Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
07-28-2013, 06:58 PM | #1 |
Registered User
Join Date: May 2013
Location: Middle River, Md.
Posts: 28
|
drive shaft for a shortbed 350 turbo
Hey all..... Well..getting very close on putting my 2004r in my truck.. I did a complet check<cleaned & painted it.. Putting the lockup switch this week into the trans and have everything for the trans..."except" im gonna need a drive shaft for a 350trans.. I know the yoke is the same as the 2004r as for the 350turbo.... Now, the 400 trans i have is longer then the 350/2004r.
Any ideas on the length of the standard 350 driveshaft is???? I read its 59.5" long....Is this correct. And im sure all short beds from'73-87 will work. Any suggestions...would be much appreciate it.. Cause there's a truchshow in Carlisle,Pa. on August 1-4th..gonna try there..but will call the junk yards before then. Thanks!! mikekaye69 is online now Report Post |
07-29-2013, 09:06 AM | #2 |
Special Order
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
Re: drive shaft for a shortbed 350 turbo
This is a pickup...2wd/4wd? You had a TH400 and now a 200r4? If it's in the truck,just put your old driveshaft in and measure how much more you need. You'll probably have better luck on the pickup message board
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
07-29-2013, 05:32 PM | #3 |
Registered User
Join Date: May 2013
Location: Middle River, Md.
Posts: 28
|
Re: drive shaft for a '87 2wd. shortbed 350 turbo
Hey all..... Well..getting very close on putting my 2004r in my truck.. I did a complet check<cleaned & painted it.. Putting the lockup switch this week into the trans and have everything for the trans..."except" im gonna need a drive shaft for a 350trans.. I know the yoke is the same as the 2004r as for the 350turbo.... Now, the 400 trans i have is longer then the 350/2004r.
I have messured the shaft that its there rite now with the th400. from rear-universal joint to the front universal joint is just over 54". Any ideas on the length of the standard 350 driveshaft is???? I read its 59.5" long....Is this correct. And im sure all short beds from'73-87 will work. Any suggestions...would be much appreciate it.. Cause there's a truchshow in Carlisle,Pa. on August 1-4th..gonna try there..but will call the junk yards before then. Thanks!! |
07-29-2013, 08:53 PM | #4 |
Registered User
Join Date: Apr 2013
Location: Laporte, IN
Posts: 57
|
Re: drive shaft for a shortbed 350 turbo
measure and cut a driveshaft down, have it balanced by a shop... gtg and a TON cheaper
|
07-29-2013, 09:43 PM | #5 |
Registered User
Join Date: Dec 2012
Location: Preble county ohio
Posts: 1,914
|
Re: drive shaft for a shortbed 350 turbo
measure the one you have, if you dont have one get a tape measure and a buddy!
__________________
"DON'T TOUCH THE TRIM!!"-Early Kyler |
Bookmarks |
|
|