Corvette C5 wheels, will they work?

[scottd03820]

I'm thinking of picking up a set of used C5 wheels for my 1975 C10. Will these work without modification to the truck (offset/bolt pattern)? Will it work on a lowered truck? Does anyone have any pictures of their truck with corvette wheels?

Thanks in advance.

[kwin]

different bolt pattern and offset.

[Aaron_L]

Not even close. You need thick adapters to make it work. They would probably cost more than the wheels.

[andrewmp6]

Most s10s i have seen them on used a inch and half spacer to make up for the back spacing.

[RandyP]

Originally Posted by andrewmp6

Most s10s i have seen them on used a inch and half spacer to make up for the back spacing.

But the horsepower gain is remarkable and well worth having the ricer look. Right?

[bnoon]

Ricer look for having Corvette wheels??? You sir misunderstand the term ricer!

scottd03820, you would need 5x5 to 5x4.75 adapters somewhere around 1.5 inches thick to run the Corvette wheels (depending on how wide the wheels are you're wanting to run). Should be $150-$200 for the set of 4, not too spendy at all.

[scottd03820]

Originally Posted by bnoon

Ricer look for having Corvette wheels??? You sir misunderstand the term ricer!

scottd03820, you would need 5x5 to 5x4.75 adapters somewhere around 1.5 inches thick to run the Corvette wheels (depending on how wide the wheels are you're wanting to run). Should be $150-$200 for the set of 4, not too spendy at all.

Bnoon, thanks for the response. Do you know who makes them? I'm assuming there's some reason guys aren't doing it because I don't see too many trucks with them?

[tylervalo]

The chrome C5 thin spokes were also bad for cracking, not sure I'd want them on a truck.

[mikentosh]

How about C6 wheels?



This picture doesn't do justice to how far off the backspacing is.

[scottd03820]

Originally Posted by mikentosh

How about C6 wheels?



This picture doesn't do justice to how far off the backspacing is.

Mikentosh, what did you have to use to get them to work? I think they look good but am curious to see what they look like once you get the fenders and bed on.

[mikentosh]

Originally Posted by scottd03820

Mikentosh, what did you have to use to get them to work? I think they look good but am curious to see what they look like once you get the fenders and bed on.

It's all custom. C6 spindles on the front and strange 9" rear with 5x4.75 bolt pattern.

I'm bringing a front fender to the shop tomorrow so I'll try to snap a photo.

[scottd03820]

Originally Posted by mikentosh

It's all custom. C6 spindles on the front and strange 9" rear with 5x4.75 bolt pattern.

I'm bringing a front fender to the shop tomorrow so I'll try to snap a photo.

Thanks for your response. I'm following your build. Very nice truck. I wish I could see a stock truck with spacers to see what it looks like. I like the thought of having corvette wheels but not sure its feasible without going the way you did.

[cory d]

camaro rotors and axles

[tylervalo]

Originally Posted by cory d

camaro rotors and axles

They are the same bolt pattern, but I think the rear axle is the same width as the Blazer and S10 axle though.

[mikentosh]

Here's a pic of how far off the backspacing is without a spacer:

[scottd03820]

Originally Posted by mikentosh

Here's a pic of how far off the backspacing is without a spacer:

Thanks Mikentosh. Wow they really are tucked in there. I'm assuming these are just mock up wheels and not the wheels you are using given the size of the tires I saw in another picture you posted? You stated those are C6 wheels? What size are they and did you have them painted or is that a stock color? I'm still thinking I'd like to go with the corvette wheels because you just don't see a lot of them on square body trucks. Thanks again.

[scottd03820]

Ok, another question. Will the S-10 wheel spacers work on my C-10? I'm only finding s-10 spacers on the internet.

[mikentosh]

Originally Posted by scottd03820

Thanks Mikentosh. Wow they really are tucked in there. I'm assuming these are just mock up wheels and not the wheels you are using given the size of the tires I saw in another picture you posted? You stated those are C6 wheels? What size are they and did you have them painted or is that a stock color? I'm still thinking I'd like to go with the corvette wheels because you just don't see a lot of them on square body trucks. Thanks again.

Yah these are just mockup wheels off another project in the shop. I believe they are 18" fronts and 19" backs. I can check next time I'm in there. Pretty sure they are C6 wheels in a gunmetal color. I'll probably do a similar color on the actual wheels.

I think it would look awesome with a set of these corvette wheels on a squarebody! You'll need to run some pretty wide spacers...there is almost 6" of space to the fender lip

[scottd03820]

Ok, another question. Will the S-10 wheel spacers work on my C-10? I'm only finding s-10 spacers on the internet.