OR Parting out 72 GMC K20 4x4 350-TH350

[tll74]

I just finished parting this one out. A 72 GMC 3/4t 4x4. Most all metal parts have been hot tanked and acid dipped. Media blasting available at no cost on most parts. All prices are plus shipping. Thanks, Tom

NP205-TH350 transfer case. 200.00
Transfer case adapter w/coupler. 125.00
TH350 trans been rebuilt at some time. Nice fuild and clean pan. 250.00

Pic 1
Rear crossmember 40.00
intermediate cross member 45.00
front cross member 25.00
Transmission-transfer case cross member 65.00
cab frame mounts (2 fronts, 2 rears) 20.00 each
front spring/core support mounts 35.00 each LH one is ruff have a good one.
front spring rear shackle mounts 25.00 each
front bump stops w/brackets 10.00 each
front shock brackets 5.00 each
front LH spring stop 10.00
forward rear spring hangers 30.00 each
rear/rear spring hangers 25.00 each (only one in pic)
Front u-bolts with plates 30.00 per side
rear u-bolts w/plates 25.00 each Pic 3
rear bump stops w/brackets 12.50 each
box supports 6 of them 10.00 each
rear shock mounts 15.00 each
rear e-brake cable brackets 5.00 each
front exhaust hanger bracket 10.00
rear hyd brake line bracket 10.00
P/S steering conversion complete 125.00
steering intermediate shaft 25.00
steering rag joint 22.50 nice
fan shroud, minor fan rub on top. can not see when installed 85.00 very nice
original flex fan 10.00
AT pedal hanger and pedal 25.00
e-brake cables, support links, bracket, coulpers and spring. 45.00
transfer case support kit 45.00
trans-tcase rubber mount kit original 27.50
speedo cable minor blem in platisc 20.00 looks very nice
L71-72 RH axle (large u-joint) 75.00 nice
L71-72 LH axle (large u-joint) 75.00 nice
draglink tight ends 25.00
heat riser nice springs works perfect original 25.00
crank pulley 12.50
water pump pulley 2 groove 15.00

Pic 2
oil line 8.00
tail gate hardware on box 25.00
tail gate hardware in gate complete w/bolts 45.00
GMC letters good chrome needs black repainted 15.00
GMC park lamp wiring 10.00 each nice condition
heat stove pipe 12.50
washer hose set 12.50
tail lamp lens 10.00 nice condition
fender-core support triangles 5.00 each
door stricker plates 8.00 each

Pic 3
door panel seal 5.00
door latch rods 3.00 each
amber marker lenses 10.00 each nice color
red marker lens 10.00 nice color
GMC turn lens/housing 12.00 some fade
vent pull rods w/knobs 5.00 each
dome light switch wiring 10.00
fuel tank wiring 8.00
dome light wiring 10.00
inside door handle 5.00
window crank handles 6.50 each tight knobs
tail lamp housings 10.00 each
back up housings 7.50 each
LH outside door handle very nice driver quality 25.00
RH outside door handle chrome peeling 8.00
oil filter adapter 8.00
dip stick sleeve 5.00
heater controls needs center lever I will replace it 45.00
window weather strip channels 10.00 each

Misc pics
C/K20 71-72 power brake conversion 65.00
base black door panels very nice outside one has broken spot for one retainer the other has two melted spots from me heating the nuts to get armrest off. It would still work just fine. 60.00
steering colum black 60.00
4x4 AT tunnel cover 40.00

[tll74]

more pics

[68shortfleet]

Is the rear crossmember the same for 1/2 2wd and 3/4 4x4?

Would you do $40 shipped to 97115 on the crossmember?

[gmclonghorn]

I will take the flex fan . Pm thanks. zip code 92683

[gmc 2500 4x4]

is this the one with the hubs i asked about? if so, in line

[CUSTOM/10]

Interested in the high hump A/T tunnel !
Do you have the top radiator metel pipe ?
Drivers side door latch control ? The piece in the door the handle goes on .


Gary

[dec010974]

Hello. I'm looking for a set of rear bumper brackets.donyou have a set? Shipping is to Miami, Florida 33176.

[DeadheadNM]

Tom I'll take the front exhaust hanger bracket and speedo cable. Is the rear hanger there? Thanks, Pete

[mx289]

Interested in gmc fender eyebrow trim pieces,t-case support (just need rubbers+bolts ?),and speedo cable if pete passes.shipping would be to 07719.
Thanks,Tom

[20HDriver]

I'm interested in the top metal radiator pipe if you have one.

[blackbolt]

intrested in the trans crossmember, pm shipping to 77505 thanks JJ

[72swbcamo]

How much for the rear cab mount boltts?

[karphan]

I'll take the steering rag joint. Shipped to Sparks, NV 89441. PM sent. Thanks, Dan

[72longbed]

Do you still have the center tie rod that connected left knuckle and right knuckle? About 56" long with a tiee rod on each end.

Thanks,
72

[tll74]

Hang tight guys I'm at work till 5:00 and I'll catch up then. Thanks, Tom

[cst204x4]

I will take e-brake cables,supports, etc for 45.00 also e-brake rear brackets and rear hyd brake line bracket let me know a total shipped to 48817 thanks Mike also would you consider seperating the bump stops from the brackets?

[freakshow108]

What would be the cost of the fan shroud shipped to 98328? Thanks

[allons]

In pic#3, I'll take the 2 window weather strip channels @ $10 each. PM me so I can pay and get shipping to 43357. Thanks, Jim

[allons]

Also, would you have the 2 channels that the window glass in resting in? I need those also. Thanks, Jim

[sboris]

Second on the center ebrake cables. In line for top radiator pipe..

[jimer1964]

hi,intermediate cross member. large one in front of leaf spring hangers also power steering set up as well, but may be to much to ship! pa 19320 thanks

[CUSTOM/10]

What about the 4x4 AT tunnel cover, what kind of shape is it in ? Any rust, or extra holes ?

Gary

[freakshow108]

I will pass on the shroud, price was fine even with shipping, I found one local. Thank you for your time.

[teeitup]

Tom, do you have a throttle cable for a 4x4? Needing one for the blazer. Thanks Randy

[freakshow108]

My deal on a local fan shroud fell through. Ifvyounstill have the shroud I will take it. PM me your pay pal info and I will get it taken care of, thanks.I just noticed the last post, if I'm too late, just put me in line. Thanks.