Lets see some Artillery!!!

[Rambow]

I have a pair of 15x5 or 15x6" (unsure) Artillary wheels on the back of my '53

It needs new tires, and I figure it would be cool to move these up to the front, and get a pair of 15x8 for the rear so all four match.

I've done a bunch of searching, and don't see too many of these on AD trucks...
I attached a couple pics i found on HotRods website... I'm thinking similar sizing & stance for my truck, but black wall tires.

Anybody out there running Artillery wheels & want to share some pics?

Thanks!
Ben

[wood1]

17" & 18" on my '51 I sold last year

[flashed]

Nice truck ,are you the same Rambow on Team Chevelle ?

[Rambow]

Originally Posted by flashed

Nice truck ,are you the same Rambow on Team Chevelle ?

The one and only!
I've noticed a lot of TC folks over here!

[Old Crow]

Here's my wife's levitating panel truck.






Question, I notice these rims have the centers riveted to the outsides. Are they sealed in a way that allows them to be run tubeless?
If not, that might explain why none of the tires held air for more than a day or two.

[Rambow]

Pic of the ones from my truck... I've repainted these, and the other stock ones semi-gloss black so they'd all match.

Thinking about going gunmetal grey on the wheels when i get the new ones... Might also see if i can get some cans of the green made up to match the little bit of green left on the truck.

They'll get new stainless caps & narrow ribbed rings.

[wood1]

Originally Posted by Rambow

Pic of the ones from my truck... I've repainted these, and the other stock ones semi-gloss black so they'd all match.

Thinking about going gunmetal grey on the wheels when i get the new ones... Might also see if i can get some cans of the green made up to match the little bit of green left on the truck.

They'll get new stainless caps & narrow ribbed rings.

Check thewheelsmith.net talk to Chris or Rex, they'll help you out

[NEWFISHER]

Mine:

[NEWFISHER]

Anyone step up to wheel vintiques 17 inch artilleries yet? I saw them at the Santa Maria West Coast Customs show last year on a rolling chassis but have seen them on a finished truck yet.

[NEWFISHER]

After a few months a set finally showed up...waiting for paint to dry and then off to the pinstriper

[lowrodderchev]

Originally Posted by NEWFISHER

After a few months a set finally showed up...waiting for paint to dry and then off to the pinstriper

Those are sweet

[NEWFISHER]

First pass with first color on the 17x7s. 2 thin red/grey stripes along the lip comming. Spyders and thin rings ( if I can find thin rings in 17)

[Advanced Design]

Those look good Newfisher. Which of your vehicles are these going on?

[NEWFISHER]

The 46 burb. My phone took a swim and dont have any good ones on this new one yet, too much camping

[lowrodderchev]

I want a set of these for my fleetline

[NEWFISHER]

Playing with an outer stripe

[NEWFISHER]

Tying in these colors

[NEWFISHER]

3 tries at tires that would fit with offset , bagged rear etc. But they are on and rolling.

[solidaxel]

.......... TEN - FOUR, on the offset!
We are having the same problem with wheels, what did you end up with?


In the 4th picture there is a filler piece between upper and lower part of the grille, does anyone know where I can find one

[NEWFISHER]

Originally Posted by solidaxel

.......... TEN - FOUR, on the offset!
We are having the same problem with wheels, what did you end up with?


In the 4th picture there is a filler piece between upper and lower part of the grille, does anyone know where I can find one

17X7 4.5 BS and a 215/65/17 tire is THE MAX it will accept. Im playing with longer rear studs, spacers and adapters tomorrow night to "center" the wheel in the tub/fender to get full drop in the rear. With the stock wheels and a 225/75/15 it would lay 1/2 off the pavement. Its now 1 1/4, not a big deal, but I think I can move the wheel out a smidge and get it to drop over the tire.

Jim Carter on the filler?

[Dan in Pasadena]

Curious: Anyone ever put artilleries on a Task Force truck?