|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
08-23-2014, 08:12 PM
|
#1 |
|
Registered User
Join Date: Apr 2014
Location: California
Posts: 975
|
Replacing 1967 C50 wheel studs?
Anybody know where to find them and how they are removed from the front and rear? Is it too hard to do myself?
|
|
|
|
08-25-2014, 11:44 PM
|
#2 |
|
Registered User
Join Date: Jun 2012
Location: happy valley or.
Posts: 106
|
Re: Replacing 1967 C50 wheel studs?
I had to do a front one on my c60. actually pretty easy. pound out or use a good air hammer. I was able to install the new one with the wheel on, through the hand hole, and tighten it into place by torquing the lug nut down
|
|
|
|
|
08-26-2014, 12:41 AM
|
#3 |
|
Registered User
Join Date: Apr 2014
Location: California
Posts: 975
|
Re: Replacing 1967 C50 wheel studs?
OK, now the fun part, where did you buy the thing? Thank you for the reply, sounds not to bad after all.
|
|
|
|
|
08-26-2014, 12:56 AM
|
#4 |
|
Registered User
Join Date: Jun 2012
Location: happy valley or.
Posts: 106
|
Re: Replacing 1967 C50 wheel studs?
I got mine at "6 robblees" I noticed there is one in oakland. but other trailer or truck repair parts houses. I think napa would have them
|
|
|
|
|
08-26-2014, 01:05 AM
|
#5 |
|
Registered User
Join Date: Jul 2011
Location: WV
Posts: 946
|
Re: Replacing 1967 C50 wheel studs?
Be careful on trying to pull the stud in with the lug nut. You may overtorque the nut. It is best to press them in.
__________________
72 GMC C2500 402/Th400 first truck (still have) 77 GMC C3500 CC dually Sold  70 C50 dump truck "Rusty" 87 K10 Suburban Sold 93 K2500 xcab 6.5TD 96 GMC K2500 Suburban 6.5 TD |
|
|
|
|
08-26-2014, 01:19 AM
|
#6 |
|
At the body shop.
Join Date: Aug 2009
Location: Land of fruits and nuts.
Posts: 5,254
|
Re: Replacing 1967 C50 wheel studs?
Betts spring should be able to get one
__________________
" That didnt make it any newer " " Dont antique the equipment " |
|
|
|
|
08-26-2014, 01:26 AM
|
#7 |
|
Registered User
Join Date: Jun 2012
Location: happy valley or.
Posts: 106
|
Re: Replacing 1967 C50 wheel studs?
I have always pulled them in with the nut just dont use a impact or cheater bar. frequently check that the head is seated then torque to proper specs.
|
|
|
|
|
08-26-2014, 01:27 AM
|
#8 |
|
Registered User
Join Date: Jun 2012
Location: happy valley or.
Posts: 106
|
Re: Replacing 1967 C50 wheel studs?
I did strip one. that was when I was using a torque multiplier, it took about 400 foot lbs to strip it with a 60x torque multplier.
|
|
|
|
|
08-26-2014, 09:33 PM
|
#9 |
|
Registered User
Join Date: Apr 2014
Location: California
Posts: 975
|
Re: Replacing 1967 C50 wheel studs?
What is the torque spec for lug nuts on these big trucks?
Thank you to everyone for the help. |
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
