63 to 66', rubber engine mount, 292 4x4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**aotte1** · 07-08-2014, 12:33 PM

Need a picture of the correct rubber engine mount for 63' to 66' 292 engine, 4x4 chassis, K10. Also if known, are they the same as for 250 and 283.
Thanks,
Les

**aotte1** · 07-08-2014, 12:49 PM

Pictures of ones have off 1983 250 that was in truck.

**aotte1** · 07-08-2014, 12:50 PM

Another pic from 250

**aotte1** · 07-08-2014, 12:51 PM

Another picture from 250

**aotte1** · 07-08-2014, 12:52 PM

Image of 250 another

**aotte1** · 07-08-2014, 12:53 PM

Last image of what I have

RANDY COX · 07-08-2014, 04:34 PM

Yep they are I took the ones off of my 307 v-8 and used them on my 292.

**aotte1** · 07-08-2014, 05:16 PM

Randy,
Thanks, will start putting 292 in tonight.

Les

RANDY COX · 07-10-2014, 06:33 AM

yes Don't know if you can see it in this pix.

If not I'll take you a better one this evening if no one else does b4 me...

pimpston65 · 07-10-2014, 06:38 AM

Quote:

Originally Posted by RANDY COX

yes Don't know if you can see it in this pix.

If not I'll take you a better one this evening if no one else does b4 me...

i seen that chain on it and was like it must been strong to not pull away, i was thinking it was part of the gear selection and not for the engagement of the clutch, so i got the system down now...glad this forum is full of gearheads like me that share info.

padresag · 07-13-2014, 07:35 PM

Here are what the 2 perches look like for a 292 in a 4 x 4

ron

RANDY COX · 07-13-2014, 08:35 PM

Quote:

Originally Posted by padresag

Here are what the 2 perches look like for a 292 in a 4 x 4

ron

Ron you are correct I should have mentioned that mine is a 1970 frame and they are different from earlier yrs.

padresag · 07-13-2014, 08:58 PM

this is the one from 67 and up 4 x 4 that I put in my 64 as I couldn't find a set from a 230,250 or 283, because mine were all removed when the 4 cyl Detroit went in an also the b/housing c/member was also changed. that eng cross member put some support back into the frame there as you don't have it with the side perches and that b/housing c/member gone.
with the 307 mounting you still had to change the r/s mount for the 292
ron

07-08-2014, 12:33 PM	#1
aotte1 Registered User Join Date: Oct 2013 Location: lousiville Ky Posts: 2,645	63 to 66', rubber engine mount, 292 4x4 Need a picture of the correct rubber engine mount for 63' to 66' 292 engine, 4x4 chassis, K10. Also if known, are they the same as for 250 and 283. Thanks, Les

07-08-2014, 12:49 PM	#2
aotte1 Registered User Join Date: Oct 2013 Location: lousiville Ky Posts: 2,645	Re: 63 to 66', rubber engine mount, 292 4x4 Pictures of ones have off 1983 250 that was in truck. Attached Images

07-08-2014, 12:50 PM	#3
aotte1 Registered User Join Date: Oct 2013 Location: lousiville Ky Posts: 2,645	Re: 63 to 66', rubber engine mount, 292 4x4 Another pic from 250 Attached Images

07-08-2014, 12:51 PM	#4
aotte1 Registered User Join Date: Oct 2013 Location: lousiville Ky Posts: 2,645	Re: 63 to 66', rubber engine mount, 292 4x4 Another picture from 250 Attached Images

07-08-2014, 12:52 PM	#5
aotte1 Registered User Join Date: Oct 2013 Location: lousiville Ky Posts: 2,645	Re: 63 to 66', rubber engine mount, 292 4x4 Image of 250 another Attached Images

07-08-2014, 12:53 PM	#6
aotte1 Registered User Join Date: Oct 2013 Location: lousiville Ky Posts: 2,645	Re: 63 to 66', rubber engine mount, 292 4x4 Last image of what I have Attached Images

07-08-2014, 04:34 PM	#7
RANDY COX Registered User Join Date: Mar 2001 Location: RADFORD, VA Posts: 2,651	Re: 63 to 66', rubber engine mount, 292 4x4 Yep they are I took the ones off of my 307 v-8 and used them on my 292. __________________ 1964 BBC 402 4x4

07-08-2014, 05:16 PM	#8
aotte1 Registered User Join Date: Oct 2013 Location: lousiville Ky Posts: 2,645	Re: 63 to 66', rubber engine mount, 292 4x4 Randy, Thanks, will start putting 292 in tonight. Les

07-10-2014, 06:33 AM	#9
RANDY COX Registered User Join Date: Mar 2001 Location: RADFORD, VA Posts: 2,651	Re: 63 to 66', rubber engine mount, 292 4x4 yes Don't know if you can see it in this pix. If not I'll take you a better one this evening if no one else does b4 me... __________________ 1964 BBC 402 4x4

07-13-2014, 07:35 PM	#11
padresag Registered User Join Date: Feb 2008 Location: Sidney,b.c. Posts: 4,425	Re: 63 to 66', rubber engine mount, 292 4x4 Here are what the 2 perches look like for a 292 in a 4 x 4 ron

07-13-2014, 08:58 PM	#13
padresag Registered User Join Date: Feb 2008 Location: Sidney,b.c. Posts: 4,425	Re: 63 to 66', rubber engine mount, 292 4x4 this is the one from 67 and up 4 x 4 that I put in my 64 as I couldn't find a set from a 230,250 or 283, because mine were all removed when the 4 cyl Detroit went in an also the b/housing c/member was also changed. that eng cross member put some support back into the frame there as you don't have it with the side perches and that b/housing c/member gone. with the 307 mounting you still had to change the r/s mount for the 292 ron



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.