|
|
|
02-27-2013, 02:34 PM
|
#1 |
|
Registered User
Join Date: Sep 2011
Location: McAlester Olahoma
Posts: 114
|
axle??
ok (c10 5 lug)( k10 6 lug) after that is there any other differnts.Thanks
|
|
|
|
02-28-2013, 01:27 AM
|
#2 |
|
Registered User
Join Date: Jan 2009
Location: Louisville,Ky
Posts: 5,811
|
Re: axle??
c10 is 2wd k10 is a 4x4.
|
|
|
|
|
02-28-2013, 01:45 AM
|
#3 |
|
Senior Member
 
Join Date: Jun 2010
Location: Illinois
Posts: 2,957
|
Re: axle??
What is the reason for your question. That might be able to clear things up a little. Are you looking to switch rear ends or something?
__________________
Roy 85 Short Bed Silverado- Work in progress. http://67-72chevytrucks.com/vboard/s...d.php?t=564818 1987 R10 shortie |
|
|
|
|
02-28-2013, 10:17 AM
|
#4 |
|
Registered User
Join Date: Sep 2011
Location: McAlester Olahoma
Posts: 114
|
Re: axle??
ok yes I am looking at a swap.I have 1968 2 wheel drive that is making alot of noise.
POL make kit to put the 1973-87 rear end into the 1968.My 68 has 6 lugs and I was look for a better gearing 3.73 is way to many RPMs.And There is only two gears for the 6 lug that wouls be a bolt in.3.73 or 3.08.The 3.42 with the tire size that I have would work for the overdrive trans that I am going to put in.Thanks |
|
|
|
|
02-28-2013, 02:13 PM
|
#5 |
|
Registered User
Join Date: May 2009
Location: Motor City
Posts: 9,230
|
Re: axle??
Assuming the overdrive you are going to is in the .70 to .73 range, and assuming a "normal" sized tire (P235/75R-15 or so) I would recommend the 3.73 axle ratio.
I would guess the 3.42 is not enough axle with the overdrive (unless you are using a teeny tire). K
__________________
Chevrolet Flint Assembly 1979-1986 GM Full Size Truck Engineering 1986 - 2019 Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926 My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524 Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/ |
|
|
|
|
02-28-2013, 02:14 PM
|
#6 | |
|
Registered User
Join Date: May 2009
Location: Motor City
Posts: 9,230
|
Re: axle??
Quote:
K
__________________
Chevrolet Flint Assembly 1979-1986 GM Full Size Truck Engineering 1986 - 2019 Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926 My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524 Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/ |
|
|
|
|
|
02-28-2013, 03:59 PM
|
#7 |
|
Registered User
Join Date: Sep 2011
Location: McAlester Olahoma
Posts: 114
|
Re: axle??
Knowbody that I would trust around here.Rear has a lot of play in it and it growls.After I posted this I found a Calculator Looks like the 3.73s would be better.
|
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
