|
|
|
02-08-2015, 08:50 PM
|
#1 |
|
user # 2756
 
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
door latch
Anybody have dimensions of the rod that goes to the inside handle to the lock mechanism? Mine was a little bent but not sure which bends are correct. Thanks,
Jim
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
02-10-2015, 09:08 AM
|
#2 |
|
user # 2756
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Re: door latch
I think the factory bend is a "V shape" in the middle, anybody?
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm
|
|
|
|
|
02-10-2015, 10:50 AM
|
#3 |
|
Registered User
Join Date: Dec 2013
Location: Durango, CO
Posts: 827
|
Re: door latch
Mine are extra bent on purpose - I had to in order to make the latches work. If you can get an eye on the latch (roll the window down and look through the top of the door), it's pretty easy to see what's happening when you operate the handle, and then easy to figure out whether the rod needs to be shorter or longer. Bend accordingly. Can't remember if there's a threaded fitting on one end for small adjustment, seem to remember that... but in my truck (if that fitting exists) it wasn't enough to make the door handles work.
__________________
1972 K10 Cheyenne Super | LWB, fleetside | 350/350/205 | KEEPER 1971 K10 Cheyenne | SWB, fleetside | LS Swap 5.3/4L60 | SOLD 1976 Trans Am | 400/4-spd | SOLD 1976 Trans Am | 455/4-spd | TOTALED
|
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
