NY Cutting up old Cab / Extra parts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

DD1 · 08-24-2014, 09:55 PM

I am working on repairing a cab I bought from another board member that needs less work than my original cab. I will need to get rid of my first cab soon, so if anyone needs any pieces, let me know. I will post pics as soon as I get to my PC (working on an Ipad). I have to make space in my garage and help pay for some of the complete floor pan I just ordered.

I will list parts in this post, and add photos of the cab and other leftover parts below. All parts are plus shipping.

1. Dashboard - REDUCED TO $60 - Anybody interested?: This is my first time removing a dashboard, and I think I did an okay job. The radio part was cut out by previous owner. Dash has small hole in lower right corner. Might need a little fixing where the dash meets the cowl. I was not sure what to ask for this, so please let me know if the price is not where it should be.

2. Tabco driver's side rear Cab Support (new) - $10 (Tabco price is $14.50).

3. Triplus LH Floor panel new - $15 (similar panels sell for $26 new). SOLD

4. Inner Rocker Panel patch (I think it's Triplus also) - $5 SOLD

5. Triplus Cab support RH (I believe it's the rear support) - $10.

6. Cab Support - Slip On Covers, Triplus brand, don't know if anyone will actually want these. - $7 each.

7. The back half of the floor pan is pretty solid. I believe the cab supports are shot, but the floor is still pretty nice. If anyone is interested I will figure out a price.

8. Anyone interested in an outer roof?

chubinit · 08-24-2014, 10:05 PM

How much for the Triplus LH Floor panel and the Inner Rocker Panel patch shipped to 27892?
Thanks,
chubinit

DD1 · 08-24-2014, 10:39 PM

Quote:

Originally Posted by chubinit

How much for the Triplus LH Floor panel and the Inner Rocker Panel patch shipped to 27892?
Thanks,
chubinit

Check out the pics, make sure you are good with them, and I'll find a box and get a quote tomorrow.

Pics: Tabco Rear Support & Inner Rocker Panel, Triplus floor pan front and back shot,

DD1 · 08-28-2014, 05:47 PM

Quote:

Originally Posted by chubinit

How much for the Triplus LH Floor panel and the Inner Rocker Panel patch shipped to 27892?
Thanks,
chubinit

Hey Chubinit,

I am sorry to take so long, but it's been really difficult trying to box this thing up. The floor panel is a rough shape to work with. I am going to try and create a custom box and get a quote.

Let me know if you are still interested.

Thanks!

**zicc1835** · 08-24-2014, 10:16 PM

low or high hump?... need low hump patch PO cut big hole for floor shifter

DD1 · 08-24-2014, 10:44 PM

Quote:

Originally Posted by zicc1835

low or high hump?... need low hump patch PO cut big hole for floor shifter

It's a low hump. I think the PO cut a shifter hole in mine also, but I don't think it's that big of a hole. I cut a piece out of the right side floor, but I don't think that will affect the hump.

You are still online as I am typing this (10:44 EST); I'll get a couple of quick pics and edit this post.

Okay, here are the pics. I have not cleaned the cab out so, excuse the mess. The hump looks to me like it's in pretty decent shape. There is a small hole for the transmission. It is dirty, there is rust dust on it from removing the dashboard. I can clean it up tomorrow and send another pic if you want.

If you are interested, we can figure out a price, and I will need to know exactly where to cut, and then I will probably still add a couple inches. Thanks!

**zicc1835** · 08-24-2014, 10:55 PM

Quote:

Originally Posted by DD1

It's a low hump. I think the PO cut a shifter hole in mine also, but I don't think it's that big of a hole. I cut a piece out of the right side floor, but I don't think that will affect the hump.

You are still online as I am typing this (10:44 EST); I'll get a couple of quick pics and edit this post. Give me about 15 minutes.

thanks

**zicc1835** · 08-24-2014, 11:11 PM

thats going to work for me, ill take some pics and measurements send to you and LMK what you need for it
THANKS.....
jz

Quote:

Originally Posted by DD1

It's a low hump. I think the PO cut a shifter hole in mine also, but I don't think it's that big of a hole. I cut a piece out of the right side floor, but I don't think that will affect the hump.

You are still online as I am typing this (10:44 EST); I'll get a couple of quick pics and edit this post.

Okay, here are the pics. I have not cleaned the cab out so, excuse the mess. The hump looks to me like it's in pretty decent shape. There is a small hole for the transmission. It is dirty, there is rust dust on it from removing the dashboard. I can clean it up tomorrow and send another pic if you want.

If you are interested, we can figure out a price, and I will need to know exactly where to cut, and then I will probably still add a couple inches. Thanks!

DD1 · 08-24-2014, 11:00 PM

Dashboard pics:

DD1 · 08-24-2014, 11:07 PM

Other parts of the cab are up for grabs as well, as long as I don't need it on my replacement cab. This cab is a Non-A/C, the new cab is an A/C cab, so I won't be needing some of the heating parts.

Here are some rough pics. I clean the cab and get some better shots tomorrow.

**zicc1835** · 08-24-2014, 11:40 PM

looks like 8 by 10 will give me enough LMK if you need any other pics

DD1 · 08-24-2014, 11:47 PM

Quote:

Originally Posted by zicc1835

looks like 8 by 10 will give me enough LMK if you need any other pics

Wow. That is a big hole. Would you please send me a pic of your hump that is a bit further back. I just need to see more of the floor to make sure I cut the right area.

DD1 · 08-25-2014, 12:01 AM

Quote:

Originally Posted by zicc1835

looks like 8 by 10 will give me enough LMK if you need any other pics

I sent you a PM.

**zicc1835** · 08-25-2014, 12:28 AM

hope these help

DD1 · 08-25-2014, 12:41 AM

Quote:

Originally Posted by zicc1835

hope these help

That works. I read your last PM. I'll mark it up, post some pics, cut it up and post some more pics. We can touch base after Labor Day.

**zicc1835** · 08-25-2014, 12:43 AM

thanks enjoy the holiday......

Quote:

Originally Posted by DD1

That works. I read your last PM. I'll mark it up, post some pics, cut it up and post some more pics. We can touch base after Labor Day.

68Bowtie4x4 · 08-25-2014, 12:49 AM

How much for the center section of the cab back wall from the bottom rear window molding seam to the floor and about 2 or 2.5" wide?

DD1 · 08-30-2014, 11:58 AM

Quote:

Originally Posted by 68Bowtie4x4

How much for the center section of the cab back wall from the bottom rear window molding seam to the floor and about 2 or 2.5" wide?

68bowtie, Here is a pic of what I plan to cut for you. I measured 59-1/2" for the window, and 29-3/4" as the center. My center mark is actually at 29-1/2", but I went 13" out to compensate, and will probably cut a bit outside that as well. Let me know if this works for you.

You can see my markings just above the blue tape. The end pieces say 13" and the center marking is in the middle.

DD1 · 08-30-2014, 11:52 AM

Quote:

Originally Posted by zicc1835

looks like 8 by 10 will give me enough LMK if you need any other pics

Quote:

Originally Posted by zicc1835

hope these help

Hey Jess, I taped off the section I plan to cut for you. Let me know if this works. My intent is too cut on the inside edge of the tape.

**zicc1835** · 08-30-2014, 05:22 PM

Yes that will give me plenty of room thank you
Jess

Quote:

Originally Posted by DD1

Hey Jess, I taped off the section I plan to cut for you. Let me know if this works. My intent is too cut on the inside edge of the tape.

68Bowtie4x4 · 08-31-2014, 01:35 AM

That looks great DD1. I finally got the camper down to my house now after getting fuel in it and getting it fired up. It will be much easier to work on it now.

Thanks,

Doug

DD1 · 08-31-2014, 04:29 PM

Quote:

Originally Posted by 68Bowtie4x4

That looks great DD1. I finally got the camper down to my house now after getting fuel in it and getting it fired up. It will be much easier to work on it now.

Thanks,

Doug

Great! I need a little time on yours... I have to remove the cab from the frame so I can drill out the spot welds in the back for you. As you might be able to tell from the pics, space is not something I have a lot of. I'll try and figure something out on Monday.

DD1 · 09-01-2014, 03:13 PM

Quote:

Originally Posted by 68Bowtie4x4

That looks great DD1. I finally got the camper down to my house now after getting fuel in it and getting it fired up. It will be much easier to work on it now.

Thanks,

Doug

Doug, I am very close to cutting your part out. I have removed the roof of the cab. Next I will cut the bottom part in half and remove the front. Then I can move the back half and get access to the spot welds.

DD1 · 09-12-2014, 08:25 PM

Quote:

Originally Posted by 68Bowtie4x4

That looks great DD1. I finally got the camper down to my house now after getting fuel in it and getting it fired up. It will be much easier to work on it now.

Thanks,

Doug

Hey Doug, i got your piece all boxed up and ready to ship. What's your zip code? I'll pic a random OR zip to get an estimate and PM you. I can figure out the actual cost when I get your actual zip.

orngsikL · 08-25-2014, 03:38 AM

what about the driver side roof section at the windshield?

08-24-2014, 09:55 PM	#1
DD1 Registered User Join Date: Aug 2011 Location: new york, ny Posts: 1,063	Cutting up old Cab / Extra parts I am working on repairing a cab I bought from another board member that needs less work than my original cab. I will need to get rid of my first cab soon, so if anyone needs any pieces, let me know. I will post pics as soon as I get to my PC (working on an Ipad). I have to make space in my garage and help pay for some of the complete floor pan I just ordered. I will list parts in this post, and add photos of the cab and other leftover parts below. All parts are plus shipping. 1. Dashboard - REDUCED TO $60 - Anybody interested?: This is my first time removing a dashboard, and I think I did an okay job. The radio part was cut out by previous owner. Dash has small hole in lower right corner. Might need a little fixing where the dash meets the cowl. I was not sure what to ask for this, so please let me know if the price is not where it should be. 2. Tabco driver's side rear Cab Support (new) - $10 (Tabco price is $14.50). 3. Triplus LH Floor panel new - $15 (similar panels sell for $26 new). SOLD 4. Inner Rocker Panel patch (I think it's Triplus also) - $5 SOLD 5. Triplus Cab support RH (I believe it's the rear support) - $10. 6. Cab Support - Slip On Covers, Triplus brand, don't know if anyone will actually want these. - $7 each. 7. The back half of the floor pan is pretty solid. I believe the cab supports are shot, but the floor is still pretty nice. If anyone is interested I will figure out a price. 8. Anyone interested in an outer roof? __________________ ___________________________________________ Darien 1971 C10 LWB http://67-72chevytrucks.com/vboard/s...d.php?t=502964 Last edited by DD1; 09-12-2014 at 09:53 PM. Reason: Added item

08-24-2014, 10:05 PM	#2
chubinit Registered User Join Date: May 2012 Location: Williamston, NC Posts: 37	Re: Cutting up old Cab / Extra parts How much for the Triplus LH Floor panel and the Inner Rocker Panel patch shipped to 27892? Thanks, chubinit

08-24-2014, 10:16 PM	#5
zicc1835 Senior Member Join Date: Mar 2011 Location: Hanover NJ Posts: 4,163	Re: Cutting up old Cab / Extra parts low or high hump?... need low hump patch PO cut big hole for floor shifter __________________ Doc & Kim build http://67-72chevytrucks.com/vboard/s...d.php?t=722288 I am from the desert http://67-72chevytrucks.com/vboard/s...d.php?t=650332 basket case build SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=648557

08-24-2014, 11:00 PM	#9
DD1 Registered User Join Date: Aug 2011 Location: new york, ny Posts: 1,063	Re: Cutting up old Cab / Extra parts Dashboard pics: Attached Images __________________ ___________________________________________ Darien 1971 C10 LWB http://67-72chevytrucks.com/vboard/s...d.php?t=502964

08-24-2014, 11:07 PM	#10
DD1 Registered User Join Date: Aug 2011 Location: new york, ny Posts: 1,063	Re: Cutting up old Cab / Extra parts Other parts of the cab are up for grabs as well, as long as I don't need it on my replacement cab. This cab is a Non-A/C, the new cab is an A/C cab, so I won't be needing some of the heating parts. Here are some rough pics. I clean the cab and get some better shots tomorrow. Attached Images __________________ ___________________________________________ Darien 1971 C10 LWB http://67-72chevytrucks.com/vboard/s...d.php?t=502964

08-24-2014, 11:40 PM	#11
zicc1835 Senior Member Join Date: Mar 2011 Location: Hanover NJ Posts: 4,163	Re: Cutting up old Cab / Extra parts looks like 8 by 10 will give me enough LMK if you need any other pics Attached Images __________________ Doc & Kim build http://67-72chevytrucks.com/vboard/s...d.php?t=722288 I am from the desert http://67-72chevytrucks.com/vboard/s...d.php?t=650332 basket case build SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=648557

08-25-2014, 12:28 AM	#14
zicc1835 Senior Member Join Date: Mar 2011 Location: Hanover NJ Posts: 4,163	Re: Cutting up old Cab / Extra parts hope these help Attached Images __________________ Doc & Kim build http://67-72chevytrucks.com/vboard/s...d.php?t=722288 I am from the desert http://67-72chevytrucks.com/vboard/s...d.php?t=650332 basket case build SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=648557

08-25-2014, 12:49 AM	#17
68Bowtie4x4 Registered User Join Date: Oct 2003 Location: Athena, Oregon Posts: 167	Re: Cutting up old Cab / Extra parts How much for the center section of the cab back wall from the bottom rear window molding seam to the floor and about 2 or 2.5" wide? __________________ 72 Chevy Cheyenne K10 4x4 LWB, 4" lift kit, 350/350/NP205, rebuild in progress.

08-31-2014, 01:35 AM	#21
68Bowtie4x4 Registered User Join Date: Oct 2003 Location: Athena, Oregon Posts: 167	Re: Cutting up old Cab / Extra parts That looks great DD1. I finally got the camper down to my house now after getting fuel in it and getting it fired up. It will be much easier to work on it now. Thanks, Doug __________________ 72 Chevy Cheyenne K10 4x4 LWB, 4" lift kit, 350/350/NP205, rebuild in progress.

08-25-2014, 03:38 AM	#25
orngsikL Registered User Join Date: Oct 2011 Location: Watson, Louisiana Posts: 312	Re: Cutting up old Cab / Extra parts what about the driver side roof section at the windshield? __________________ build thread - 1972 C/10 "Ethyl" 1974 C/10 " Paw Paw" C/10 Club Louisiana instagram - @esso_c10 @projectpawpaw



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.