, that will elminate this problem because it will come as a matched set - power mc mated to booster with correct intermediate pushrod. Could you fiddle around all day and try to cobble together a homemade intermediate pushrod? Yes. But I wouldn't. I'd go buy the correct master that would have been mated to the booster that you bought if you had bought them as a set and install it. Sucks you will have to bleed some stuff, but, gotta be done.

I put a 67 dual res master on a 66 a while back - kept everything manual in the swap. Then, when I later opted to upgrade to power brakes, I learned the error of my ways... So, my lesson learned was to always buy a master cylinder WITH the booster when I am upgrading from manual to power brakes.

Hope that helps. Others have touched on the issue above and I believe that is the overall problem - your intermediate pushrod is not engaging the bottom of the master cylinder piston bore becuase you still have what was originally a manual brake master cylinder, and thus the "deep" bore piston. Easiest solution is to get the correct MC.

Personally, I don't like to cobble things together when it comes to my brakes - and when you consider the master cylinder is probably $20 at Oreily or something like that, why monkey with a homemade intermediate pushrod? Boosters weren't designed to work with deep bore mc pistons, but of course it could be done. Best $20 you'll ever spend though - my 2 cents only.

[LSUMurse]

Thank you both for your replies. I will go from here. I am inclined to attempt to make my own push rod. It's not that I mind bleeding the brakes, it's more a money issue. I hate fiddling with safety equipment, though.

I have decided that this truck is VERY resistant to change. I was calling her Rosie (after the AC/DC song "Whole Lotta Rosie"), but I may switch to Christine. She's certainly going to kill me!!

[jocko]

the whole enchilada: http://www.oreillyauto.com/site/c/de...1305&ppt=C0066

just the mc:
Oreilly lists three, only one specifies "manual or power" which means they don't know what they are talking about (pic of the middle one with this wording looks like deep bore - and wouldn't work) - really have to follow "buyer beware" (i.e. know what you need and ignore the parts counter gal).
http://www.oreillyauto.com/site/c/se...make=Chevrolet



Easiest route: return your Booster - and buy the combo (1st link), that way you know you're good to go. I understand $ are an issue, but doing this would only be sinking about $20 more into the project.

[SS Tim]

Really think the travel is a matter of incorrect pushrod length. Since the factory sold booster kits for dealer installation (C10 P/N 987446) it would seem that this is a simple swap given the right parts. Unfortunately I don't have a kit breakdown, but given the dealer price of $28.60 plus a 1.0 flat rate for installation vs $45 for the factory J70 option I'd say it was a dry swap kit (booster&pushrod only).

But even with the correct installation if the booster is used and unknown ("it's off either a '67 or '71, I haven't gotten the info yet")that may very well be the root problem. Have you tried pulling a vacuum on the booster with a vacuum pump or even another engine to verify it does not leak.

Last thing is the vacuum source, a transmission modulator line is generally a lot smaller than a brake booster vacuum port. Have you reviewed the factory service manual on the brake and vacuum systems?

[hyatt]

Your vacumn line needs to be at least 5/16 to provide enough vacume to power the boosted I always use 3/8 line

[chipflyer]

LSUMurse, take a look at this old link http://67-72chevytrucks.com/vboard/s...d.php?t=214559
If you start at post # 6, look at the pictures, AND read the descriptions I think you will find the info you are after.
Hope it helps

Jeff

[LSUMurse]

Chipflyer: I read that, thanks though. The setup I bought was complete from the pedal rod to the prop valve. I assumed it was a matching set, but it's looking like it wasn't. I do appreciate the heads up though. I have a lot to learn about these trucks.
Posted via Mobile Device

[68gmsee]

The manual master cylinder will work with the power booster. I used my original one with the booster for about 15 years on my 68 with manual drum/drum. But, the push rod has to be the correct length. Pull the one you have off the booster to look at how it's made. If it's like mine you'll need access to a machine shop to do it. Just depends on which booster you have.

[kevmic28]

I had the same problem when I did mine. I think I may see your problem. There should be a rubber gasket that fits on the end of the master cylinder between the master and the booster. With the engine running can you hear a vacuum leak from the booster?

[First c10]

I installed the mc from a 72. Even though my truck is still a drum/drum truck. But soon I will be upgrading to front discs. I picked up the the complete setup from oriellys. 103$. All I had to do was drill a hole 1" lower then the stock Manual mc. The hardest part was lowering the column to install the bolt that attaches the rod to the peddle.
Posted via Mobile Device

[LSUMurse]

It was the stinking (if I didn't have respect for the site that would be a different word) BOOSTER! Brakes work like a champ!

I knew she was trying to tell me something by running rough.
Posted via Mobile Device
Posted via Mobile Device

[jocko]

glad got it resolved! Frustrating when new parts are not working, those are the ones you expect to be good!

[SS Tim]

Were they new or used parts? The impression I have is they were used.

[LSUMurse]

They were used. I bought the whole setup together in an attempt to make it easier. That proved to be incorrect.

It's ok, though. I now know a lot more about how the upper half of the brakes are setup. I don't mind fighting her, as long as I get my way in the end.
Posted via Mobile Device

[Jayschevy]

I bought a complete kit (MC and booster) from Brothers awhile back. Just put them on this weekend and it still feels like I have manual brakes. Could the booster they sent me be bad?

[LSUMurse]

Anything you buy new has the possibility of failing. Are you generating enough vacuum? Did you bench bleed the MC before installing?

[Jayschevy]

Originally Posted by LSUMurse

Anything you buy new has the possibility of failing. Are you generating enough vacuum? Did you bench bleed the MC before installing?

Yes and Yes. It maybe the booster. I may give brothers a call tomorrow.

[LSUMurse]

It seems to me that if you have vacuum to the booster and everything is bled properly, it should work. There is a world of difference in the feeling of my brakes, now that I figured out the problem. With buying the MC and booster together, I can't imagine it would be the booster push rod. I guess you gotta call them. Good luck. Lemme know how it turns out.
Posted via Mobile Device