CA 81-87 Front Sheetmetal for sale

[RPOZ11]

81-87 Front Sheetmetal for sale

$300.00 OBO
Make me an offer

This is a front end from an 81-87 that I am taking off of my 1975 Chevy Truck.
Here is what I have :
Hood, with interior latch + cable
Hood lift brackets and rubber seals to cowl
Hood lift brackets at fender, shown
Cowl vent panel
L and R front fenders
L and R inner fenders
Grill
SS trim as shown
Front Bumper + brackets ( not sure if the brackets are the correct ones but I 'think' that they are )
Core Support
SBC fan shroud and mounting bracket
Radiator
Misc attatched items on core support and fenders

I would like to sell the whole thing as 1 sale.
If this ends up unsold as 1, then I will take offers per part.

This is all located in SoCal.

LOCAL SALE PREFERRED

I could deliver or meet half way depending upon the distance.
You pay my fuel both ways.
THX

[RPOZ11]

hood

[RPOZ11]

fenders

[RPOZ11]

Engine side
Inner fenders
core support
etc etc

[sc85k-10]

Do you have all the fender bolts still

[RPOZ11]

I should.
What group do you need?

[sc85k-10]

In need of mostly inner fender bolts but ill take whatever

[RPOZ11]

Originally Posted by sc85k-10

In need of mostly inner fender bolts but ill take whatever

Ill get you what I can.
I just took the front end off.
Most of the inner fender well bolts are used throughout the front group so getting you enough should be easy.
Just bear with me.
Been super busy and limited time...

[RPOZ11]

ttt

Anyone want this stuff?
Its all going to the metal scrap yard otherwise...

More pics...
sbc Radiator , fan shroud, and top plate

[RPOZ11]

more pics...

Misc front group parts

[RPOZ11]

Headlights with buckets
These are singles that are hi & low beams

Turn signal housings

[sc85k-10]

No prob man if I was closer I'd take the core support and inner fenders but im in south carolina

[RPOZ11]

I removed alot of bolts from this and from 4 core supports I had for parts.
You need all of the inner fender well to fenders correct?
Did you want the slip on fasteners that go onto the fenders that receive the bolts?
I have some, maybe all but might not be as good as new ones.
The correct bolts to the cab I wont have.
Did you need enough to assmble the front of the fenders to the core support?
What year truck are you putting this all on?
I ask as the later years I think dont take as many.
on the 73-80 front ends, they have extra mounting positions and brackets to install the front lower pan below the grill.

[RPOZ11]

As for the front sheetmetal, I have only 1 person call on all of this.

Left front fender might be sold, otherwise it all goes to scrap on 10-28-2013

[ScottH]

How many rows is the radiator?
Might be interested in radiator, shroud, and top plate.

Scott

[RPOZ11]

Originally Posted by ScottH

How many rows is the radiator?
Might be interested in radiator, shroud, and top plate.

Scott

I believe that the its a 3 row.
If you wanted it I can have it cleaned out out pressure tested for immediate use.
That would be a standard radiator whether its an automatic or a manual transmission.
I think that I have 2 sets of these left.
2 upper mounts, 2 fan shrouds remaining.
I have not tossed these for scrap yet.

[sc85k-10]

1986

[RPOZ11]

Originally Posted by sc85k-10

1986

I dont think that you need the extra bolts etc.
I will count them out for you.
I have an extra pair of fenders in storage that have some of the correct fender receiving slide in nut pieces.

I will get this all for you.
Thanx for being patient.
I do work alot.

[ScottH]

thanks but wanted to know how many cooling rows the rad is

[ScottH]

Thanks for the info. Turns out I wont be getting the truck after all so gonna pass on the parts.

Scott

[RPOZ11]

Sheet metal gone.

Radiators, upper plates, and shrouds remain.