WI Wtb 1967 chevy truck hood need template - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**60-66** · 01-04-2014, 07:50 PM

Im looking for a junk 1967 hood if someone is willing to cut the front skin off so I can use as a template for drilling the holes for the C H E V R O L E T letters in the front. My hood was replaced with an NOS hood with no holes drilled. Let me know what you might have. Thanks !!

**Elliot949** · 01-04-2014, 09:17 PM

I may be able to make you a template... I will look at that tomorrow for you...

**Elliot949** · 01-10-2014, 07:57 AM

I will go to the body shop (that is where my truck is) in the next day or so and do this for you...

**60-66** · 01-10-2014, 09:28 AM

Thank you, I really appreciate this !! Jon

ecgate · 01-12-2014, 09:42 PM

I would be interested in one of those templates also if your willing to make two of them. Let me know. Thanks.

**Elliot949** · 01-12-2014, 09:45 PM

sure... no problem...

**60-66** · 01-14-2014, 10:10 AM

Bump

**richard2717** · 01-14-2014, 08:49 PM

Are you still looking for a template? I was out in the shop tonight and remembered you were looking for one so I pulled out the paper, tape, marker and camera. My hood is a 68' but it should all be the same. PM me your address if still needed & I will send it out tomorrow after I make a few duplicates

Richard

**Elliot949** · 01-14-2014, 11:06 PM

Hey Richard... Thanks... I was going to the body shop tomorrow to do that but if you have it handled then cool...

**richard2717** · 01-15-2014, 08:44 AM

Here are pictures of what I did last night but I can mail the paper patterns as well. Not shown in the picture ( since I forgot to take final picture) is the cross marks (center marks) for each hole and the measurements and where I measured from, written on the pattern.

**60-66** · 01-15-2014, 02:12 PM

PM Sent. Thank you !

**richard2717** · 01-20-2014, 08:58 PM

UPS email says they delivered the pattern today. Hope it helps

Richard

**60-66** · 01-21-2014, 12:16 AM

Richard, YES Thank you VERY Much.Your template turned out nice. Now if I can just get the $alls to drill the hood

. I think I will mask it all off and mark accordingly then measure measure measure.

**richard2717** · 01-21-2014, 08:14 AM

I think I wrote it on the pattern but I measured the big holes at 5/32" and the small holes at 3/32". If you need any other measurements just let me know but I think the way I laid it out you should be good.

One thing though. I assume the back side of your hood has the access holes to be able to tighten down the speed nuts on the letters? IF not let me know & I will see if I can get a pattern of that. IT never crossed my mind until last night.

Richard

01-04-2014, 07:50 PM	#1
60-66 Registered User Join Date: Apr 2012 Location: Wisconsin Posts: 3,329	Wtb 1967 chevy truck hood need template Im looking for a junk 1967 hood if someone is willing to cut the front skin off so I can use as a template for drilling the holes for the C H E V R O L E T letters in the front. My hood was replaced with an NOS hood with no holes drilled. Let me know what you might have. Thanks !! __________________ IS IT an EATON or Chevrolet rear axle https://67-72chevytrucks.com/vboard/...d.php?t=843778 The hubcap thread http://67-72chevytrucks.com/vboard/s...d.php?t=702839 WANTED : 1963-1966 6 Cylinder Fan Shroud WANTED :1964-1966 PANEL TRUCK

01-04-2014, 09:17 PM	#2
Elliot949 Registered User Join Date: Sep 2010 Location: Winfield, Ks. Posts: 4,162	Re: Wtb 1967 chevy truck hood need template I may be able to make you a template... I will look at that tomorrow for you...

01-10-2014, 07:57 AM	#3
Elliot949 Registered User Join Date: Sep 2010 Location: Winfield, Ks. Posts: 4,162	Re: Wtb 1967 chevy truck hood need template I will go to the body shop (that is where my truck is) in the next day or so and do this for you...

01-10-2014, 09:28 AM	#4
60-66 Registered User Join Date: Apr 2012 Location: Wisconsin Posts: 3,329	Re: Wtb 1967 chevy truck hood need template Thank you, I really appreciate this !! Jon __________________ IS IT an EATON or Chevrolet rear axle https://67-72chevytrucks.com/vboard/...d.php?t=843778 The hubcap thread http://67-72chevytrucks.com/vboard/s...d.php?t=702839 WANTED : 1963-1966 6 Cylinder Fan Shroud WANTED :1964-1966 PANEL TRUCK

01-12-2014, 09:42 PM	#5
ecgate Registered User Join Date: Aug 2012 Location: Council Bluffs, Iowa Posts: 280	Re: Wtb 1967 chevy truck hood need template I would be interested in one of those templates also if your willing to make two of them. Let me know. Thanks.

01-12-2014, 09:45 PM	#6
Elliot949 Registered User Join Date: Sep 2010 Location: Winfield, Ks. Posts: 4,162	Re: Wtb 1967 chevy truck hood need template sure... no problem...

01-14-2014, 10:10 AM	#7
60-66 Registered User Join Date: Apr 2012 Location: Wisconsin Posts: 3,329	Re: Wtb 1967 chevy truck hood need template Bump __________________ IS IT an EATON or Chevrolet rear axle https://67-72chevytrucks.com/vboard/...d.php?t=843778 The hubcap thread http://67-72chevytrucks.com/vboard/s...d.php?t=702839 WANTED : 1963-1966 6 Cylinder Fan Shroud WANTED :1964-1966 PANEL TRUCK

01-14-2014, 08:49 PM	#8
richard2717 Equal opportunity joke ofender Join Date: Oct 2011 Location: Eastern Shore of MD Posts: 10,091	Re: Wtb 1967 chevy truck hood need template Are you still looking for a template? I was out in the shop tonight and remembered you were looking for one so I pulled out the paper, tape, marker and camera. My hood is a 68' but it should all be the same. PM me your address if still needed & I will send it out tomorrow after I make a few duplicates Richard __________________ Members I have met. Dually Jams, OlBlue60, ScottH, Tommyboy24, Dujobo, Warbucket, 2003 Silverado, Notsolo, my90k5, 6t727t2, Special-K ,Jack_71C10, tabarcus,72blazer_mud_bogger,pwdcougar,RSavage,EricSean,1Rippen6,invicta455,tennaragtop71,arks, Kendal,Bennett68C10, Perpendicular, Chainsawman, McGeesCustomMinis,ShortbedClayton,longblue72,6768chevylover,Tim71,Travisarmenta,Ol' Drippy,fleetmitch,georgieb51,Dave,bcnya2,Dadsburb https://paypal.me/6772GMtruckparts Most women like the strong, silent type… Fortunately for me, my wife prefers the out-of-shape, mouthy type.

01-14-2014, 11:06 PM	#9
Elliot949 Registered User Join Date: Sep 2010 Location: Winfield, Ks. Posts: 4,162	Re: Wtb 1967 chevy truck hood need template Hey Richard... Thanks... I was going to the body shop tomorrow to do that but if you have it handled then cool...

01-15-2014, 08:44 AM	#10
richard2717 Equal opportunity joke ofender Join Date: Oct 2011 Location: Eastern Shore of MD Posts: 10,091	Re: Wtb 1967 chevy truck hood need template Here are pictures of what I did last night but I can mail the paper patterns as well. Not shown in the picture ( since I forgot to take final picture) is the cross marks (center marks) for each hole and the measurements and where I measured from, written on the pattern. Attached Images __________________ Members I have met. Dually Jams, OlBlue60, ScottH, Tommyboy24, Dujobo, Warbucket, 2003 Silverado, Notsolo, my90k5, 6t727t2, Special-K ,Jack_71C10, tabarcus,72blazer_mud_bogger,pwdcougar,RSavage,EricSean,1Rippen6,invicta455,tennaragtop71,arks, Kendal,Bennett68C10, Perpendicular, Chainsawman, McGeesCustomMinis,ShortbedClayton,longblue72,6768chevylover,Tim71,Travisarmenta,Ol' Drippy,fleetmitch,georgieb51,Dave,bcnya2,Dadsburb https://paypal.me/6772GMtruckparts Most women like the strong, silent type… Fortunately for me, my wife prefers the out-of-shape, mouthy type.

01-15-2014, 02:12 PM	#11
60-66 Registered User Join Date: Apr 2012 Location: Wisconsin Posts: 3,329	Re: Wtb 1967 chevy truck hood need template PM Sent. Thank you ! __________________ IS IT an EATON or Chevrolet rear axle https://67-72chevytrucks.com/vboard/...d.php?t=843778 The hubcap thread http://67-72chevytrucks.com/vboard/s...d.php?t=702839 WANTED : 1963-1966 6 Cylinder Fan Shroud WANTED :1964-1966 PANEL TRUCK

01-20-2014, 08:58 PM	#12
richard2717 Equal opportunity joke ofender Join Date: Oct 2011 Location: Eastern Shore of MD Posts: 10,091	Re: Wtb 1967 chevy truck hood need template UPS email says they delivered the pattern today. Hope it helps Richard __________________ Members I have met. Dually Jams, OlBlue60, ScottH, Tommyboy24, Dujobo, Warbucket, 2003 Silverado, Notsolo, my90k5, 6t727t2, Special-K ,Jack_71C10, tabarcus,72blazer_mud_bogger,pwdcougar,RSavage,EricSean,1Rippen6,invicta455,tennaragtop71,arks, Kendal,Bennett68C10, Perpendicular, Chainsawman, McGeesCustomMinis,ShortbedClayton,longblue72,6768chevylover,Tim71,Travisarmenta,Ol' Drippy,fleetmitch,georgieb51,Dave,bcnya2,Dadsburb https://paypal.me/6772GMtruckparts Most women like the strong, silent type… Fortunately for me, my wife prefers the out-of-shape, mouthy type.

01-21-2014, 12:16 AM	#13
60-66 Registered User Join Date: Apr 2012 Location: Wisconsin Posts: 3,329	Re: Wtb 1967 chevy truck hood need template Richard, YES Thank you VERY Much.Your template turned out nice. Now if I can just get the $alls to drill the hood . I think I will mask it all off and mark accordingly then measure measure measure. __________________ IS IT an EATON or Chevrolet rear axle https://67-72chevytrucks.com/vboard/...d.php?t=843778 The hubcap thread http://67-72chevytrucks.com/vboard/s...d.php?t=702839 WANTED : 1963-1966 6 Cylinder Fan Shroud WANTED :1964-1966 PANEL TRUCK

01-21-2014, 08:14 AM	#14
richard2717 Equal opportunity joke ofender Join Date: Oct 2011 Location: Eastern Shore of MD Posts: 10,091	Re: Wtb 1967 chevy truck hood need template I think I wrote it on the pattern but I measured the big holes at 5/32" and the small holes at 3/32". If you need any other measurements just let me know but I think the way I laid it out you should be good. One thing though. I assume the back side of your hood has the access holes to be able to tighten down the speed nuts on the letters? IF not let me know & I will see if I can get a pattern of that. IT never crossed my mind until last night. Richard __________________ Members I have met. Dually Jams, OlBlue60, ScottH, Tommyboy24, Dujobo, Warbucket, 2003 Silverado, Notsolo, my90k5, 6t727t2, Special-K ,Jack_71C10, tabarcus,72blazer_mud_bogger,pwdcougar,RSavage,EricSean,1Rippen6,invicta455,tennaragtop71,arks, Kendal,Bennett68C10, Perpendicular, Chainsawman, McGeesCustomMinis,ShortbedClayton,longblue72,6768chevylover,Tim71,Travisarmenta,Ol' Drippy,fleetmitch,georgieb51,Dave,bcnya2,Dadsburb https://paypal.me/6772GMtruckparts Most women like the strong, silent type… Fortunately for me, my wife prefers the out-of-shape, mouthy type.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.