Aminum intakes for sale - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**crossy** · 07-03-2003, 03:55 AM

ALL manifolds listed are Aluminum and used . All are Dual plane design, I do not sell junk. Even if I heli-coil something I guarantee that it is done right . I can take a GOOD pic of any of these..all small block ones are for PRE-1987 heads. Prices DO NOT include shipping. the small block intakes weigh about 20 Lbs. properly boxed and I am in N.J. @ 08070 zip. I can figure shipping with your zip code. I accept paypal if you add 3% to price. Also accept money orders. PLEASE EMAIL ME PERSONALLY at all4trux@snip.net and be specific in the subject box. thanx, DAVE

1.)= $140 ,SBC, Edelbrock Performer #2101 , Finish is Jethot coated inside & out. on a 1-10 scale the jethot is still an 8, very clean , No pitting, If it gets tarnished looking it shines back up with 'neverdull '. Jethot is impervious to antifreeze corrosion attack. this manifold will look good for a long time. I want less than it cost just to get it coated.
2.)=$69, SBC, Holley Contender #300-38, Finish is sandblasted clean,clear coated.comparable to Edelbrock performer, I think this is better for trucks with stock engine. has ridges in floor to break up fuel puddling. No pitting from corrosion. heater hose nipple included.

3.)= SOLD.

4.)= $99,SBC, Edelbrock Performer EGR #3701 ,Finish is bead blasted and clear coated, new condition. this is for the guys that want an aftermarket manifold but have state laws to contend with. There is a block off plate on the EGR hole now, so you can use it that way until you need to pass inspection. hose nipple installed.

5.)=$99,SBC, ZZ4 GM bowtie #10185063 EGR ,about equal to a performer RPM in design but has EGR hole. ,Finish is factory and then was wire wheeled for a little shine. I can sandblast it for $10 extra. , new condition. this is for the guys that want a performence aftermarket manifold but have state laws to contend with. There is a block off plate on the EGR hole now, so you can use it that way until you need to pass inspection.

6.)=$79,SBC,Weiand Stealth #8016, Finish is bead blasted then clear coated. Holley square flange, This manifold is equal to a Performer RPM, No pitting.

7.)=SOLD$.

8.)=$99 , SBC, Edelbrock C4B , finish is clean but sprayed with Aluminum paint ??. I can sandblast this for $10 extra. This old school manifold has the provision for oil tube hole in the front for older engines. This was pretty much Edelbrocks original Mid to upper rpm street manifold that is designed like the old original Z28 intake.Has Holley square flange bolt pattern. very minor pitting,great shape for a 30 year old intake.These were great then and still are now.

9.)=$115 , Big Block Chevy BBC, Edelbrock performer 2-0 for oval port heads. Finish is bead blasted and clear coated. looks better than new.No pitting,

sweet n rare67 · 07-03-2003, 03:16 PM

Can you post a pic of #3?

70 CST 4X4 · 07-03-2003, 04:44 PM

too bad! Just picked up an intakeand put it on. wish I would have seen this a couple of weeks ago.

**crossy** · 07-03-2003, 05:41 PM

because i am on my way into work i will post this pic here,but for any others please email me at home and I will send pics, DAVE

**crossy** · 07-10-2003, 11:32 AM

#3 has been sold. DAVE

ZOOMY · 07-11-2003, 02:07 AM

Are 2 & 7 for square or spread-bore carbs ?.....Thanks......Zoomy

**crossy** · 07-11-2003, 06:08 AM

#6 & #8 are the only square flange.

ZOOMY · 07-21-2003, 06:14 AM

Is #6 still available ?

**crossy** · 07-21-2003, 07:46 AM

yup.

**crossy** · 07-21-2003, 07:55 AM

top left =#4 , block off plate is not installed in the pic and it has a square flange adapter installed in this pic. but it is #4.

bottom left= #7SOLD!

top right= #5

bottom right=#6

ZOOMY · 07-22-2003, 01:38 AM

.

ZOOMY · 07-22-2003, 07:19 AM

You have e-mail

**crossy** · 08-05-2003, 10:37 PM

#3 & #& are Sold thanx ZOOMY. DAVE

07-21-2003, 07:46 AM	#9
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	yup. __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.

07-22-2003, 01:38 AM	#11
ZOOMY Senior Member Join Date: Feb 2003 Location: WIS Posts: 1,752	ttt .

07-22-2003, 07:19 AM	#12
ZOOMY Senior Member Join Date: Feb 2003 Location: WIS Posts: 1,752	intakes You have e-mail

08-05-2003, 10:37 PM	#13
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	#3 & #& are Sold thanx ZOOMY. DAVE __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.

07-03-2003, 03:55 AM	#1
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	Aluminum intakes for sale ALL manifolds listed are Aluminum and used . All are Dual plane design, I do not sell junk. Even if I heli-coil something I guarantee that it is done right . I can take a GOOD pic of any of these..all small block ones are for PRE-1987 heads. Prices DO NOT include shipping. the small block intakes weigh about 20 Lbs. properly boxed and I am in N.J. @ 08070 zip. I can figure shipping with your zip code. I accept paypal if you add 3% to price. Also accept money orders. PLEASE EMAIL ME PERSONALLY at all4trux@snip.net and be specific in the subject box. thanx, DAVE 1.)= $140 ,SBC, Edelbrock Performer #2101 , Finish is Jethot coated inside & out. on a 1-10 scale the jethot is still an 8, very clean , No pitting, If it gets tarnished looking it shines back up with 'neverdull '. Jethot is impervious to antifreeze corrosion attack. this manifold will look good for a long time. I want less than it cost just to get it coated. 2.)=$69, SBC, Holley Contender #300-38, Finish is sandblasted clean,clear coated.comparable to Edelbrock performer, I think this is better for trucks with stock engine. has ridges in floor to break up fuel puddling. No pitting from corrosion. heater hose nipple included. 3.)= SOLD. 4.)= $99,SBC, Edelbrock Performer EGR #3701 ,Finish is bead blasted and clear coated, new condition. this is for the guys that want an aftermarket manifold but have state laws to contend with. There is a block off plate on the EGR hole now, so you can use it that way until you need to pass inspection. hose nipple installed. 5.)=$99,SBC, ZZ4 GM bowtie #10185063 EGR ,about equal to a performer RPM in design but has EGR hole. ,Finish is factory and then was wire wheeled for a little shine. I can sandblast it for $10 extra. , new condition. this is for the guys that want a performence aftermarket manifold but have state laws to contend with. There is a block off plate on the EGR hole now, so you can use it that way until you need to pass inspection. 6.)=$79,SBC,Weiand Stealth #8016, Finish is bead blasted then clear coated. Holley square flange, This manifold is equal to a Performer RPM, No pitting. 7.)=SOLD$. 8.)=$99 , SBC, Edelbrock C4B , finish is clean but sprayed with Aluminum paint ??. I can sandblast this for $10 extra. This old school manifold has the provision for oil tube hole in the front for older engines. This was pretty much Edelbrocks original Mid to upper rpm street manifold that is designed like the old original Z28 intake.Has Holley square flange bolt pattern. very minor pitting,great shape for a 30 year old intake.These were great then and still are now. 9.)=$115 , Big Block Chevy BBC, Edelbrock performer 2-0 for oval port heads. Finish is bead blasted and clear coated. looks better than new.No pitting, __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks. Last edited by crossy; 08-05-2003 at 10:35 PM.

07-03-2003, 03:16 PM	#2
sweet n rare67 Young truck fanatic Join Date: Jun 2003 Location: The wonderful Mat-Su Valley....Palmer, Ak Posts: 253	Can you post a pic of #3?

07-03-2003, 04:44 PM	#3
70 CST 4X4 Have A Nice Day! Join Date: May 2003 Location: California Posts: 355	too bad! Just picked up an intakeand put it on. wish I would have seen this a couple of weeks ago. __________________ 1970 CST K10 350/350/205 Short Bed - Fleetside Tach-Tilt-A/C-Tow Hooks Front & Rear Disc Brakes Front & Rear Posi 3.73 Gears 30 Gallon Stainless Fuel Tank SOLD 01/18 !!!!! 2007 2500 HD Classic Crew Cab LT2 4X4 Duramax LBZ

07-03-2003, 05:41 PM	#4
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	because i am on my way into work i will post this pic here,but for any others please email me at home and I will send pics, DAVE __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.

07-10-2003, 11:32 AM	#5
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	#3 has been sold. DAVE __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.

07-11-2003, 02:07 AM	#6
ZOOMY Senior Member Join Date: Feb 2003 Location: WIS Posts: 1,752	#2 & #7 Are 2 & 7 for square or spread-bore carbs ?.....Thanks......Zoomy

07-11-2003, 06:08 AM	#7
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	#6 & #8 are the only square flange. __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.

07-21-2003, 06:14 AM	#8
ZOOMY Senior Member Join Date: Feb 2003 Location: WIS Posts: 1,752	#6 Is #6 still available ?

07-21-2003, 07:55 AM	#10
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	top left =#4 , block off plate is not installed in the pic and it has a square flange adapter installed in this pic. but it is #4. bottom left= #7SOLD! top right= #5 bottom right=#6 __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks. Last edited by crossy; 08-05-2003 at 10:36 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.